Search results
Create the page "Pulse" on this wiki! See also the search results found.
- In a Pulse System, when a call is made from a substation, e.g. from a Door Entry, you [[Category: Pulse - Configuration]]1 KB (201 words) - 17:19, 7 March 2019
- ...ed when VS-SDK for Pulse is enabled in the system. See [[VS-IMT VS-SDK for Pulse System Setup]]2 KB (297 words) - 12:03, 23 June 2023
- ...input actions are configured from [[Direct Access Key & Ringlist Settings (Pulse)|Direct Access Key Settings]] (an input behaves like a push button). ...an '''Output''', the output operation is configured from [[Relay Settings (Pulse)|Relay Settings]].3 KB (394 words) - 10:42, 9 February 2023
- * [[IP Station Configuration - Pulse mode]] Note that in '''Pulse mode''' the '''Keyboard configuration''' is not available in the web page.2 KB (313 words) - 17:25, 31 January 2023
- ...lication Protocol (ZAP). This type of project supports the easy setup of a Pulse system: * Upload license to Pulse server9 KB (1,460 words) - 11:36, 29 June 2023
- [[File:Pulse_icon_300px.png|70px|link=:Category:Pulse]]496 bytes (79 words) - 15:29, 26 October 2023
- ...posite state. If a new $SLRC message on the same [[RCO]] arrives while the pulse timer is running, the timer is canceled, and the new message determines the1 KB (221 words) - 14:37, 13 November 2023
- In the examples below 10.5.2.138 is the IP address of the Pulse/SIP station.911 bytes (120 words) - 10:01, 13 September 2019
- [[Image:GSM PULSE2.PNG|thumb|right|500px|The MV-370 GSM Gateway in a PULSE environment]] ...describes the setup of the MV-370 GSM Gateway (item 220 0003 000) in a '''PULSE''' environment.8 KB (1,249 words) - 13:17, 19 May 2020
- * Replace entire system with Vingtor-Stentofon Pulse [[File:Upgrade old systems 5.png|thumb|left|500px|Pulse system]]2 KB (221 words) - 14:24, 5 February 2018
- * ''As from version 4.11.3.1 for Pulse and version 5.1.3.0 for IC-EDGE Virtual I/Os are by default disabled. To en ...t '''RelayTimer_v1.lua''' can be used for this prupose. The script let you pulse a relay of a remote unit for a set time.6 KB (881 words) - 15:22, 15 December 2022
- ===Pulse mode=== ...ation (including IP address and directory number) is configured from the [[Pulse Server]].4 KB (651 words) - 13:16, 24 November 2020
- * [[IP Station Configuration - Pulse mode|Pulse mode]]2 KB (204 words) - 09:52, 16 August 2022
- * '''Pulse Settings are visible but disabled''' : Server IP: IP address of the Pulse Server3 KB (409 words) - 15:02, 3 March 2022
- ====MTN-2289 Two gong signals applied instead of one for group calls in Pulse mode==== ==== MTN-883 IP Flush (Pulse) shows error 484 when dialing and pressing C====4 KB (643 words) - 14:31, 28 February 2019
- * [[IP Station Configuration - Pulse mode|Pulse mode]]2 KB (204 words) - 12:51, 23 June 2023
- * [[IP Station Configuration - Pulse mode|Pulse mode]]2 KB (206 words) - 12:51, 23 June 2023
- ====MTN-2752 The relay did not work on INCA Substation in SIP and Pulse mode==== ====SNOW-330 IP Multicast audio support for Pulse Intercom====5 KB (708 words) - 05:23, 8 March 2022
- {{warn|The PULSE system is obsolete, and is replaced by the [[:category:IC-EDGE System|IC-ED [[File:PulseBox (2).png|thumb|320px|Pulse System]]12 KB (1,790 words) - 09:57, 18 August 2023
- ...icable for the [[IP Flush Master - 1008031000|IP Flush Master]] used in '''Pulse mode''' and '''SIP mode'''. It describes how to configure the station to qu * [[IP Station Configuration - Pulse mode]]2 KB (402 words) - 14:50, 30 June 2022