Actions

Difference between revisions of "Turbine Compact Board Connectors"

From Zenitel Wiki

 
(24 intermediate revisions by 3 users not shown)
Line 1: Line 1:
=Main PCB=
+
{{AEIPS}}
==Front==
+
==Main PCB (A100C08121) ==
 +
===Front===
 
[[File:TCIS Connections 3.PNG|500px]]
 
[[File:TCIS Connections 3.PNG|500px]]
  
Line 10: Line 11:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
 
+
'''P2''' 5-pin plug-on terminal for relay and external power
 
 
'''P2''' 6-pin plug-on terminal for external connections.
 
 
[[File:TCIS Connections 5.PNG|thumb|500px|left]]
 
[[File:TCIS Connections 5.PNG|thumb|500px|left]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
:Pin 1/2  24 VDC for external secondary power if PoE is not used. Pin 1 is positive.
+
:Pin 1/2: 24 VDC for external secondary power if PoE is not used. Pin 1 is positive.
:Pin 3 COM relay
+
:Pin 3: COM relay (Common)
:Pin 4 NO relay
+
:Pin 4: NO relay (Normally Open)
:Pin 5 NC relay
+
:Pin 5: NC relay (Normally Closed)
 
 
The relay can switch and carry continuously 60W power maximum.
 
So with maximum current 2A, it can take maximum 30V, or with maximum voltage 250VAC it can take maximum 240mA.
 
 
 
'''P4'''  Loudspeaker & Electret microphone
 
[[File:TCIS Connections 7.PNG|thumb|500px|left]]
 
<br style="clear:both;" />
 
:Pin 1  10W Speaker amplifier +
 
:Pin 2  10W Speaker amplifier -
 
:Pin 3  Electret Microphone +
 
:Pin 4  Electret Microphone -
 
  
'''Note''': To enable the electret microphone input when using a [[TKIS-2]], the "Frontboard" must be set to "Kit" under '''Station Main Settings''' in the web interface of the device.
+
* Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
 +
* Connectable conductors:  0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
  
'''P3'''  10-pin plug-on terminal for external connections.
+
'''P3'''  10-pin plug-on terminal for I/O's and Audio Line Out
 
[[File:TCIS Connections 6.PNG|thumb|300px|left]]
 
[[File:TCIS Connections 6.PNG|thumb|300px|left]]
  
Line 48: Line 37:
  
 
<br style="clear:both;" />
 
<br style="clear:both;" />
 +
* Connectable conductors:  0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
 +
 +
'''P4'''  Loudspeaker & Electret microphone
 +
[[File:TCIS Connections 7.PNG|thumb|500px|left]]
 +
<br style="clear:both;" />
 +
:Pin 1: Speaker output +
 +
:Pin 2: Speaker output -
 +
:Pin 3:  Electret Microphone +
 +
:Pin 4:  Electret Microphone -
 +
 +
* Connectable conductors:  0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
 +
* Recommended loudspeaker impedance: 8 ohms
 +
 +
{{Note | To enable the electret microphone input when using a [[TKIS-2]], the "'''Product Model And Accessory'''" must be set to "'''Kit'''" under [[Main Settings (IP Stations)|Station Main > Main Settings]] in the web interface of the device.}}
 +
 +
  
==Output Connectors + 1 relay==
+
===Output Connectors + 1 relay===
 
[[File:TCIS Connections 12.PNG|500px|Connecting to the onboard relay. Extra LED controlled by output 1]]
 
[[File:TCIS Connections 12.PNG|500px|Connecting to the onboard relay. Extra LED controlled by output 1]]
  
Line 60: Line 65:
 
The 5,3V output can deliver 200mA current maximum
 
The 5,3V output can deliver 200mA current maximum
  
See also [[Turbine Compact and MRBD]]
+
See also [[Adding additional relay(s) to a Zenitel IP Device]]
  
==Rear==
+
===Rear===
 
[[File:TCIS Connections 8.PNG|500px]]
 
[[File:TCIS Connections 8.PNG|500px]]
  
Line 81: Line 86:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
=Front Board=
+
==Front Board (A100C08129)==
  Note! Not applicable to TKIS-2 and TMIS-x
+
  {{Note | Not applicable to TKIS-2 and TMIS-x}}
==Front==
+
===Front===
 
[[File:TCIS Connections 10.PNG|500px]]
 
[[File:TCIS Connections 10.PNG|500px]]
  
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
==Rear==
+
===Rear===
 
[[File:TCIS Connections 11.PNG|500px]]
 
[[File:TCIS Connections 11.PNG|500px]]
  
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
[[Category: Turbine]]
+
[[Category: Turbine Connections]]

Latest revision as of 15:22, 23 June 2023

AEIPS.png

Main PCB (A100C08121)

Front

TCIS Connections 3.PNG


P1 RJ45 PoE port for 10/100 Mbit Ethernet connection.

The station can be powered from this port if the line supports Power over Ethernet (PoE).
TCIS Connections 4.PNG


P2 5-pin plug-on terminal for relay and external power

TCIS Connections 5.PNG


Pin 1/2: 24 VDC for external secondary power if PoE is not used. Pin 1 is positive.
Pin 3: COM relay (Common)
Pin 4: NO relay (Normally Open)
Pin 5: NC relay (Normally Closed)
  • Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
  • Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².

P3 10-pin plug-on terminal for I/O's and Audio Line Out

TCIS Connections 6.PNG
Pin 1 5.3V (max. 200mA current)
Pin 2 GND
Pin 3 Button Input or LED Driver
Pin 4 Button Input or LED Driver
Pin 5 Button Input or LED Driver
Pin 6 Button Input or LED Driver
Pin 7 Button Input or LED Driver
Pin 8 Button Input or LED Driver
Pin 9 600 ohm balanced line out +
Pin 10 600 ohm balanced line out -


  • Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².

P4 Loudspeaker & Electret microphone

TCIS Connections 7.PNG


Pin 1: Speaker output +
Pin 2: Speaker output -
Pin 3: Electret Microphone +
Pin 4: Electret Microphone -
  • Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
  • Recommended loudspeaker impedance: 8 ohms
Note icon To enable the electret microphone input when using a TKIS-2, the "Product Model And Accessory" must be set to "Kit" under Station Main > Main Settings in the web interface of the device.



Output Connectors + 1 relay

Connecting to the onboard relay. Extra LED controlled by output 1

The extra relay for any of the 6 I/O pins is connected as shown:

TurbineCompactOutputs.PNG

Most general purpose P-Channel MOSFET's should work. Recommended example: BSS84

The 5,3V output can deliver 200mA current maximum

See also Adding additional relay(s) to a Zenitel IP Device

Rear

TCIS Connections 8.PNG


J6 10-pin terminal for digital MEMS Microphone

TCIS Connections 9.PNG
Pin 1 Left mic select (Vdd)
Pin 2 Right mic select (GND)
Pin 3 Data
Pin 4 Data
Pin 5 Vdd 3.3V
Pin 6 Vdd 3.3V
Pin 7 CLK
Pin 8 CLK
Pin 9 GND
Pin 10 GND


Front Board (A100C08129)

Note icon Not applicable to TKIS-2 and TMIS-x


Front

TCIS Connections 10.PNG


Rear

TCIS Connections 11.PNG