View source for ELSII-10PM

{{AEIS}}
ELSII-10PM is a bi-directional network projector loudspeaker with a built-in 10W amplifier and microphone. The microphone is used e.g. for talkback and for [[Automatic Volume Control (AVC)|Automatic Volume Control]].  
[[File:Projector speaker-ELSII-10PM 2000x2000px.jpg|thumb|350px|Projector Loudspeaker<br>(1023302340)]]

== HowTo video==
<div style="text-align:left;"> <youtube width="300" height="180">HLIiJm8m2Cs</youtube>  </div>
<br><br>

== Installation ==
The ELSII-10PM comes with an external junction box that houses the TKIS-2 kit and microphone.
# Remove the cover of the junction box.
# Pass the network cable through the cable gland for the RJ45 port.
# Terminate the cable end with an RJ45 connector.
# Plug the network cable connector into the RJ45 port of the TKIS-2 kit.
# Optional - Check that the microphone and speaker are connected.
# Replace the cover of the junction box.


[[Image:10PM Install.PNG|thumb|left|700px|Speaker installation]]
<br style="clear:both;" />

{{note|Installation of the speaker must be done using shielded Ethernet cables with grounding at the switch end.}}

== Configuration ==
The loudspeaker can operate in three different modes, depending on what kind of server it should register to. Choose one of the links below according to what mode you need to configure.
* [[Starting Up Turbine Station|Starting up]]
* [[IP Station Configuration - ICX-AlphaCom mode|ICX-AlphaCom mode]]
* [[Adding station to existing system (Edge)|Edge mode]]
* [[SIP Intercom - Web Interface|SIP mode]]

== Conversation mode ==
To prevent acoustic echo during two-way communication with the speaker, the speaker will be in "PTT-mode" (Simplex mode). This means that the operator needs to press the M-key or (or the *-key on an ITSV phone) to talk, and release the M-key (or press the #-key) to listen. This mode of operation is default when the IP speaker is used in Edge or SIP mode. When used in ICX-AlphaCom mode, one have to [[PTT mode - IP Speakers|configure "PTT-mode"]].

== Disabling the microphone ==
The microphone can be disabled by [[Logging into an Zenitel IP Device|logging into the web interface]] of the loudspeaker, enable "Advanced Configuration" mode, and navigate to '''Audio Settings''' > '''Audio Inputs''', and set '''Internal Microphone''' = ''Not Connected''.
(This option is available as from firmware 7.5.3.1).

Talkback and Automatic Volume Control will no longer work when the microphone is disabled.

== ONVIF support ==
Zenitel IP Speakers support the [[ONVIF_Settings|ONVIF protocol]].

'''ONVIF Profile S:''' <br>
The IP Speaker has ONVIF "profile S" support and capabilities, similar to video devices. This enables e.g. an ONVIF VMS Client to monitor the built-in microphone if the IP Speaker.

The IP Speaker is streaming video that shows JPEG image of the Zenitel logo, using 1 FPS (Frame Per Second) to provide compatibility with various VMS systems. Maximum RTSP stream count is 1 microphone audio, 1 JPEG video and 1 backchannel audio. RTSP PLAY will respond with 453 "Not Enough Bandwith" if that limit is breached.
* The IP Speaker is using '''TCP port 8095''' for ONVIF
* HTTP tunneling is done over RTSP '''TCP port 554'''

'''ONVIF Audio Backchannel:'''<br>
The IP Speaker supports the ONVIF audio backchannel. This enables an ONVIF VMS Client to send audio to the IP Speaker.

[[ONVIF_Settings#Non-Video_Intercoms|ONVIF configuration]] is done from the Web interface of the IP Speaker.

== Restore Factory Defaults and Software Upgrade ==
The ELSII-10PM IP Speaker has a Turbine kit [[TKIS-2]] inside.
* [[TKIS Restore Factory Defaults|Restore Factory Defaults]]
* [[Turbine Software Upgrade|Upgrade via the station web interface]]
* [[IMT - Discover & Upgrade|Upgrade using the IMT tool]]
* [[Automatic Software Upgrade|Automatic Software Upgrade (SIP mode only)]]
* [[:Category:IMX28 Release notes|Software Release Notes]]

== Connectors, Indicators and Dimensions ==
The ELSII-10PM IP Speaker has a Turbine kit [[TKIS-2]] inside.
* [[Turbine Compact series board connectors|Device Connections]]
* [[TKIS Indication LEDs|Station Indication LEDs]]
* [[Speaker Dimensions & Mounting Instructions|Dimensions]]

== Software Requirements ==
If the IP Speaker is used with an AlphaCom XE server, the server must have minimum version 11.2.3.7.

== Related Information ==
* [http://www.zenitel.com/product/elsii-10pm Additional Documentation on Zenitel.com]

[[Category: Turbine]]
[[Category: IP Speakers]]