Actions

Difference between revisions of "Group Call - PTT function"

From Zenitel Wiki

(DAK event)
 
(15 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{A}}
+
{{AI}}
 
This article describes how to configure a DAK key on a station to activate a Group Call when the key is pressed, and cancel the group call when the DAK key is released.
 
This article describes how to configure a DAK key on a station to activate a Group Call when the key is pressed, and cancel the group call when the DAK key is released.
  
In the Event Handler, the event 30 (Station DAK or Input) is triggered when a DAK Key is pressed.
+
==Configure the group to use "Automatic M-key"==
 +
In AlphaPro, select the Group Call, and enable "Automatic M-key". When enabled, there is no need to press the M-key to open the microphone during the group call:
  
The following event will activate group call 85 when the DAK key number 3 (= Subevent 3) is pressed, and cancel when the key is released.
+
[[File:GroupAutoM.png|thumb|500px|Enable "Automatic M-key" for group call 85|none]]
  
 +
== DAK event ==
 +
In the [[Event Handler]], the event 30 (Station Input or Station DAK key) is triggered when a DAK Key is pressed.
  
== Configuration ==
+
The following event will activate group call 85 when the DAK key number 3 (= Subevent 3) is pressed, and cancel when the key is released.
In the following example the volume will be set to level 6 when group call 86 is called from stations in [[UDP group]] 2. The volume is set to level 3 (default) when the group call is ended.
 
 
 
When stations outside UDP group 2 dial group call 86 this event will not be triggered, and the volume will not be altered.
 
  
In [[AlphaPro]], go to [[Exchange_%26_System_%28AlphaPro%29#Events|'''Exchange and System''' -> '''Events''']], press '''Insert''' and create the following event (the action strings can be copy/paste from here into AlphaPro):
+
In [[AlphaPro]], press '''Users & Stations''' button, select a station from the listbox, and press '''Events'''. '''Insert''' a new event with the following properties:
  
{|
+
[[File:GroupAutoM Event.png|thumb|500px|Station 164 presses DAK 3 to activate grop call 85, and cancel upon release|none]]
|-
 
|width="150pt"|'''Event Owner''':
 
|width="400pt"|Stations with UDP: Id: 2
 
|-
 
|'''Event type''': || [[Conversation Outgoing (Event Type)|08 - Conversation Outgoing]]
 
|-
 
|'''Sub event''': || 0
 
|-
 
|'''When change to''': || ON or OFF
 
|-
 
|'''When related to''': || Directory Number, Id: 86
 
|-
 
|'''Action:''' ||  
 
|-
 
|}
 
  
 +
{{Code2|
 
  IF %chg(1,0)
 
  IF %chg(1,0)
tmp 0 "%gns(%2.phy,0)"
+
  $DD L%1.dir L85
LOOP
 
IF %op(%tmp(0),=,0)
 
STOP
 
ENDIF
 
  $VOL N%tmp(0) U6
 
tmp 0 "%gns(%2.phy, %tmp(0))"
 
ENDLOOP
 
stop
 
ENDIF
 
tmp 0 "%gns(%2.phy,0)"
 
LOOP
 
IF %op(%tmp(0),=,0)
 
 
  STOP
 
  STOP
 
  ENDIF
 
  ENDIF
  $VOL N%tmp(0) U3
+
  $C L%1.dir
tmp 0 "%gns(%2.phy, %tmp(0))"
+
}}
ENDLOOP
 
 
 
 
 
In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command:
 
$VOL N%tmp(0) U6
 
  
Volume is set to 3 (U3) when the group call is ended by the command:
+
Note that in the DAK table of station 164, DAK key 3 must be blank.
$VOL N%tmp(0) U3
 
  
U6 and U3 can be changed to other values if required.
 
  
Note that a standard feature exists, which might be a better alternative:
 
Group calls with "[[Groups#Group_Call_Setup_Priority|Setup Priority = Alarm]]" will automatically use the [[Volume and handset override|Volume Override feature]] of the AlphaCom, without any additional configuration required.
 
  
  
[[Category:Applications]]
+
[[Category: AlphaCom Applications]]
 +
[[Category: ICX-AlphaCom Applications]]

Latest revision as of 13:24, 31 May 2022

AI.png

This article describes how to configure a DAK key on a station to activate a Group Call when the key is pressed, and cancel the group call when the DAK key is released.

Configure the group to use "Automatic M-key"

In AlphaPro, select the Group Call, and enable "Automatic M-key". When enabled, there is no need to press the M-key to open the microphone during the group call:

Enable "Automatic M-key" for group call 85

DAK event

In the Event Handler, the event 30 (Station Input or Station DAK key) is triggered when a DAK Key is pressed.

The following event will activate group call 85 when the DAK key number 3 (= Subevent 3) is pressed, and cancel when the key is released.

In AlphaPro, press Users & Stations button, select a station from the listbox, and press Events. Insert a new event with the following properties:

Station 164 presses DAK 3 to activate grop call 85, and cancel upon release

Action commands:

IF %chg(1,0)
$DD L%1.dir L85
STOP
ENDIF
$C L%1.dir 


Note that in the DAK table of station 164, DAK key 3 must be blank.