View source for GSM Gateway (Pulse)

{{P}}
[[Image:GSM PULSE2.PNG|thumb|right|500px|The MV-370 GSM Gateway in a PULSE environment]] 
This article describes the setup of the MV-370 GSM Gateway (item 220 0003 000) in a '''PULSE''' environment.

==Prerequisites ==
* A Pulse System with a [[Pulse Server]] already installed
* SIM card (mini-SIM size) for the gateway. You need to know the phone number and the PIN code for the SIM card.

== PULSE Configuration ==

===Install license===
Before a SIP Gateway Account can be created on the Pulse Server, you need to obtain the '''Pulse Telephone Gateway''' license:
* 1009662001: Pulse-Server-TelTrunk (requires that the Pulse Server is a [[:Category:Stations#Turbine_stations|Turbine station]] running firmware 4.2 and higher), or
* 1009643121: Pulse telephone gateway license (supported by all platforms ([[:Category:Stations#INCA_stations|INCA stations]] and [[:Category:Stations#Turbine_stations|Turbine stations]]), and by all software versions)

* To install the license, log on to the Pulse Server, and under '''Station Administration''' > '''Licensing''' insert the License Key:
[[File:PulseSIPgwLicense.PNG|thumb|left|500px|Successfully installed SIP gateway license]]
<br style="clear:both;" />

=== Create the SIP Gateway account ===
On the Pulse Server, select '''Server Management''' > '''Server Configuration''' > '''Directory Settings'''. 
[[Image:PulseSIPGatewayAddAccount.PNG|thumb|500px|left|Adding a SIP Gateway account]]
<br style="clear:both;" />

Set the following values:
* '''Directory Number''': 0 (This is the number to dial to get access the telephone line. Other number can be used)
* '''Name''': <name of your choice>
* '''Profile: Default'''
* '''Password''': Normally leave this field blank. When a password is entered, the SIP gateway must register using this password.
Click '''Add''', followed by '''Save'''.

Note: The "Gateways" option will only appear on the Pulse Server if there is a valid license installed.
<br style="clear:both;" />

== GSM Gateway Configuration  ==
'''Important:''' If you have a SIM card with PIN code activated, '''DO&nbsp;NOT'''&nbsp;insert the SIM card yet. 


=== Load Factory Default values ===
The GSM Gateway comes with default network parameters (factory default parameters). The default IP address is '''192.168.0.100'''.

You can load factory network parameters and reset the username and password to its default settings (username: '''voip''', password: '''1234''') by following these steps:

# Press and hold the button SW1 located at the bottom of the unit (you have to remove the lid) for about 7-8 seconds
# Wait for the "Mobile" and "LAN" leds to start blinking

[[File:GSM FactoryDef.PNG|left|500px|thumb|Set default IP Address: Press SW1 for 7-8 seconds]]
<br style="clear:both;" />


* The GSM Gateway will now get the IP address '''192.168.0.100''', subnet mask 255.255.255.0.

===Accessing the gateway ===
* Change the IP address of your '''PC to 192.168.0.99''', subnet mask 255.255.255.0.
* Connect the LAN port of the PC to the Ethernet port of the GSM Gateway.
* Start your Web Browser and type 192.168.0.100 in the URL field.
* Type in username '''voip''' and password '''1234'''. (Case-sensitive!)

[[File:GSM accessing.PNG|left|500px|thumb|Accessing the gateway]]
<br style="clear:both;" />


*The Home page of the Web Interface will appear: 

[[File:GSM Home.PNG|thumb|left|500px|Homepage of the GSM Gateway]]
<br style="clear:both;" />

===Network Configuration===

To change the IP address of the GSM gateway, go to '''Network''' > '''WAN Settings''', and enter:
*'''IP Type''': Fixed IP 
*'''Master IP''': The IP address of this gateway. Must be in the IP address range of the subnet for the PULSE system 
*'''Mask''': Subnet mask for the gateway. Other parameters are optional.
* Press '''Submit''', then '''Save'''. The gateway will restart.

[[File:GSM WAN.PNG|thumb|left|500px|Network settings]]
<br style="clear:both;" />

After having changed the IP Address of the gateway, follow these steps to re-access the gateway:
* Change the IP address of your PC to match the new network settings of the gateway. The PC and Gateway must be on the same subnet.
* Re-access the Gateway by typing the new assigned IP address in the URL field of your web browser.

=== SIP Parameters ===
To define the SIP settings, go to '''SIP Settings''' -> '''Service Domain''':

* '''Active''' = ON
*'''Display Name:''' Any text 
*'''User Name''': Enter the directory number used to access the gateway. This number must be identical to the number entered in the PULSE Server. 
*'''Proxy Server''': Enter the IP address of the PULSE Server
* Press '''Submit''', then '''Save'''. The gateway will restart.

[[File:GSM SIPRegistered.PNG|thumb|left|500px|SIP Parameters]]
<br style="clear:both;" />

* '''Status''' = Registered: Shows that the gateway is successfully registered to the PULSE server.

=== Mobile Settings ===
Go to '''Mobile''' > '''Settings''' and define the following parameters:

* '''SIP From''' = Tel/User (Standard)
* '''Mobile PIN Code''' = ON. Code: Enter the PIN code for the SIM card. Confirmed: Enter the PIN code again.

[[File:GSM MobSetting.PNG|thumb|left|500px|Mobile settings]]
<br style="clear:both;" /> 

The SIM card can now be inserted. The gateway uses Standard (Mini) SIM card (15x25mm).
[[File:GSM SIM Placement.PNG|thumb|left|300px|SIM card placement]]
<br style="clear:both;" />

After the SIM card is inserted, you can check that the gateway is successfully registered to the GSM network in '''Mobile''' > '''Status'''.

