Difference between revisions of "ATLB - AlphaCom Telephone Line Board"
From Zenitel Wiki
(→Technical Specification) |
(→Connection Boards) |
||
| Line 21: | Line 21: | ||
== Connection Boards == | == Connection Boards == | ||
| − | |||
| − | |||
The standard connection board provides connection for 6 analogue telephones and 6 RCO outputs. | The standard connection board provides connection for 6 analogue telephones and 6 RCO outputs. | ||
| + | [[image:9930202 RS.jpg|thumb|left|500px|Connection Board ATLB]] | ||
| + | <br style="clear:both;" /> | ||
| − | The ATLB provides connection for 6 analogue telephones and 6 RCO outputs. In addition the board provides | + | [[image:Connection Board ProtRing ATLP.jpg|thumb|left|500px|Connection Board Prot/Ring ATLP]] |
| − | protection against heavy transients and a ring voltage generator. This board is used when the subscriber cabling | + | <br style="clear:both;" /> |
| − | may be exposed to heavy transients and should always be used if there are outdoor cables. The ring voltage | + | |
| − | generator is needed when there are several phones in parallel on the same line, or the lines are very long. | + | |
| + | The ATLB provides connection for 6 analogue telephones and 6 RCO outputs. In addition the board provides protection against heavy transients and a ring voltage generator. This board is used when the subscriber cabling may be exposed to heavy transients and should always be used if there are outdoor cables. The ring voltage generator is needed when there are several phones in parallel on the same line, or the lines are very long. | ||
=== AlphaCom E20/E26 === | === AlphaCom E20/E26 === | ||
| − | Telephones and control outputs are connected to a connection | + | Telephones and control outputs are connected to a connection board mounted on the exchange connection field. |
| − | board mounted on the exchange connection field. | ||
| − | Telephone connection board with transient protection (100 9930 | + | Telephone connection board with transient protection (100 9930 202) and subscriber connection cable with filter board (100 9501 031) must be purchased separately. |
| − | 202) and subscriber connection cable with filter board (100 9501 | ||
| − | 031) must be purchased separately. | ||
=== AlphaCom E7 === | === AlphaCom E7 === | ||
Revision as of 13:16, 7 August 2015
Note: The ATLB board is obsolete and is replaced by the ATLB-12 board.
Contents
Highlights
- Is used for 2-wire connection of telephones as stations in an AlphaCom system
- Each board provides 6 telephone connections and 1 voice-switched conversation
- 6 remote control outputs (software configurable activation)
- Hotline function
- DTMF dialing
- R-button detection
- Selectable -48V or -24V battery feed
- 600 ohm or complex impedance hybrid balance
- Line monitoring using resistor in parallel with phone
- Hot-plug in and out of the board
- Red/green/amber LED indicates system status
Additional Documentation
For more documentation please see http://www.zenitel.com/product/product/atlb
Connection Boards
The standard connection board provides connection for 6 analogue telephones and 6 RCO outputs.
The ATLB provides connection for 6 analogue telephones and 6 RCO outputs. In addition the board provides protection against heavy transients and a ring voltage generator. This board is used when the subscriber cabling may be exposed to heavy transients and should always be used if there are outdoor cables. The ring voltage generator is needed when there are several phones in parallel on the same line, or the lines are very long.
AlphaCom E20/E26
Telephones and control outputs are connected to a connection board mounted on the exchange connection field.
Telephone connection board with transient protection (100 9930 202) and subscriber connection cable with filter board (100 9501 031) must be purchased separately.
AlphaCom E7
All telephones are connected by means of pluggable screw terminals on the exchange back-plane.
Note: When the ATLB board is used in AlphaCom E7 only four RCO's are available.
Installation Overview
