View source for Turbine Compact Board Connectors

{{AEIPS}}
==Main PCB (A100C08121) ==
===Front===
[[File:TCIS Connections 3.PNG|500px]]

<br style="clear:both;" />

'''P1''' RJ45 PoE port for 10/100 Mbit Ethernet connection.
:The station can be powered from this port if the line supports Power over Ethernet (PoE).
[[File:TCIS Connections 4.PNG|thumb|500px|left]]
<br style="clear:both;" />

'''P2''' 5-pin plug-on terminal for relay and external power
[[File:TCIS Connections 5.PNG|thumb|500px|left]]
<br style="clear:both;" />
:Pin 1/2:  24 VDC for external secondary power if PoE is not used. Pin 1 is positive.
:Pin 3: COM relay (Common)
:Pin 4: NO relay (Normally Open)
:Pin 5: NC relay (Normally Closed)

* Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
* Connectable conductors:  0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².

'''P3'''  10-pin plug-on terminal for I/O's and Audio Line Out
[[File:TCIS Connections 6.PNG|thumb|300px|left]]

:Pin 1  5.3V (max. 200mA current)
:Pin 2  GND
:Pin 3  Button Input or LED Driver
:Pin 4  Button Input or LED Driver
:Pin 5  Button Input or LED Driver
:Pin 6  Button Input or LED Driver
:Pin 7  Button Input or LED Driver
:Pin 8  Button Input or LED Driver
:Pin 9  600 ohm balanced line out +
:Pin 10  600 ohm balanced line out -

<br style="clear:both;" />
* Connectable conductors:  0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².

'''P4'''  Loudspeaker & Electret microphone
[[File:TCIS Connections 7.PNG|thumb|500px|left]]
<br style="clear:both;" />
:Pin 1: Speaker output +
:Pin 2: Speaker output -
:Pin 3:  Electret Microphone +
:Pin 4:  Electret Microphone -

* Connectable conductors:  0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
* Recommended loudspeaker impedance: 8 ohms

 {{Note | To enable the electret microphone input when using a [[TKIS-2]], the "'''Product Model And Accessory'''" must be set to "'''Kit'''" under [[Main Settings (IP Stations)|Station Main > Main Settings]] in the web interface of the device.}}



===Output Connectors + 1 relay===
[[File:TCIS Connections 12.PNG|500px|Connecting to the onboard relay. Extra LED controlled by output 1]]

The extra relay for any of the 6 I/O pins is connected as shown:

[[File:TurbineCompactOutputs.PNG|400px]]

Most general purpose P-Channel MOSFET's should work. Recommended example: BSS84

The 5,3V output can deliver 200mA current maximum

See also [[Adding additional relay(s) to a Zenitel IP Device]]

===Rear===
[[File:TCIS Connections 8.PNG|500px]]


'''J6'''  10-pin terminal for digital MEMS Microphone
[[File:TCIS Connections 9.PNG|thumb|500px|left]]
:Pin 1  Left mic select (Vdd)
:Pin 2  Right mic select (GND)
:Pin 3  Data
:Pin 4  Data
:Pin 5  Vdd 3.3V
:Pin 6  Vdd 3.3V
:Pin 7  CLK
:Pin 8  CLK
:Pin 9  GND
:Pin 10  GND

<br style="clear:both;" />

==Front Board (A100C08129)==
 {{Note | Not applicable to TKIS-2 and TMIS-x}}
===Front===
[[File:TCIS Connections 10.PNG|500px]]

<br style="clear:both;" />

===Rear===
[[File:TCIS Connections 11.PNG|500px]]

<br style="clear:both;" />

[[Category: Turbine Connections]]