View source for Philips M100

{{A}}
[[File:M100int.png|thumb|800px]]

=Software Requirements=
==AlphaCom==
The AMC-IP board must have software version 10.20 or higher. Latest software version is always recommended. The latest version for AlphaCom can be [[Downloads#AlphaCom_.28AMC-IP.29_software|downloaded here]]. <br/>
The AMC-IP software includes the following software routines:
* The software daemon (M100d) which is running the M100 format with the AlphaCom XE main software.
* The software daemon AMCd which is running the AlphaCom XE Main Software
* The embedded web server which is used to configure AMCd and M100d (AlphaWeb).
The latest supported AMC version is 11.2.3.11

==M100==

<u>'''Supported SW:'''</u>
 6U Computer Card LBB 7103/07: SW LBB 7216/83
 3U Computer Card LBB 7103/05: SW LBB 7216/83
 FC Card LBB 7103/13:          SW LBB 7202/28

=Programming Tools=
==AlphaCom==
The programming tool for AlphaCom is AlphaPro software version 10.28 or higher. <br/>
Download the latest [[Downloads#AlphaPro|version here]]. <br/>
AlphaPro is used to identify M100 modules as nodes in the AlphaNet and to configure the AGA audio routing.

==M100==
The programming tool for M100 is SysMain software version 3.0. It is available on request from alphasupport@zenitel.com.

=Audio Link Interface=
[[File:M100Int_1.PNG|thumb|left|500px]]
<br style="clear:both;" />
The Audio Link Interface Unit is powered from the M100 module. Solder a 3-wire power cable to the three solder studs labeled '''+5V, 0V''' (GND), and '''-5V''' on the M100 backplane. Connect the other free end of the cable to a 3-way plug-in screw terminal that connects to the receptor labeled '''-5V GND +5V''' at the back of the Audio Link Interface Unit.
[[File:M100Int_2.PNG|thumb|left|500px]]
<br style="clear:both;" />

=Data Connection=
==AlphaCom==
Use a crossed RS232 cable with male 9-pin D-sub connectors at each end to connect the AlphaCom XE7 serial '''Port 0''' to the Audio Link Interface connector labeled '''AlphaCom RS232'''.

==M100==
The M100 system	communicates via optical fiber cables. The opto	cable (LBB 7103/61) connects from the M100 Computer Card (LBB 7103/05) to the Audio Link Interface Unit. On the Computer Card, connect the opto cable to the connector labeled '''Module 1''' (assuming that the M100 is a single-module system). The other end of the opto cable connects to the receptors labeled '''M100 Serial - Opto''' at the back of the Audio Link Interface Unit.
[[File:M100Int_3.PNG|thumb|left|500px]]
<br style="clear:both;" />

=Audio Connection=
==AlphaCom==


===Group Call & 8 Audio Channels===
To connect 8-channel Group Call audio for AlphaCom:
* Cut off one connector on three 8-pair flat cables.
* Connect the free ends to nine 4-way plug-in screw terminals according to table 1.
[[File:M100Int_6.PNG|thumb|left|300px]]
<br style="clear:both;" />
* Connect the plugs to the corresponding connectors at the back of the AlphaCom XE7 Audio Server according to table 1.
* Connect the other end of the cables to the connectors at the back of the Audio Link Interface labeled '''AlphaCom Audio 1''' to '''3'''.
[[File:M100Int_4.PNG|thumb|left|500px]]
<br style="clear:both;" />
[[File:M100Int 8.PNG|thumb|left|500px|Table 1]]
<br style="clear:both;" />

===Group Call & 16 Audio Channels===
To connect 16-channel Group Call audio for AlphaCom:
* Cut off one connector	on six 8-pair flat cables.
* Connect the free ends to seventeen 4-way plug-in screw terminals according to tables 1 and 2.
* Connect the plugs to the corresponding connectors at the back of the AlphaCom XE7 Audio Server according to tables 1 and 2.
* Connect the other end of the cables to the connectors at the back of the Audio Link Interface labeled '''AlphaCom Audio 1''' to '''6'''.
[[File:M100Int_5.PNG|thumb|left|500px]]
<br style="clear:both;" />
[[File:M100Int 9.PNG|thumb|left|500px|Table 2]]
<br style="clear:both;" />

==M100==
===Group Call===
To connect Group Call audio for M100:
* Connect a 20-core ribbon cable to the free connector labeled '''PGM''' at the back of the M100 module. 
** Only the Group Call channel is transmitted and not the Program Distribution channels.
* Connect the other end to the connector at the back of the Audio Link Interface labeled '''M100 Group Call'''.

