View source for SIP Intercom - Web Interface

{{S}}
[[File:SIP User diagram.PNG|thumb|400px|SIP based System]]
Zenitel IP Devices can be configured to operate in ''SIP Mode'', and can be used with any SIP based iPBX or Call Manager.

The devcies are easy to install and configure. They can be configured using a standard web browser (like Firefox or Chrome), or one can use the dedicated [[IMT|Intercom Management Tool IMT]]. This article describes configuration using the Web interface.

=Getting Started= 
Main steps to get the device registered to a SIP server:

#[[Logging into an IP Station|Log on to the station]]
#[[Main Settings (IP Stations)|Main Settings]]: Go to '''Station Main''' > '''Main Settings''' and set "Station Mode" = '''Use SIP''', and enter the IP Settings.
#[[Account Settings (SIP)|Account Settings]]: Select '''SIP Configuration''' > '''SIP Settings''' and enter as a minimum '''Display Name''', '''Directory Number''', '''Server Domain''' and '''Authentication User Name'''.
#[[Direct Access Key & Ringlist Settings (SIP)|Call Buttons (DAK keys)]]:  Select '''SIP Configuration''' > '''Direct Access Key Settings'''.
##[[OLED Labels]]: How to configure the OLED display used for labeling the call buttons in the station models [[TCIV-5+]], [[TCIS-4]] and [[TCIS-5]]
##[[Address Book]]: How to configure and maintain the Address Book used in the station models [[TCIV-6+]], [[TCIS-6]] and [[TCIV-6]]

<br>

=The station web interface=
==Station Main==

*'''Station Information''' page shows current status and information about the station, suuch as firmware version and IP Address
*[[Main Settings (IP Stations)|Main Settings]]: Here the mode of operation is set, the network settings, and the model type.


==SIP Configuration==
===SIP Settings===

*[[Account Settings (SIP)|Account Settings]]: Configure relevant parameters for the SIP account
*[[Call Settings (SIP)|Call Settings]]: A number of Call related parameters are available

===Audio Settings===
[[Audio Settings (Devices)|Audio Settings]]: A number of Audio related parameters are available

===Direct Access Key & Ringlist Settings===

*'''Direct Access Keys (DAK)''' are the Call Buttons or speed-dial buttons you find on most intercom stations.
*'''Ring List''' is used to configure Call Escalation (i.e. forwarding of unattended calls), and for Parallel Ringing.

To configure Call Buttons and Ring List, see [[Direct Access Key & Ringlist Settings (SIP)]]

===Relay/Output Settings===
All IP Intercom stations (execpt the desktop models) have a built-in relay which can be used for door opening, call indication lamp etc. The relay can be controlled by a DTMF digit, or by a number of different call events and station statuses. 

For details about relay configuration, see [[Relay Settings (SIP)|Relay Settings]]

===Time Settings===
The user is able to configure time by either enabling NTP and specifying NTP server, or setting up time manually. On Master stations with display the configured time is shown on display. 

See [[Time Settings (SIP)|Time Settings]] for details.

===I/O Settings===
The [[:Category:Stations#Turbine_stations|Turbine stations]] have 6 I/O's which can be used as Inputs or Outputs. By default all I/O's are set as Inputs. 

For details about configuration of inputs and outputs, see [[I/O Settings (SIP)|I/O Settings]].

===Frontboard Mapping [Turbine only]===
When making customized stations based on the Turbine Frontboard, it is possible from the station web interface to define DAK actions and LED behavior. 
This is supported when front board type is set to TCIS 1/2/3 and TCIV 1/2/3, and the station operates in Pulse or SIP mode.

For more details, see [[Button and LED configuration for customized stations (SIP)]]

===RTSP and ONVIF (Non video intercoms)===
'''RTSP Settings''': see [[RTSP_Settings#Non-Video_Intercoms|RTSP Settings for Non-Video Intercoms]]

'''ONVIF Settings''': see [[ONVIF_Settings#Non_Video_Intercoms|ONVIF Settings for Non-Video Intercoms]]

===Video Settings===
See article [[Video Settings]] on how to set parameters for the camera and stream options.

===Advanced Video Settings===
'''RTSP Settings''': see [[RTSP_Settings#Video_Intercoms|RTSP Settings for Video Intercoms]]

'''ONVIF Settings''': see [[ONVIF_Settings#Video_Intercoms|ONVIF Settings for Video Intercoms]]

===Scripts [Turbine only]===
'''Scripts''' (Virtual I/O) is a feature for activating scripts on station events. The supported script languages are Lua and other shell scripting languages. This can be used for example to execute scripts towards other systems, e.g. access control systems, triggered by a DTMF digit. These scripts can be uploaded and configured via the menu options:

*Script Upload
*Script Configuration
*Script Events

The Scripting feature is supported on [[:Category:Stations#Turbine_stations|Turbine stations]] only.

