Difference between revisions of "ABSD Billing"
From Zenitel Wiki
(→AlphaCom User interface for dialling) |
(→Startup Sequence) |
||
Line 19: | Line 19: | ||
At startup ABSD sends "#!ABSD 0/198 VER:xxxx" + a [[RESET_TAKEN]] message. | At startup ABSD sends "#!ABSD 0/198 VER:xxxx" + a [[RESET_TAKEN]] message. | ||
− | AMCD responds to RESET_TAKEN message with [[COMMAND_RESPONSE]]. Response code is 1 = License OK, or 4 = not license. | + | AMCD responds to RESET_TAKEN message with [[COMMAND_RESPONSE]]. Response code (2) is 1 = License OK, or 4 = not license. Number of license in parameter 3 |
== Call charging overview == | == Call charging overview == |
Revision as of 09:07, 10 June 2008
New Data protocol messages
CDC_STATE from AMCD to ABSD <br\> CDC_CMD from ABSD to AMCD <br\>
Contents
Basic Concept
CDC = Call Detail Control ABSD = AlphaCom Billing Service Daemon
A AlphaCom can host a ABSD process for billing services. ABSD requires an external CIFS mounted network disk for the data storage, but the application it self runs from local flash filesystem. ABSD handle the realtime authorization and charging of outgoing calls. Configuration and invoicing is handled by a BillingWeb application.
The ABSD software communicates with the local AMCD using Stentofon Simple Link Layer. The ABSD software is defined as device number 198, and connects to local AMCD on TCP port 127.0.0.1/40002. In AlphaNet, remote AlphaComs communicates with ABSD via the hosting AMCD using the normal AlphaNet routing.
Startup Sequence
At startup ABSD sends "#!ABSD 0/198 VER:xxxx" + a RESET_TAKEN message.
AMCD responds to RESET_TAKEN message with COMMAND_RESPONSE. Response code (2) is 1 = License OK, or 4 = not license. Number of license in parameter 3
Call charging overview
AlphaCom behavior is based on adding CDC handling to directory numbers using feature 81, Call to remote EXCHANGE and 83, Direct Global Number. When dialling feature 81/83 to dest_node, AMCD checks .module_profile.node_profile[dest_node].absd_node. If absd_node is different from null, CDC handling is activated for the call. dest_node is usually a SIP-server. absd_node is the node number hosting the ABSD.
When CDC handlig is active, AMCD buffers all dialled by the user, as well forwards the digits to ABSD as CDC_STATE(,,DIGIT,). ABSD decides whether digits are PIN code, trunk number, or digits to be sent to SIP.
When ABSD has recognized a PIN code or a trunk number, it sends CDC_CMD back to AMCD. The CDC_CMD contains code for the current state of dialing, and the number of digits which was associated with this part of the dialing sequence. AMCD removes the given number of digits from the start of the buffer. When ABSD sends CDC_CMD(,,TRUNK_SET...), AMCD opens the SIP connection, and send the remaining buffered digits to the SIP connection.
AlphaCom User interface for dialling
- When dial PIN
- Short pip (handset off dialling)
- Display * ?
- When SIP connection starts:
- Reset display line 2, dont show PIN/trunk code
- Dialtone from SIP
- When aborted due to failed PIN/barred number/overdrawn account:
- Failure tone
AlphaPro Config
New NVRAM field: module_profile.node_profile[dest_node].absd_node.
This will appear in AlphaPro, "net routing"/"Advanced settings". absd_node must be set in all AlphaComs which are to use the billing service.
Digit Collection
Example 1:<br\> System setup: <br\> AudioCodes SIP gateway, trunk line 1 programmed with number 0047. <br\> 0047 programmed in AlphaCom as feature 83 global number with flag for Call Detail Control.<br\>
ABSD programmed with pin code "12" for user "101" <br\>
User "101" dials trunk extension "0047" then local number 64871300
AMCD ABSD CDC_STATE (REF, 101, START, 0047) -----> (Starts new billing process) CDC_STATE (REF, 101, DIGIT, 1) -----> (Verify pin digits) CDC_STATE (REF, 101, DIGIT, 2) -----> <----- CDC_CMD (REF, 101, PIN_OK, 2, ) <----- CDC_CMD (REF, 101, TRUNK_SET 0, 0047 ) (Send INVITE 0047 to SIP GW, SIP-trunk dial tone) ... CDC_STATE (REF, 101, ESTABLISHED,) -----> CDC_STATE (REF, 101, DIGIT, 6) -----> (Collect digits for billing information) CDC_STATE (REF, 101, DIGIT, 4) -----> digits....871300 (When user stops dialing start billing?) .... CDC_STATE (REF, 101, ACTIVE, ) -----> (Received every 10 sec as a heartbeat) ..... CDC_STATE (REF, 101, DISCONNECT, ) -----> (Conversation disconnected)
When the link to the SIP gateway is established AlphaCom has no knowledge if the user reach a destination or not.