===8 audio channels - 1 LUS board===
To connect 8-channel audio for M100:
* Connect a 32-core ribbon cable to the free connector labeled '''LU8-9''' at the back of the M100 module.
* Connect the other end to the connector at the back of the Audio Link Interface labeled '''M100 LU9 & LU8'''.

===16 audio channels - 2 LUS boards===
To connect 16-channel audio for M100:
* Connect a 16-core ribbon cable to the free connector labeled '''LUS/LU9''' at the back of the M100 module.
* Connect the other end to the connector at the back of the Audio Link Interface labeled '''M100 LU9'''.
[[File:M100Int_7.PNG|thumb|left|500px]]
<br style="clear:both;" />

=Programming in SysMain (M100)=
==Installation==
Install and start SysMain on your PC.

==Getting Started for New M100 System==
* Select '''File -> New'''
** A setup wizard will start
* Click '''Next'''
[[File:M100Int_10.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Select '''S-72 Stand-alone Exchange''' and click '''Next'''
[[File:M100Int_11.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Select the type of system of your choice. In this example '''Hospital System''' is selected.
* Click '''Next'''
[[File:M100Int_12.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Select '''Use default tables''' and click '''OK'''

==Setting system parameters==
After setup is completed, the Update system information window automatically opens:
[[File:M100Int_13.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Set '''No. of modules''' to '''2'''.
* Select the number of '''LUS cards''' installed.
* Switch to the '''Timing''' tab.
* Set '''Answer-back timeout''' to 2 seconds. (This is the time that the M100 waits for someone to answer back on a group call/voice page. During this time it is not possible to do new group calls.
[[File:M100Int 47.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Click '''OK'''

==Updating the exchange==
In the menu, click '''Exchange''' and select '''Send data to the exchange'''
[[File:M100Int_14.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Select '''Module 0'''
* Enable '''Number list''' and '''System parameters'''
* Click '''Send'''

==Adding new module to existing M100 exchange==
When there is an existing M100 exchange with modules that are already defined, a new module has to be added before connecting to the Audio Link Interface. In the '''Update system information''' window in SysMain, activate a new module by increasing the number of existing modules by one:
[[File:M100Int_15.PNG|thumb|left|500px]]
<br style="clear:both;" />

The opto cable connects	to the first available output. If no outputs are available, an ACIA card (LBB 7103/56) has to be installed. The ACIA card requires that the exchange is already	fitted with the Computer Card
(LBB 7103/05).

See M100 documentation for further details.

=Programming in AlphaPro (AlphaCom)=
The programming procedures described in this section is for setting up a single-module M100 exchange with an AlphaCom XE7. The setup procedures for equipment other than the above will differ somewhat from that described in this section.

==Installation==
Install and start AlphaPro on your PC.
[[File:M100Int 16.PNG|thumb|left]]
<br style="clear:both;" />

==Creating Nodes==
<u>'''Create a network and an AlphaCom node:'''</u>
* From the menu bar, select '''[+]''' next to the '''Select Network''' drop-down menu. 
[[File:M100Int 18.PNG|left|500px|thumb]]
<br style="clear:both;" />
* Enter '''2''' in the '''Node Number''' field
** This node number must be higher than the M100 node number
* Select '''AlphaCom XE from the '''Node Type''' drop-down menu 
Enter other relevant data for the network.