For more details, see [[Virtual I/O (SIP)|Virtual I/O]]

===Audio Messages [Turbine only]===
Prerecorded audio files can be uploaded to a [[:Category:Stations#Turbine_stations|Turbine IP Station]], and the audio messages can be triggered by various events occuring on the station. The audio message files are uploaded from the station webinterface or from the [[IMT|VS-IMT tool]]. 

See [[Audio Messaging (SIP)|Audio Messaging]] for more details.

===Language Settings ===
In some station models it is possible to change the language of the display texts. This does not affect the texts in the web server interface. See [[Language Settings (SIP)|Language Settings]] for details.

===Multicast Paging===
'''Multicast Paging''' enables IP intercom stations in SIP mode to receive VoIP audio as multicast paging from 3rd party iPBX (e.g. Asterisk). The feature is supported by both [[:Category:Stations#INCA_stations|INCA stations]] and [[:Category:Stations#Turbine_stations|Turbine stations]]. Up to 10 different Multicast paging groups can be defined. 

See [[Multicast Paging (Edge/SIP)]] for details.
<br>

===Certificates===
A HTTPS certificate can be uploaded to the device. See [[Uploading HTTPS certificate]] for details.

Certificate settings have been moved to [[SIP_Intercom_-_Web_Interface#Advanced_Network_Settings|Advanced Network Settings tab]] as from version 9.0.3.0.

<br>

==Station Administration==
===Change Password===
The password for web access and for accessing the display setup menus can be changed, see [[Password (IP Stations)]].

===Manual Upgrade===
The software in the stations can be upgraded via the web interface of the station. The procedure is slighty different depending on the type of station:

*[[:Category:Stations#Turbine_stations|Turbine devices]]:  [[Turbine Software Upgrade|Upgrade procedure]]
*[[:Category:Stations#INCA_stations|INCA devices]]: [[INCA Station Software upgrade|Upgrade procedure]]

===Backup and Restore===
From the web interface of the station it is possible to backup and restore the configuration data. See [[Backup and Restore (IP Stations)|Backup and Restore]] for more information.

===Logging===
Logs can be useful for debugging and troubleshooting purposes. See [[Logging - IP Stations]] on how to enable and collect logs.

===Keyboard [INCA only]===
On the [[:Category:Stations#INCA_stations|INCA Stations]] there is an option to set Keyboard Type. This is typically used for the [[IP Substation Kit - 1008090200|IP Substation kit]] or the [[IP Master Station Kit - 1008093000|IP Master kit]] when building customized stations. See [[Keyboard Settings]] for further details.

<br>

==Advanced SIP==
===Updates===
IP stations may be set up to automatically poll configuration from a TFTP server. The IP address of this TFTP server can be obtained using DHCP procedures or be manually configured. See [[TFTP Provisioning (SIP)|TFTP Provisioning]] for more information.

===Tone test===
The '''tone test''' is designed to check whether the microphone and loudspeaker is working by playing a tone and detecting the sound pressure level. If the sound pressure level is below a chosen threshold the test fails. The result of the tone test is reported using SNMP traps, which must be turned on in the [[SNMP in IP Stations|SNMP configuration]]. 

For configuration of the Tone test, see [[Tone Test (IP Stations)]]

===Web Call===
Webcall makes it possible to establish a call directly from the station web. See [[Web Call and HTTP commands (SIP)|Web Call]] for more information.

<br>

=== Whitelist ===
TBA

<br>

=== Specific Settings ===
* '''TADM''': No information available
* '''KALC''': No information available
* '''Basic SRV''':  No information available
* '''Device Profile''':  No information available

<br>

==Advanced Network Settings==
===SNMP===
A set of SNMP functions are available in the IP station. SNMP (Simple Network Management Protocol) is a protocol for centralizing the management of devices in IP networks.

See [[SNMP in IP Stations]] for futher information.

===802.1X===
IEEE 802.1X is an IEEE Standard for port-based Network Access Control (PNAC). It provides an authentication mechanism to devices wishing to attach to a LAN, either establishing a point-to-point connection or preventing it if authentication fails. For details on configuration, see [[IEEE 802.1X]].

<br>

=== HTTPS Certificate ===
A HTTPS certificate can be uploaded to the device. See [[Uploading HTTPS certificate]] for details.

=== SIP Certificates ===

A certificate can be uploaded to the Turbine station for use with SIP TLS. See [[Upload SIP Certificate]] for details.

===Firewall===
All IP Stations have an embedded firewall. See [[Firewall (IP Stations)|Firewall]] for details.

===VLAN ===
'''VLAN Tagging''' is the practice of inserting a '''VLAN ID''' into a packet header in order to identify which '''VLAN''' (Virtual Local Area Network) the packet belongs to. More specifically, switches use the '''VLAN ID''' to determine which port(s), or interface(s), to send a broadcast packet to.

For details on configuration, see [[VLAN Settings (Devices)]].

[[Category: INCA Station Configuration Guide]]
[[Category: SIP intercom - Configuration]]
[[Category: Turbine Configuration]]