Actions

AlphaCom XE demo suitcase - User Guide

From Zenitel Wiki

Revision as of 13:46, 12 August 2010 by Asle (talk) (→‎SIP Station (X-Lite))

AlphaCom XE Demo Suitcase - User Guide

This article describes how to set up and use the AlphaCom XE demo suitcase, item 1009607600.

Demo Suitcase Content

The AlphaCom XE demo suitcase contains the following parts:

  • 1 x AlphaCom XE incl. power adapter, preconfigured
  • 1 x station stand, consisting of one CRM V station, two IP substations and a signaling unit
  • 1 x IP Desktop station
  • 1 x PoE switch with power adaptor
  • 1 x Axis M1011 IP camera incl. power adapter
  • 7 x Ethernet cables
  • 1 x Memory stick with software and documentation

Documentation and software for the demo suitcase is also found on AlphaWiki.

IP Addresses and Directory Numbers

The system is preconfigured with the following IP addresses and numbers:

Device IP address Dirno Name AlphaCom XE, Ethernet port 1 192.168.1.1 AlphaCom XE, Ethernet port 0 165.254.1.5 CRMV 192.168.1.10 101 Control Room IP Desktop 192.168.1.11 102 Office IP sub Euro 192.168.1.12 103 Elevator IP sub US 192.168.1.13 104 Entrance Softclient (PC) 192.168.1.2 105 Softclient SIP Station (e.g. X-Lite on PC) 192.168.1.2 106 SIP Station PC 192.168.1.2 IP Camera 192.168.1.20

The IP stations are set to register by directory number (not by MAC address).

Connection Diagram

  • Connect the IP stations to the PoE ports of the network switch (the 8 leftmost ports).
  • Connect the AlphaCom XE, the IP camera and the PC to the non-PoE ports (the 8 rightmost ports).




How to use the demo suitcase

Sound quality

The stations in the stand are located very close to each other, and it is hard to give a good demo of the AlphaCom XE sound quality. If you going to demo the sound quality it is better to place the IP Desktop station on a remote location, and make calls to or from the IP Desktop.

Call Request

  • Call buttons on the substations make Call Request to the CRM V. Indication on the LED's on the DAK panel.
  • Call Request Forwarding to station 102 is activated by pressing the “Transfer” button on the DAK panel. The transfer status is shown in the LCD display. “Transfer Off” cancels the forwarding.

Door Opening

  • Door open: Press digit 6 on the CRM V while in communication with IP substation 104 to operate the LED in the signaling unit.
  • Door open/closed status: The switch on the signaling unit is connected to an input of the IP substation. The input can be used to indicate door open or closed status on the DAK panel. Door open is indicated by flashing red LED in the DAK panel.

Anti-nuisance

- On the DAK panel press the “Antinuisance” button + station button (e.g. “Elevator” or “Entrance”) to disable calls from that station for 9 seconds. Red LED indicates disabled state. (In real life the station will be disabled for maybe 15 minutes).

Group call and All Call

  • Press “All Call” to make a regular broadcast to all stations. If you demonstrate voice paging (i.e. you are searching for someone), you can answer the paging by pressing 99 on a station (e.g. on the IP desktop).
  • Press “All Call (4gong)” to make an All Call with customized “dingdong” signal. The standard ding-dong is substituted by a wav file playing a gong sequence. This is to demo that the standard dingdong signal can be substituted by any signal.
  • Press “All Call (coco)” to make an All Call with customized pre-warning signal. The standard ding-dong is substituted by a wav file playing a coco sound.
  • Press “Dynamic Grp” to make a dynamic group call. Select members on the DAK panel. Members can be selected and deselected (toggle function). Press “Dynamic Grp” again to dispatch the group call.

Recall

  • Press “Recall (M)”. Press and hold M-key while recording. Release M to listen. Press M to do a new recording, or press 8 to dispatch the message as an All Call.
  • Press “Recall”. Start talking (no M-key) and press C when finished to dispatch the message. Alternative: Lift the handset, press “Recall”, talk, hang up.

Emergency group call with Acknowledgement

This is a group call were all recipients have to verify that they have received the group call message by dialing an acknowledgement code.

  • Press “Emerg.Grp”. A group call is activated, and the red LED’s of the recipients will be lit in the DAK panel. The receiving stations must dial 9590 to acknowledge. LED status will change to green. Press “Clear” to reset all LED’s in the DK panel.

Voice alarm distribution

  • Press “Fire”, “Evacuate” or “Baggage” to distribute prerecorded voice message to all stations at full volume. Press “Message Off” to stop message.

Integration with CCTV

  • The IP camera is associated with station 104. When station 104 makes a call the picture will automatically appear on the PC running the Milestone software. How to install and set up the Milestone software is described in a separate document.

Voice Activity Detection (VAD)

  • Voice Activity on station 104 is indicated on the DAK Panel as Call Request with low priority (30). Camera will automatically appear on the Milestone PC. Note: VAD must be enabled in the IP substation 104 (192.169.1.13). Log on to the station using Internet Explorer, select Advanced > VAD, and set VAD Status to Enabled. Adjust the sensitivity by changing Minimum Amplitude.

Softclient

- The demo suitcase is prepared for STENTOFON Softclient on directory number 105. The PC should be assigned IP address 192.168.1.2. Install the Softclient on your PC. In File > Preferences set AlphaCom IP address = 192.168.1.1 and AlphaCom ID (MAC or Dirno) = 105.

SIP Station (X-Lite)

  • The demo suitcase is prepared for SIP Station on directory number 106. The PC should be assigned IP address 192.168.1.2. Install the X-Lite software on your PC. Create a SIP account with the following settings: Display Name = Any text. User name = 106. Domain = 192.168.1.1.
Retrieved from "https://wiki.zenitel.com/w/index.php?title=AlphaCom_XE_demo_suitcase_-_User_Guide&oldid=99949"