Difference between revisions of "Cold Start of AMC-IP"
From Zenitel Wiki
(→Cold start procedure) |
(→Modify Factory Default Settings) |
||
| (27 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | {{A}} | |
| − | + | Performing a '''cold start''' of the AMC-IP board will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0. | |
| − | |||
| − | programming, load | ||
| − | to 169.254.1.5 with mask 255.255.0.0 on Eth0 | ||
| − | |||
===Cold start procedure=== | ===Cold start procedure=== | ||
| − | [[Image:Cold Start of AMC-IP.jpg|right| | + | [[Image:Cold Start of AMC-IP.jpg|right|130px|thumb|Cold start to load default factory settings]] |
| − | *Turn the exchange mains switch ON (on the back of the | + | *Turn the exchange mains switch ON (on the back of the cabinet). |
| − | cabinet). | + | *Hold the [[AMC-IP#LED indicators|cold start button]] on the [[AMC-IP]] board depressed. |
| − | *Hold the cold start button on the AMC-IP board depressed. | + | *Press the reset button on the [[APC]] card briefly. (On the E7 exchange, the reset button is located on the power card.) |
| − | *Press the reset button on the APC card briefly. | + | *Keep the cold start button pressed at least 2 sec. after reset. The AMC status LED will blink green when the boot is ready. |
| − | (On the E7 exchange, the reset button is located on the power | ||
| − | card.) | ||
| − | *Keep the cold start button pressed at least | ||
| − | The AMC status LED will blink green when the boot is ready. | ||
| + | <br/><br/> | ||
=== Cold-start of AMC application only, keep IP setting === | === Cold-start of AMC application only, keep IP setting === | ||
| + | [[Image:Cold Start of AMC-IP.2.jpg|right|130px|thumb|Cold-start of AMC application]] | ||
| + | *Press the reset button on the APC card briefly. (On the E7 exchange, the reset button is located on the power card.) | ||
| + | *After 10 sec., press the cold start button on the AMC-IP board. | ||
| + | *Keep cold start button pressed until AMC running LED is blinking green. | ||
| + | ><br/><br/> | ||
| + | |||
| + | == Modify Factory Default Settings == | ||
| + | After cold start the system is set up with a default program and is working without any further programming. To change or add to the default settings, the [[AlphaPro]] programming tool must be used. | ||
| − | + | [[Category:Factory Default]] | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Latest revision as of 12:00, 20 August 2024
Performing a cold start of the AMC-IP board will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0.
Cold start procedure
- Turn the exchange mains switch ON (on the back of the cabinet).
- Hold the cold start button on the AMC-IP board depressed.
- Press the reset button on the APC card briefly. (On the E7 exchange, the reset button is located on the power card.)
- Keep the cold start button pressed at least 2 sec. after reset. The AMC status LED will blink green when the boot is ready.
Cold-start of AMC application only, keep IP setting
- Press the reset button on the APC card briefly. (On the E7 exchange, the reset button is located on the power card.)
- After 10 sec., press the cold start button on the AMC-IP board.
- Keep cold start button pressed until AMC running LED is blinking green.
>
Modify Factory Default Settings
After cold start the system is set up with a default program and is working without any further programming. To change or add to the default settings, the AlphaPro programming tool must be used.