Difference between revisions of "IPHA - Monitoring server status"
From Zenitel Wiki
| (15 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{AI}} |
| − | The [[ | + | The [[Redundant Servers - ICX-AlphaCom|IP-HA system]] reports changes of the server state to the [[Event Handler]]. |
This article describes how to configure the Event Handler in order to report current server state to the [[System log]]. | This article describes how to configure the Event Handler in order to report current server state to the [[System log]]. | ||
== Error reporting == | == Error reporting == | ||
| − | + | At the change of state is either: | |
| + | * Communication between the servers is lost or resumed | ||
| + | * A server changes state from Standby to Operational, or vice versa | ||
| + | |||
| + | the following strings will be reported to the System Log whenever there is a change of state. | ||
* One of the servers is operational, and the other server is in standby mode: | * One of the servers is operational, and the other server is in standby mode: | ||
| Line 18: | Line 22: | ||
From AlphaPro, select '''Exchange & System''' > '''Events''', and '''Insert''' a new event with the following properties: | From AlphaPro, select '''Exchange & System''' > '''Events''', and '''Insert''' a new event with the following properties: | ||
| − | [[File:IPHA | + | [[File:IPHA Event Mon1.PNG|left|thumb|500px|Event to collect the status in the IPHA system]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| Line 24: | Line 28: | ||
{{Code2| | {{Code2| | ||
| − | IF %op(%sev,>=,230) | + | IF %op(%sev,><nowiki>=</nowiki>,230) |
| − | IF %op(%sev,<=,232) | + | IF %op(%sev,<<nowiki>=</nowiki>,232) |
!Primary Server is operational | !Primary Server is operational | ||
WUDD 1001 1 | WUDD 1001 1 | ||
| Line 32: | Line 36: | ||
WUDD 1001 2 | WUDD 1001 2 | ||
ENDIF | ENDIF | ||
| − | IF %op(%op(%syse(230),==,0) ,&, %op(%syse(232),==,0)) | + | IF %op(%op(%syse(230),<nowiki>==</nowiki>,0) ,&, %op(%syse(232),<nowiki>==</nowiki>,0)) |
!Secondary Server is operational | !Secondary Server is operational | ||
WUDD 1001 2 | WUDD 1001 2 | ||
| Line 40: | Line 44: | ||
WUDD 1002 1 | WUDD 1002 1 | ||
ENDIF | ENDIF | ||
| − | IF %op(%syse(231),==,0) | + | IF %op(%syse(231),<nowiki>==</nowiki>,0) |
!No communication with the other server | !No communication with the other server | ||
WUDD 1002 0 | WUDD 1002 0 | ||
| Line 47: | Line 51: | ||
$ST L%1.dir W100 L9999 | $ST L%1.dir W100 L9999 | ||
ENDIF | ENDIF | ||
| − | ENDIF}} | + | ENDIF |
| + | }} | ||
| + | |||
| + | |||
| + | From AlphaPro, select '''Exchange & System''' > '''Events''', and '''Insert''' a second event with the following properties (note that the ID of the event Owner must be "1"): | ||
| + | |||
| + | [[File:IPHA Event Mon2.PNG|left|thumb|500px|Event to report the status to the System Log]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | Copy/paste the action commands below into the event: | ||
| + | |||
| + | {{Code2| | ||
| + | IF %op(%udd(1001),<nowiki>=</nowiki>,1) | ||
| + | tmp 1 "Primary Server is operational." | ||
| + | ENDIF | ||
| + | IF %op(%udd(1001),<nowiki>=</nowiki>,2) | ||
| + | tmp 1 "Secondary Server is operational." | ||
| + | ENDIF | ||
| + | IF %op(%udd(1002),<nowiki>=</nowiki>,1) | ||
| + | tmp 2 "Both servers are running." | ||
| + | ENDIF | ||
| + | IF %op(%udd(1002),<nowiki>=</nowiki>,0) | ||
| + | tmp 2 "WARNING: No communication with the other server." | ||
| + | ENDIF | ||
| + | LOG "%tmp(1) %tmp(2)" | ||
| + | }} | ||
| + | |||
[[Category: AlphaCom Monitoring]] | [[Category: AlphaCom Monitoring]] | ||
| + | [[Category: Redundancy]] | ||
Latest revision as of 15:44, 28 June 2022
The IP-HA system reports changes of the server state to the Event Handler.
This article describes how to configure the Event Handler in order to report current server state to the System log.
Error reporting
At the change of state is either:
- Communication between the servers is lost or resumed
- A server changes state from Standby to Operational, or vice versa
the following strings will be reported to the System Log whenever there is a change of state.
- One of the servers is operational, and the other server is in standby mode:
Primary Server is operational. Both servers are running.
|
Secondary Server is operational. Both servers are running.
|
- One of the servers is operational, and the other server is Out of Service:
Primary Server is operational. WARNING: No communication with the other server.
|
Secondary Server is operational. WARNING: No communication with the other server.
|
Configuration
From AlphaPro, select Exchange & System > Events, and Insert a new event with the following properties:
Copy/paste the action commands below into the event:
Action commands:
IF %op(%sev,>=,230) IF %op(%sev,<=,232) !Primary Server is operational WUDD 1001 1 IF %op(%syse(232) ,&, %syse(230)) !Secondary Server is operational WUDD 1001 2 ENDIF IF %op(%op(%syse(230),==,0) ,&, %op(%syse(232),==,0)) !Secondary Server is operational WUDD 1001 2 ENDIF IF %syse(231) !Both servers are running WUDD 1002 1 ENDIF IF %op(%syse(231),==,0) !No communication with the other server WUDD 1002 0 ENDIF !Start a 10 sec timer $ST L%1.dir W100 L9999 ENDIF ENDIF
From AlphaPro, select Exchange & System > Events, and Insert a second event with the following properties (note that the ID of the event Owner must be "1"):
Copy/paste the action commands below into the event:
Action commands:
IF %op(%udd(1001),=,1) tmp 1 "Primary Server is operational." ENDIF IF %op(%udd(1001),=,2) tmp 1 "Secondary Server is operational." ENDIF IF %op(%udd(1002),=,1) tmp 2 "Both servers are running." ENDIF IF %op(%udd(1002),=,0) tmp 2 "WARNING: No communication with the other server." ENDIF LOG "%tmp(1) %tmp(2)"