Difference between revisions of "IPHA - Monitoring server status"
From Zenitel Wiki
(→Configuration) |
|||
| Line 24: | Line 24: | ||
Copy/paste the action commands below into the event: | Copy/paste the action commands below into the event: | ||
| + | {{Code2| | ||
tmp 2 "2" | tmp 2 "2" | ||
| − | IF %op(%sev,,230) | + | IF %op(%sev,<nowiki>==</nowiki>,230) |
tmp 2 "1" | tmp 2 "1" | ||
ENDIF | ENDIF | ||
| − | IF %op(%sev,==,231) | + | IF %op(%sev,<nowiki>==</nowiki>,231) |
tmp 2 "1" | tmp 2 "1" | ||
ENDIF | ENDIF | ||
| − | IF %op(%sev,==,232) | + | IF %op(%sev,<nowiki>==</nowiki>,232) |
tmp 2 "1" | tmp 2 "1" | ||
ENDIF | ENDIF | ||
| − | IF %op(%tmp(2),==,1) | + | IF %op(%tmp(2),<nowiki>==</nowiki>,1) |
tmp 0 "Primary Server is operational." | tmp 0 "Primary Server is operational." | ||
IF %op(%syse(232) ,&, %syse(230)) | IF %op(%syse(232) ,&, %syse(230)) | ||
tmp 0 "Secondary Server is operational." | tmp 0 "Secondary Server is operational." | ||
ENDIF | ENDIF | ||
| − | IF %op(%op(%syse(230),==,0) ,&, %op(%syse(232),==,0)) | + | IF %op(%op(%syse(230),<nowiki>==</nowiki>,0) ,&, %op(%syse(232),<nowiki>==</nowiki>,0)) |
tmp 0 "Secondary Server is operational." | tmp 0 "Secondary Server is operational." | ||
ENDIF | ENDIF | ||
| Line 45: | Line 46: | ||
tmp 1 "Both servers are running." | tmp 1 "Both servers are running." | ||
ENDIF | ENDIF | ||
| − | IF %op(%syse(231),==,0) | + | IF %op(%syse(231),<nowiki>==</nowiki>,0) |
tmp 1 "ALARM: The link to the other server is down, or the server itself is down" | tmp 1 "ALARM: The link to the other server is down, or the server itself is down" | ||
ENDIF | ENDIF | ||
| − | LOG "%tmp(0) %tmp(1)" | + | LOG "%tmp(0) %tmp(1)"}} |
[[Category: AlphaCom Monitoring]] | [[Category: AlphaCom Monitoring]] | ||
Revision as of 12:27, 31 May 2022
The IP-HA system reports changes of the server state to the Event Handler.
This article describes how to configure the Event Handler in order to report current server state to the System log.
Error reporting
The following strings will be reported to the System Log whenever there is a change of state:
- One of the servers is operational, and the other server is in standby mode:
Primary Server is operational. Both servers are running.
|
Secondary Server is operational. Both servers are running.
|
- One of the servers is operational, and the other server is Out of Service:
Primary Server is operational. ALARM: The link to the other server is down, or the server itself is down.
|
Secondary Server is operational. ALARM: The link to the other server is down, or the server itself is down.
|
Configuration
From AlphaPro, select Exchange & System > Events, and Insert a new event with the following properties:
Copy/paste the action commands below into the event:
Action commands:
tmp 2 "2" IF %op(%sev,==,230) tmp 2 "1" ENDIF IF %op(%sev,==,231) tmp 2 "1" ENDIF IF %op(%sev,==,232) tmp 2 "1" ENDIF IF %op(%tmp(2),==,1) tmp 0 "Primary Server is operational." IF %op(%syse(232) ,&, %syse(230)) tmp 0 "Secondary Server is operational." ENDIF IF %op(%op(%syse(230),==,0) ,&, %op(%syse(232),==,0)) tmp 0 "Secondary Server is operational." ENDIF IF %syse(231) tmp 1 "Both servers are running." ENDIF IF %op(%syse(231),==,0) tmp 1 "ALARM: The link to the other server is down, or the server itself is down" ENDIF LOG "%tmp(0) %tmp(1)"