Some parameters to look for are:
* '''Operator''' = The telecom provider
* '''Signal Quality''' = Shows the signal strength. The signal should be in the range of 10 - 31.

[[File:GSM Registered.PNG|thumb|left|500px|Gateway successfully registered to the GSM network]]
<br style="clear:both;" />

If these parameters does not show, your gateway is not registered to the GSM network. Check that SIM card is properly inserted, and that the PIN code is correctly entered. 

'''TIP''': Try the SIM card in a regular mobile phone.

=== Configure outgoing calls to the GSM network ===
To automatically dial an external phone number when gateway is accessed, go to '''Route''' > '''Lan To Mobile Settings'''.

On item 0, enter:
* '''URL''' = *
* '''Call Num''' = <external phone number to dial>

[[File:GSM OutgoingCall.PNG|thumb|left|500px|Outgoing calls routed to a fixed telephone number]]
<br style="clear:both;" />


If '''Call Num''' instead is set to "*", there will be 2-stage dialing. I.e. you will get a second dial tone after having dialed "0", and the gateway will wait for further digits.

=== Configure incoming calls from the GSM network ===
'''Alternative 1''': Route incoming calls to a predefined number.

Select '''Route > Mobile to LAN Settings''', and set:
:*'''CID''' = *
:*'''URL''' = <intercom number>

[[File:GSM IncomingCall2.PNG|left|thumb|500px|Incoming calls are routed to station number 12]]
<br style="clear:both;" />


'''Alternative 2''': There will be a second dial-tone presented on incoming calls. The user must dial the intercom number. The dialing can be terminated by '#', or alternatively one can wait for 5 seconds and the call will be established.  

Select '''Route > Mobile to LAN Settings''', and set:
:*'''CID''' = *
:*'''URL''' = *

[[File:GSM IncomingCall.PNG|left|thumb|500px|Selective incoming call]]
<br style="clear:both;" />


=== DTMF Input from outside line ===
During a conversation between a Pulse station and a telephone, the telephone operator can activate an output (e.g. trigger a relay for door opening) in the Pulse System by pressing a digit on the phone. 

To enable digit actions from the telephone line during conversation, go to set '''SIP Settings''' > '''DTMF Setting''', and enable "SIP INFO": 

[[File:GSM SIPINFO.PNG|left|thumb|500px|Set DTMF by 'SIP INFO']]
<br style="clear:both;" />

=== Software Upgrade ===
To do a software upgrade, go to '''Update''' > '''New Firmware''':

# Select the firmware code type "Risc".
# Click the '''Browse''' button and navigate to the file you want to download
# Click the '''Submit''' button

[[File:GSM SWupgrade.PNG|left|thumb|500px|Software upgrade]]
<br style="clear:both;" />


After a software upgrade you must load default settings by selecting '''Update''' > '''Default Settings''' > '''Default'''.


== Call multiple phone numbers in sequence ==
{{Obs|'''This feature is currently not supported!''' }}
The Ringlist of the calling station can be used to call multiple phone numbers in sequence. If the first number doesn't answer within a preset time, the call will be made to the second number, and so on. Intercom stations can also be included in the sequence. You can have upto 30 numbers in the ring list. Thee is also an option to loop the list, so the sequence can be repeated an preset number of times.
Call scenario examples:
# Call to an Intercom station > Phone number 1 > Phone number 2 in sequence, or
# Call Phone number 1 > Phone number 2 > Phone number 3 in sequence 

{{note|
*''The Pulse server must be a [[:Category:Stations#Turbine_stations|Turbine device]], running software version 4.9.3.0 or later''
*''A Pulse Enterprise license 1009660002 is required (TelTrunk license is not required!)'' }}

Log on to the Pulse Server and install an Enterprise license. This will enable '''Pulse Trunking''' feature, which is required to achieve sequencial calls:
[[File:PulseEnterprise.PNG|thumb|left|500px|Successfully installed Enterprise license]]
<br style="clear:both;" />

In the Pulse Server, '''Server Management''' > '''Server Configuration''' > '''Directory Settings''', go to the '''Pulse Trunk''' section and define the number range for the phone numbers to call, and the IP Address of the GSM gateway:
[[File:PulseTrunkPhoneNo.PNG|thumb|left|500px|Numbers from 90000000 to 99999999 will be routed to the GSM gateway 10.5.101.45]]
<br style="clear:both;" />
It must be the same number of digits in the '''Directory Start''' and the '''Directory Stop''' field.

At the calling station, '''SIP Configuration''' > '''Direct Access Key Settings''', select '''Ringlist 1''', and configure the phone numbers to call in sequence, and the time between each call:
[[File:PulseCallPhoneNo.PNG|thumb|left|500px|Call button (DAK 1) will call three different phone numbers in sequence at 25 seconds interval]]
<br style="clear:both;" />

In the GSM Gateway, configure outgoing calls to use "enbloc" (one-stage) dialing. Go to '''Route''' > '''Lan To Mobile Settings'''.

On item 0, enter:
* '''URL''' = *
* '''Call Num''' = #

[[File:GSM EnblocDial.PNG|thumb|left|500px|Outgoing calls using Enbloc dialing]]
<br style="clear:both;" />




[[Category:Pulse - Telephone Gateways]]
[[Category: IC-EDGE Integrations]]