View source for Display Setup Menu (IP Stations)

{{AEIPS}}
When the IP Master Station is not configured or not registered to a server, an offline configuration menu is available. The offline menu can be used to configure the station and is navigated with the 4 buttons below the display. The button on the left is used as a '''Select''' or '''Ok''' button as shown in the display, while the button on the right is used as a '''Back''' button. The two buttons in the middle are used to navigate up or down according to the arrows. When configuring IP settings, the '''M''' key is used to  insert a "." (dot) and the '''right-middle button''' is used to delete a character.

==Main menu==
*Press the '''Setup''' button on the left, and enter the default password '''1851''', and press '''OK'''.
[[File:Display NotConfigured.png|left|thumb|300px]]
<br style="clear:both;" />

Use the two arrow buttons in the middle to navigate through the menu options. 
[[File:Display MainMenu.png|left|thumb|300px]]
<br style="clear:both;" />
Press the '''Sel''' button on the left to select the menu option and the '''Ok''' button to confirm data entered. When entering data, the left-arrow is used for deleting characters.

==Station info==
This shows the station MAC address and IP address, the configured Server address and Software version.
[[File:Display StationInfoMenu.png|left|thumb|300px]]
<br style="clear:both;" />

==IP settings==
Choose between DHCP and STATIC IP address. If STATIC is chosen, it is possible to configure the IP address, mask and gateway. Use the '''M-key''' to insert a "." (dot) 
[[File:IP Station Config 5.PNG|left|thumb|300px]]
<br style="clear:both;" />

==Station mode==
In this menu you select the mode of operation, and which type of server the station should register to.

There are three options:
[[File:Display StationMode.png|thumb|left|300px|Software version 02.11.3.0 and older]]
<br style="clear:both;" />
[[File:DIsplay StationModeV2.png|thumb|left|300px|Software version 6.x.x.x]]
<br style="clear:both;" />

The default mode of operation is '''Edge'''.

===ICX-AlphaCom mode===
When the station is set to AlphaCom (or ICX-AlphaCom) mode, a new menu '''AMC Settings (ICX Settings)''' becomes available. Here you enter the IP address of the ICX-AlphaCom server and the directory number of the station. 
[[File:Display AMC SettingsMenu.png|thumb|left|300px|Software version 02.11.3.0 and older]]
<br style="clear:both;" />
[[File:Display ICX SettingsMenuV2.png|thumb|left|300px|Software version 6.x.x.x]]
<br style="clear:both;" />

===Edge mode===
When the station is set to Edge mode, no further configuration is required in the station. All configuration (including IP address and directory number) is configured from the [[Edge Controller]].

===SIP mode===
When the station is set to SIP mode, go to the menu '''SIP Settings''' to enter the IP address of the SIP server and the SIP ID (directory number) of the station. 
[[File:Display SIP SettingsMenu.png|thumb|left|300px]]
<br style="clear:both;" />

==Load defaults==
This will load the factory default settings. All existing settings will be deleted and default values will be loaded. Default IP address is '''169.254.1.100'''.
*Press the '''Sel''' button to load the default settings.
[[File:IP Station Config 7.PNG|thumb|left|300px]]
<br style="clear:both;" />

==Restart==
This will restart the station. 
*Press the Sel button to restart the station.
 Restart the station to apply new settings
[[File:IP Station Config 8.PNG|thumb|left|300px]]
<br style="clear:both;" />

== Related articles ==
* [[Password (IP Stations)|Changing the password for accessing the display menu]]

[[Category: INCA - Restore Factory Defaults and Software Upgrade]]
[[Category: Turbine - Restore Factory Defaults and Software Upgrade]]
[[Category: INCA Station Configuration Guide]]
[[Category: Turbine Configuration]]
[[Category: IC-EDGE Configuration]]
[[Category: SIP intercom - Configuration]]