[[File:M100Int_17.PNG|thumb|left|500px]]
<br style="clear:both;" />

<u>'''Create an M100 node:'''</u> 
* From the menu bar, select '''[+]''' next to the '''Select Exchange''' drop-down menu
[[File:M100Int_19.PNG|left|500px|thumb]]
<br style="clear:both;" />
* Enter '''1''' in the '''Node Number''' field
** This node number must be lower than the AlphaCom node number
* Select '''M100 Node''' from the '''Node Type''' drop-down menu
Enter other relevant data for the node.

[[File:M100Int_20.PNG|thumb|left|500px]]
<br style="clear:both;" />

==Define Data Communication==
* Select the AlphaCom node created previously  
* Click the '''Exchange & System''' icon 
[[File:AP icon Exch.png|left|thumb]]
<br style="clear:both;" />
* Click '''Net Routing'''
* Click '''Insert'''
* Highlight '''M100''' as the destination node and click '''Select'''
[[File:M100Int 22.PNG|left|500px|thumb]]
<br style="clear:both;" />
* Under '''Primary Route''', select '''M100 Link''' from the '''ACDP Link''' drop-down list
* Click '''Close'''' to close the Net Routing window
[[File:M100Int 23.PNG|thumb|left|500px]]
<br style="clear:both;" />

==Define Audio Connections==
* Click the '''Exchange & System''' icon 
[[File:AP icon Exch.png|left|thumb]]
<br style="clear:both;" />
* Click '''Net Audio'''
* Click '''Insert'''
* Highlight '''M100''' as the destination node and click '''Select'''
* Enter '''31''' in the '''Physical no.''' field
* Enter '''1''' in the '''Channel''' field
[[File:M100Int 24.PNG|thumb|left|500px]]
<br style="clear:both;" />
* Click '''Close''' to close the Net Audio window

Repeat this procedure for the number of audio channels desired according to the table below.

[[File:M100Int_25.PNG|thumb|left|500px]]
<br style="clear:both;" />

==Define Global Numbers==
All the M100 numbers needs to be defined in the AlphaCom XE Audio Server.
* Click the '''Directory & Features''' icon 
[[File:AP icon Dir.png|left|thumb]]
<br style="clear:both;" />
* Click '''Insert''''
* Select '''Global Number for AlphaNet – 83''' from the '''Feature''' drop-down list
* Enter '''1''' in the '''Node''' field
* In the '''Directory Number''' field, enter the M100 directory number
* In the '''Display Text''' field, enter an appropriate	station name (special characters, such as &, must be avoided)
* Confirm by clicking '''OK'''

Repeat this procedure for all the M100 directory numbers.

[[File:M100Int 27.PNG|left|thumb|500px]]
<br style="clear:both;" />

==Define a Group==
<u>'''Local Group'''</u>
* Click the '''Groups''' icon and select '''Local Groups'''
[[File:AP icon Grp.png|left|thumb]]
<br style="clear:both;" />
* Select '''Station Group 2''' from the list on the left and click '''Change'''
* Click the '''Members''' tab
* Scroll down in the '''Not Members''' list on the left and select '''Station 31'''
* Click the right-arrow to move it to the '''Members''' list on the right
* Click '''OK''' and close the window

[[File:M100Int 29.PNG|thumb|left|500px]]
<br style="clear:both;" />
'''Note:'''
 To prevent AGA positions from being connected during an All Call, delete these positions as members of Local Group Number 1.

<u>'''Global Group'''</u>

* Click the '''Groups''' icon and select '''Global Groups'''

[[File:AP icon Grp.png|thumb|left|500px]]
<br style="clear:both;" />
* Select '''Global Group 2''' from the list on the left and click '''Change'''
* Click the ''''Members''' tab
* Under '''Not Members''' on the left, select node number '''2''' in the '''Node''' drop-down list
* Select '''Global Group 2''' in the '''Group''' list on the left
* Click the right-arrow to move it to the '''Members''' list on the right
* Click '''OK''' and close the window

[[File:M100Int 30.PNG|500px|thumb|left]]
<br style="clear:both;" />

==Updating the Exchange==
Set your PC’s IP address to '''169.254.1.2'''. Connect a network cable from the computer to the '''Eth0''' port on the exchange.
* In AlphaPro, click the '''SendAll''' button.
* When prompted enter the default username and password:
** Username: '''admin'''
** Password: '''alphaadmin'''
* When prompted change the node number from default 1 to '''2'''.
* When upload is completed, click close.

