Difference between revisions of "VOIP AUDIO CONFIG"
From Zenitel Wiki
| Line 8: | Line 8: | ||
|colspan="3"|'''$VAC L101 U1 '10.5.11.32' W1234 W4322 '''|| colspan="2"|Configure the IP audio parameters for station 101, G711 to 10.5.11.32 port 1234, incoming audio to AlphaCom on port 4322. | |colspan="3"|'''$VAC L101 U1 '10.5.11.32' W1234 W4322 '''|| colspan="2"|Configure the IP audio parameters for station 101, G711 to 10.5.11.32 port 1234, incoming audio to AlphaCom on port 4322. | ||
|- | |- | ||
| − | |colspan="5"|$VAC configure the RTP audio stream for "RTP-stream station", to activate the audio the station must be called or controlled by $CONN etc. | + | |colspan="5"|$VAC configure the RTP audio stream for "RTP-stream station", to activate the audio the station must be called or controlled by $CONN etc. <br> Note that RTP uses even port numbers, and RTCP uses odd port numbers. So it must be at least 2 between source and destination port. E.g. 2000, 2002 etc. |
| + | |||
|- | |- | ||
|align=center|1||[[NET_OBJ_REF]]||colspan="3"| Source AlphaCom station | |align=center|1||[[NET_OBJ_REF]]||colspan="3"| Source AlphaCom station | ||
Revision as of 16:50, 19 May 2014
| VAC (VOIP_AUDIO_CONFIG) | 0x00AF | 175 | AMC 11.02 | |
|---|---|---|---|---|
| $VAC L101 U1 '10.5.11.32' W1234 W4322 | Configure the IP audio parameters for station 101, G711 to 10.5.11.32 port 1234, incoming audio to AlphaCom on port 4322. | |||
| $VAC configure the RTP audio stream for "RTP-stream station", to activate the audio the station must be called or controlled by $CONN etc. Note that RTP uses even port numbers, and RTCP uses odd port numbers. So it must be at least 2 between source and destination port. E.g. 2000, 2002 etc. | ||||
| 1 | NET_OBJ_REF | Source AlphaCom station | ||
| 2 | UINT1 | Codec type<br\> AlphaCom level codecs <br\> 1. G711U <br\> 2. G711a <br\> 3. G722 <br\><br\> Telecom level codecs (+9dB louder than AlphaCom level) 6. G711U 7. G711A 8. G722 | ||
| 3 | TEXT16 | Destination IP address | ||
| 4 | UINT2 | Destination IP port | ||
| 5 | UINT2<br\>(optional) | Port in AlphaCom for receiving audio from external source. (If port not specified streaming to AlphaCom is not possible) | ||
| 6 | UINT1<br\>(optional) | MultiCast Ethernet port 0 or 1. If the AlphaCom system is set up for MultiCast this parameter specify the physical eth where the MulitCast rtp group and program conference should be transmitted. Default is unicast (value 2). | ||
&000204 .ex_profile.flags.RTP_stream_man_reg = 0 (0x00000000)
By default the RTP stream station is "REGISTERED" during system start up. If manual registration is needed the system flag "RTP_stream_man_reg" can be used. If set the RTP stream station is down until the first "$VAC" command is received.
Group Call and Program Conference
When the RTP-stream station is included in a group call or program conference the RTP stream is sent to the destination IP address as specified in param 3 of $VAC. The IP port used is the port specified for IP station Group Call and Program Conference.
ex_profile.ip_config.ip_st_audio_group = 61002 (0xee4a) ex_profile.ip_config.ip_st_audio_prog = 61004 (0xee4c)