View source for SDS-1

{{AEIPS}}
[[Image:SDS-1.png|thumb|500px|IP Phone SDS-1 (1490000010)]]

== Getting Started ==
===Installing the Phone with Phone Stand===
# Insert the hooks on top of the stand into the slots on the back of the phone. (You can either use the upper OR the lower slots)
# Firmly slide the stand upward to lock it in place
[[File:SDS setup1.png|thumb|400px|left]]
<br style="clear:both;" />

===Installing the Phone with Wall Mount===
# Insert all 4 hooks located at the front of the wallmount into the slots on the back of the phone.
# Firmly slide the wall mount upward to lock it in place.
# Attach the phone to the wall via the wall mount holes.
[[File:SDS_setup2.png|thumb|left|500px]]
<br style="clear:both;" />
# Pull out the tab from the handset cradle (see figure below).
# Rotate the tab and plug it back into the slot with the extension up to hold the handset while the phone is mounted on the wall.
[[File:SDS_setup3.png|thumb|left|500px]]
<br style="clear:both;" />

==Connecting the phone==
# Connect the handset and main phone case with the phone cord.
# Connect the LAN port of the phone to the RJ-45 socket of a PoE switch using the Ethernet cable. <br/> The LCD will display provisioning or firmware upgrading information. Before continuing, please wait for the date/time display to appear.
# Using the web configuration interface or the keypad configuration menu, you can further configure the phone using either a static IP or DHCP.

[[File:SDS_setup4.png|thumb|left|500px]]
<br style="clear:both;" />

==Configuration==
The IP phone can only operate in SIP mode. 
# Ensure your phone is properly powered up and connected to the Internet.
# Press the Menu key to enter the menu of the phone.
# Navigate to Status > Network Status and press the Menu key to check the IP address.
# Enter the phone’s IP address in your PC’s browser
# Log in by entering the default Username: admin and Password: alphaadmin
[[File:SDS config1.png|thumb|left|500px]]
<br style="clear:both;" />

Register the account on the SDS-1 by selecting '''ACCOUNTS > Account 1/2 > General Settings''' to configure '''Account Name''', '''SIP Server''' (ICX-AlphaCom or IC-EdgePulse), '''SIP User ID''' (Extension Number).
[[File:SDS config2.png|thumb|left|500px]]
<br style="clear:both;" />

===Register to ICX-AlphaCom server===
====Account setup====
* Select ACCOUNTS > Account 1 > General Settings
[[File:SDS config3.png|thumb|left|500px]]
<br style="clear:both;" />

Enter the values shown above for the parameters
* Account Active: Check Yes button
* SIP Server: IP address of ICX-AlphaCom server
* SIP User ID: Directory Number of SDS-1 phone
* Authenticate ID: Same as SIP User ID

{{note|For changes to take effect, it may be necessary to temporarily disable the account. First check the '''No''' button for '''Account Active''', then click '''Save and Apply'''. Once this is done, re-enable the account by checking the '''Yes''' button for '''Account Active''' followed by '''Save and Apply''' again.}}

====Audio Settings====
* Check in AlphaPro under Users & Stations the codec that has been selected for the SIP phone (normally G722)
* Select Account 1 > Audio Settings
[[File:SDS config4.png|thumb|left|500px]]
<br style="clear:both;" />

Set all codecs from the Preferred Vocoder list to the one defined in AlphaPro, i.e. G722.

===Register to IC-Edge Controller===
====Account setup====
Select ACCOUNTS > Account 1 > General Settings
[[File:SDS config5.png|thumb|left|500px]]
<br style="clear:both;" />

Enter the values shown above for the parameters
* Account Active: Check Yes button
* SIP Server: IP address of intercom station set as Edge Controller
* SIP User ID: Directory Number of the SDS-1 phone
* Authenticate ID: Same as SIP User ID

====Edge Group Call====
<div style="text-align:left;"> <youtube width="300" height="180">vaiUmx7kRiI</youtube>  </div>
<br><br>
The Edge Controller transmits group calls using IP multicast paging. Each group call uses its own unique multicast IP address. To find the multicast IP address:
* Log into the Edge Controller
* Select Edge Controller > Group Call
[[File:Edge GroupCall.PNG|thumb|left|500px]]
<br style="clear:both;" />

Make a note of the multicast addresses under '''Group Audio Address'''.
* Log into the SDS-1
* Select Setting > Multicast Paging
[[File:SDS config7.png|thumb|left|500px]]
<br style="clear:both;" />
* Set Multicast Paging Codec to G722
* Enter the multicast addresses under Listening Address
* Click Save and Apply
When a Group Call is activated, the SDS-1 will automatically broadcast the audio in the loudspeaker. The SDS-1 will display the text of the Group Call as entered under '''Nickname'''. If the SDS-1 is busy in a regular call when a Group Call is made, it will by default not play the Group Call audio. If '''Paging Barge''' is set to value '''2''' or higher, the current call will be placed On Hold, and the Group Call audio will be broadcast. When the Group Call is ended, press the Hold button to resume the regular call.

===Tips for using SDS-1===
Do not Disturb mode: Toggling "Do not disturb" mode is done by pressing the mute button on the keypad. Status is shown in the display.

[[File:SDS1dnd.png|thumb|left|500px]]
<br style="clear:both;" />

The mute key function can be changed in the web interface, under Settings and Call Features.

[[File:SDS1_mute_web.png|thumb|left|500px]]
<br style="clear:both;" />

== Dimensions ==
* Phone dimensions
[[File:SDS Dimensions1.png|300px|thumb|left|Front view]]
[[File:SDS Dimensions2.png|100px|thumb|left|Left view]]
[[File:SDS Dimensions3.png|300px|thumb|left|Rear view]]
<br style="clear:both;" />

* Bracket dimensions
[[File:SDS Dimensions4.png|300px|thumb|left|Wall mount bracket]]
[[File:SDS Dimensions5.png|300px|thumb|left|Wall mount bracket - side view]]
<br style="clear:both;" />

== Related information ==
* [https://www.zenitel.com/product/sds-1 Additional Documentation on Zenitel.com]

[[Category: Other IP based devices]]