=Programming in AlphaWeb=
The programming is done in the web-based tool, AlphaWeb.
* Open a web browser and enter the IP address of the AlphaCom.
** Default IP address: 169.254.1.5
* Log in using the same default username and password as for the AlphaPro.
* Click the '''System Configuration''' tab and then click '''Licensing''' from the left menu.
* Click '''Insert new License Key''' and enter a valid license key required to run the M100 interface software in AlphaCom and click '''Insert Key'''
* Click the '''External Systems''' tab and click '''M100''' from the left menu.

==General Settings==
* Under '''General''' settings, enter '''2''' in the '''AMC Node''' field and set '''M100 Node''' to '''1'''.
* Click '''Save'''
[[File:M100Int 31.PNG|thumb|left|500px]]
<br style="clear:both;" />

==Group Call Map==
* Click '''Group Call Map''' from the left menu
* From the drop-down list, '''F71 All Call''' to '''1 - 9001'''
* Click '''Save'''
[[File:M100Int 32.PNG|thumb|left|500px]]
<br style="clear:both;" />

==Module/Serial Port==
* Click '''Module/Serial Port''' from the left menu
* Under '''Input Table''', for '''M100 Module''' number '''1''' select '''Serial0''' from the '''AlphaCom Serial Port''' drop-down list
* Click '''Save'''
[[File:M100Int 33.PNG|thumb|left|500px]]
<br style="clear:both;" />

==AGA-LUS Map==
To enter settings for 8 or 16 audio channels, click '''AGA-LUS Map'''.
===8 Audio Channels===
* Set '''Number of M100 LUS''' to '''8'''
* Set '''Group Call AGA''' to '''1'''
* Under '''Input Table''' enter the data according to the image below
* Click '''Save'''
[[File:M100Int 34.PNG|thumb|left|500px]]
<br style="clear:both;" />

===16 Audio channels===
* Set '''Number of M100 LUS''' to '''16'''
* Set '''Group Call AGA''' to '''1'''
* Under '''Input Table''' enter the data according to the image below
* Click '''Save'''
[[File:M100Int 35.PNG|thumb|left|500px]]
<br style="clear:both;" />

==Small Reset==
To carry out a small reset:
* Click the '''System Maintenance''' tab
* Select '''System Recovery''' in the left menu
* Click '''Small Reset'''
* Confirm by clicking '''Yes'''
[[File:M100Int 36.PNG|thumb|left|500px]]
<br style="clear:both;" />

{{Note|Whenever a change to the AlphaWeb settings are done and '''Save''' is clicked, the software writes the changes to an XML file in the audio server/exchange. To make the audio server/exchange read the new XML  file, a  Small Reset  has to be carried out.}}

{{Warn|'''<u>Any</u>''' changes in the AlphaCom directory numbers list '''<u>requires</u>''' a '''Save''' under '''External Systems -> General''' followed by a '''Small Reset''' in AlphaWeb.}}

=Door Opening=
This application describes how to perform door opening from Alphacom to M100, and is based on the AlphaCom Ringing Group Feature. <br/>
The M100 Door Station dials a number (in this example 6701), then direct this call to a Ringing Group in the AlphaCom. The Ringing Group contains one (or more) stations that should receive door calls.

