Actions

Difference between revisions of "2-2e. Event Trigger - Event Handler (practice)"

From Zenitel Wiki

(Exercise)
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{stub}}
+
[[File:2-2d exercise.PNG|left|thumb|500px|System configuration]]
 
 
[[File:2-2e exercise.PNG|left|thumb|500px|System configuration]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
 
=== Exercise ===
 
=== Exercise ===
  
'''Scheduling''':
+
'''Exercise goal:''' Learn how to use the Event Trigger as a toggle feature and execute multiple actions in the AlphaCom. Learn about UDD's, and IF and STOP statements.
* At 15:00 a prerecorded message "We ask passengers not to leave their luggage unattended..." should be distributed to the stations in group 87.
+
 
 +
'''Call setup:'''
 +
* The Entrance and the SOS Point should be configured to make a Call Request (623 + 101) to the Control Room.
 +
* The Control Room should be configured as a CRM (Control Room Master), the DAK display should be enabled, and the Navigation Keys should be used for call queue navigations.
 +
 
 +
 
 +
 
 +
'''Toggle Call Request Forwarding:'''
 +
* When dialing the event trigger number 9533, or when pressing a DAK key programmed to 9533 on the Control Room station, the following features should be toggled ON/OFF every time the number is activated:
 +
** Turn on/off Call Request Forwarding from Control Room station 101 to station 103 (M. Larsen), so that all new call requests will be forwarded to station 103. Use the command "$SCRT" for this.
 +
** Turn on/off a lamp (use RCO 3) to signal that call forwarding is active
 +
** Write to the System LOG that the call forwarding has been activated/turned off. Use the LOG "..." statement.
 +
 
 +
(Hint: Use a UDD to store the current state, 1 = ON, 0 = OFF. Use the IF statement to check the current status of the UDD when 9533 is dialed, and set or reset the call forwarding, RCO and LOG data accordingly).
  
  
Tip:
 
* Use AlphaWeb to upload a wav-file as alarm message 3, dir no 8193 (wav file is found on the memory stick)
 
* Use the $GM command to dispatch the message
 
  
  

Latest revision as of 17:38, 6 November 2013

System configuration


Exercise

Exercise goal: Learn how to use the Event Trigger as a toggle feature and execute multiple actions in the AlphaCom. Learn about UDD's, and IF and STOP statements.

Call setup:

  • The Entrance and the SOS Point should be configured to make a Call Request (623 + 101) to the Control Room.
  • The Control Room should be configured as a CRM (Control Room Master), the DAK display should be enabled, and the Navigation Keys should be used for call queue navigations.


Toggle Call Request Forwarding:

  • When dialing the event trigger number 9533, or when pressing a DAK key programmed to 9533 on the Control Room station, the following features should be toggled ON/OFF every time the number is activated:
    • Turn on/off Call Request Forwarding from Control Room station 101 to station 103 (M. Larsen), so that all new call requests will be forwarded to station 103. Use the command "$SCRT" for this.
    • Turn on/off a lamp (use RCO 3) to signal that call forwarding is active
    • Write to the System LOG that the call forwarding has been activated/turned off. Use the LOG "..." statement.

(Hint: Use a UDD to store the current state, 1 = ON, 0 = OFF. Use the IF statement to check the current status of the UDD when 9533 is dialed, and set or reset the call forwarding, RCO and LOG data accordingly).








Related articles