Actions

Difference between revisions of "1-3c. IP Stations – SoftClient (solution)"

From Zenitel Wiki

(→‎Install and configure the SoftClient)
(→‎Related articles)
 
(12 intermediate revisions by 2 users not shown)
Line 4: Line 4:
  
 
=== Install and configure the SoftClient ===
 
=== Install and configure the SoftClient ===
−
* Download the file '''SoftClientSetup.msi''' from e.g. AlphaWiki or from Partnernet,  and install it on the PC
+
* Download the file '''SoftClientSetup.msi''' from e.g. [[Downloads|Wiki download page]] or from Partnernet,  and install it on the PC
−
* Assign to the PC the IP address 10.1.10.2, and subnet mask 255.255.0.0
+
* If not already done, change the IP address of the PC to 10.1.10.90, and subnet mask 255.255.0.0
−
* Start the SoftClient, and select File -> Preferences, and set these parameters:
+
* Start the SoftClient, and select '''File''' -> '''Preferences''', and set these parameters:
−
[[File:1-3c solution1.png|thumb|left|250px|Off-line menu: IP settings]]
+
[[File:1-3c solution1.PNG|thumb|left|250px|SoftClient: File -> Preferences window]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
−
* When prompted, '''Save''' the changes. When asked for "Restart now" you can select "No".
+
* '''Save Settings'''
−
* Step to the menu selection '''AlphaCom IP''' and enter the following parameters:
+
* Select '''Configure Audio Device''' to adjust speaker and microphone levels
−
[[File:1-3a solution2.png|thumb|left|250px|Off-line menu: AlphaCom settings]]
 
−
<br style="clear:both;" />
 
−
* When prompted, '''Save''' the changes.
 
−
* Step to the menu selection '''Restart''' and activate a restart of the station
 
  
 
===Configure the AlphaCom XE===
 
===Configure the AlphaCom XE===
 
*In AlphaPro go to '''Users & Stations''', and select physical number 40; 140 Station 40
 
*In AlphaPro go to '''Users & Stations''', and select physical number 40; 140 Station 40
 
*Use the section on the right and change the configuration as follows:
 
*Use the section on the right and change the configuration as follows:
−
[[File:1-3c solution5.png|thumb|left|400px|AlphaPro: Users & Stations window]]
+
[[File:1-3c solution2.PNG|thumb|left|400px|AlphaPro: Users & Stations window]]
−
<br style="clear:both;" />
 
−
 
 
−
*In AlphaPro go to '''Users & Stations''', and select physical number 38; 138 Station 38
 
−
*Use the section on the right and change the configuration as follows:
 
−
 
 
−
[[File:1-3a solution6.png|thumb|left|400px|AlphaPro: Users & Stations window]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
Line 41: Line 31:
 
===Related articles ===
 
===Related articles ===
 
* [[1-3c. IP Stations – SoftClient (practice)]]
 
* [[1-3c. IP Stations – SoftClient (practice)]]
 +
 +
[[Category: AlphaCom practice]]

Latest revision as of 09:04, 30 June 2022

System configuration



Install and configure the SoftClient

  • Download the file SoftClientSetup.msi from e.g. Wiki download page or from Partnernet, and install it on the PC
  • If not already done, change the IP address of the PC to 10.1.10.90, and subnet mask 255.255.0.0
  • Start the SoftClient, and select File -> Preferences, and set these parameters:
SoftClient: File -> Preferences window


  • Save Settings
  • Select Configure Audio Device to adjust speaker and microphone levels

Configure the AlphaCom XE

  • In AlphaPro go to Users & Stations, and select physical number 40; 140 Station 40
  • Use the section on the right and change the configuration as follows:
AlphaPro: Users & Stations window


  • Send the changes to the AlphaCom XE

SendChg.PNG

Troubleshooting

  • If the SoftClient does not register, check the following:
    • In AlphaWeb, System Configuration -> Filters, verify that port for IP Stations and VoIP Audio is enabled
    • In AlphaWeb, System Configuration -> Licenses, verify that there are licenses installed for the SoftClient





Related articles

Retrieved from "https://wiki.zenitel.com/w/index.php?title=1-3c._IP_Stations_–_SoftClient_(solution)&oldid=229860"