Example 2:<br\> System setup: <br\> SIP call manager <br\> 0047 programmed in AlphaCom as feature 81 Area code with Call Detail Control node set, plus digit collection.<br\>
ABSD programmed with pin code "12" for user "101" <br\>
User "101" dials trunk extension "0047"
AMCD ABSD CDC_STATE (REF, 101, START, 0047) -----> (Starts new billing process) CDC_STATE (REF, 101, DIGIT, 1) -----> (Verify pin digits) CDC_STATE (REF, 101, DIGIT, 2) -----> <----- CDC_CMD (REF, 101, PIN_OK, 2, ) (New dial tone from AMC) <----- CDC_CMD (REF, 101, TRUNK_SET 0, 0047 ) CDC_STATE (REF, 101, DIGIT, 6) -----> (Collect digits for billing information) CDC_STATE (REF, 101, DIGIT, 4) -----> digits....871300 (When user stops dialing start billing?) .... (User stops dialing or press M. SIP INVITE is sent with all collected digits 64871300) ... CDC_STATE (REF, 101, ESTABLISHED,) -----> .... CDC_STATE (REF, 101, ACTIVE, ) -----> (Received every 10 sec as a heartbeat) ..... CDC_STATE (REF, 101, DISCONNECT, ) -----> (Conversation disconnected)
Dependent on the call manager the ESTABLISHED message can arrive during ringing or when the B-side actually lifting the handset.
Failure situations
Illegal pin code
AMCD ABSD CDC_STATE (REF, 101, START, 0047) -----> (Starts new billing process) CDC_STATE (REF, 101, DIGIT, 1) -----> (Verify pin digits) CDC_STATE (REF, 101, DIGIT, 3) -----> <----- CDC_CMD (REF, 101, NOT_OK,, 2, ) User get failure tone and disconnect) CDC_STATE (REF, 101, DISCONNECT, ) -----> (Conversation disconnected) ...
No reply from billing WCSD
AMCD ABSD CDC_STATE (REF, 101, START, 0047) -----> (Starts new billing process) CDC_STATE (REF, 101, DIGIT, 1) -----> (Verify pin digits) CDC_STATE (REF, 101, DIGIT, 2) -----> .... timeout after 3 sec, continue call setup. Throw away all digits buffered so far. (Send INVITE to SIP GW, SIP-trunk dial tone) ... CDC_STATE (REF, 101, ESTABLISHED,) -----> CDC_STATE (REF, 101, DIGIT, 6) -----> (Collect digits for billing information) CDC_STATE (REF, 101, DIGIT, 4) ----->
Illegal number series dialed
AMCD ABSD CDC_STATE (REF, 101, START, 0047) -----> (Starts new billing process) CDC_STATE (REF, 101, DIGIT, 1) -----> (Verify pin digits) CDC_STATE (REF, 101, DIGIT, 2) -----> <----- CDC_CMD (REF, 101, PIN_OK, 2, ) <----- CDC_CMD (REF, 101, TRUNK_SET 0, 0047 ) (Send INVITE 0047 to SIP GW, SIP-trunk dial tone) ... CDC_STATE (REF, 101, ESTABLISHED,) -----> CDC_STATE (REF, 101, DIGIT, 8) -----> CDC_STATE (REF, 101, DIGIT, 2) -----> CDC_STATE (REF, 101, DIGIT, 0) -----> <----- CDC_CMD (REF, 101, DISCONNECT) (Illegal number series 820xxx) (User get failure tone and disconnect) CDC_STATE (REF, 101, DISCONNECT, ) -----> (Conversation disconnected) ....