==AlphaPro==
===Ringing Group Members===
In Groups -> Local Groups scroll down to '''group 51 - Ringing Group 1'''. Choose which AlphaCom stations that should receive door calls as members:

[[File:M100Int 42.PNG|thumb|left|500px]]
<br style="clear:both;" />

===Door opening Feature===
In '''Directory&Features''', find entry '''6 - Open Door''':

[[File:M100Int 37.PNG|thumb|left|500px]]
<br style="clear:both;" />

Change entry '''6 - Open Door''' from feature '''58 - Remote Control''' to feature '''108 - Event During Conversation''' with ID 0:

[[File:M100Int 38.PNG|thumb|left|500px]]
<br style="clear:both;" />

===Door Opening Event===
In '''Exchange&System''', click '''Events''' and then '''Insert''':

[[File:M100Int 39.PNG|thumb|left|500px]]
<br style="clear:both;" />

If there are more stations that should be able to do '''Door Opening''', then these should be in a [[UDP]] group:

[[File:M100Int 43.PNG|thumb|left|500px]]
<br style="clear:both;" />

Then the owner in previous event must be changed:

[[File:M100Int 44.PNG|thumb|left|500px]]
<br style="clear:both;" />

===Class of Service===
For all stations that should execute '''Door Opening''' or '''Event During Conversation''' feature, make sure that the '''108 - Event During Conversation''' feature is included in the stations [[COS]]:

[[File:M100Int 40.PNG|thumb|left|500px]]
<br style="clear:both;" />

==AlphaWeb==
* Navigate to '''External Systems''' -> '''M100''' -> '''Ringing Group''':

[[File:M100Int 41.PNG|thumb|left|500px]]
<br style="clear:both;" />

* Enter the '''M100 Number to Activate Ringing Group''' (same number as dialed when the M100 Door station presses the door key (typically key 6). 
 This is also configured in the M100 SysMain '''Short Call''' list for the specified Door station and key (use direct or indirect).
* Select the configured '''Ringing Group''' that should receive the '''Door Calls'''.

==SysMain==
* Navigate to '''Tables''' -> '''Number List'''.
* Click '''Insert'''.
* Set a shown below and click '''OK'''.

[[File:M100Int 48.PNG|thumb|left|500px]]
<br style="clear:both;" />

=Secretary/Transfer=
This application describes how to create the possibility to use the '''Secretary''' functionality from M100 stations to AlphaCom stations. <br/>
<br/>

==Programming==
AlphaCom stations that are supposed to be transferred to, must be added as numbers in the virtual module in M100. Go to '''Tables -> Number List''' and press '''Insert''':

[[File:M100Int 45.PNG|thumb|left|500px]]
<br style="clear:both;" />

* ''Module No'': This is the module number in the M100 that the AlphaCom is connected as.
* ''Real No'': This is the physical connection in an M100 module. Since this is a virtual module it doesn’t matter which is number is used.
* ''Call No'': The directory number of the station in AlphaCom that the transfer should go to.
* Leave the rest to default and press OK. Close the Number list Table.


To set up the Executive/Secretary relationship, go to '''Tables -> Transfer list with Group hunt''' and press '''Insert''':

[[File:M100Int 46.PNG|thumb|left|500px]]
<br style="clear:both;" />

* ''Primary Call No'': The M100 station that can initiate transfer by using the F1/F0 codes.
* ''Secondary Call No'': The AlphaCom station that receives the calls to 500 when 500 has used F1.
* ''Control'': The mechanism used for this transfer.  
Press OK and close the Transfer list with Group hunt table.

Go to '''Exchange -> Send data to the exchange''' and select module 00 (The M100 module). Select '''Number list (all)''' and '''Transfer''' to be sent.

==Operation==
* M100 Station 500 receives the calls as normal.
* The person at M100 station 500 leaves and wants to forward his calls to an operator at AlphaCom station 110.
* M100 user presses F1.
* Any M100 station calling 500 will be rerouted to 110.
* The transfer is turned off by pressing F0 at M100 station 500.

=AlphaNet=
When there are more AlphaComs in the system that should communicate with M100 stations some extra care must be taken.

All other AlphaComs must have the correct routing. The AlphaCom that is physically connected to the M100 system will act as a transit node. In the example image below '''AXE7''' is the interface node. '''AXE7_2''' is the second AlphaCom:

[[File:M100Int 49.PNG|thumb|left|500px]]
<br style="clear:both;" />

[[Category:3rd party integration]]