Difference between revisions of "Permanent Audio Stream"
From Zenitel Wiki
| (32 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{AEIPS}} |
| − | The | + | '''Permanent Audio Stream''' (PAS) is a feature in Zenitel Devices enabling transmission of RTP audio streams outside a call. Devices can be configured to permanently transmit up to two RTP streams (configurable). The RTP audio will be sent to a given IP address/port with configured codec. |
| − | + | The configuration page for PAS is not available from the web interface of the device. To access the PAS Settings use the following url: <ipaddress>/goform/'''zForm_stream_config''' | |
| − | + | Optional settings: | |
| + | * Configure the PAS to transmit RTP audio only during a call. | ||
| + | * Configure the PAS to transmit RTP audio only when the call is initiated from a specific DAK key. | ||
| − | |||
| + | The PAS web page: | ||
| + | [[File:PAS2.PNG|thumb|500px|left|Permanent Audio configuration page (Firmware ver. 9)]] | ||
| + | <br style="clear:both;" /> | ||
| − | + | *'''Remote Domain''': The IP address to which the RTP audio will be sent | |
| − | + | *'''Remote Port''': The port number to which the RTP audio will be sent | |
| + | *'''Codec''': Which audio codec to use. Options are: g711a (default), g711u, g722, L16x16D, L16x48D, PCM16, PCM48 | ||
| + | *'''Enable Condition''': | ||
| + | **'''RTP Stream Always Enabled''': Audio stream is permanently transmitted (default) | ||
| + | **'''RTP Stream Enabled During Call''': Audio stream is transmitted only when there is an active call | ||
| + | **'''RTP Stream Started With DAK Key''': Audio stream is transmitted only when the call is initiated from a specific DAK key. | ||
| + | *'''Volume''': Can be adjusted from -20dB to + 20dB | ||
| + | '''Direct Access Key Settings:'''<br> | ||
| + | This setting enables an option to stream audio only when the call is initiated from a specific DAK key. Options are: | ||
| + | * Do Not Record Call | ||
| + | * Record Call Started With This Key | ||
| + | <br> | ||
| + | |||
| + | == The PAS web page in firmware 8 and earlier== | ||
| + | ---- | ||
| + | [[File:PermanentAudio.png|thumb|500px|left|Permanent Audio configuration page]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | Tools like VS-Recorder 2.0 can be used to record the actual RTP audio. | ||
| + | |||
| + | {{Note|In Turbine Video stations the Permanent audio stream is removed on TCIV from sw 4.11, but available on TCIV+}} | ||
| + | |||
| + | [[Category: IC-EDGE Configuration]] | ||
[[Category: Pulse - Configuration]] | [[Category: Pulse - Configuration]] | ||
[[Category: SIP intercom - Configuration]] | [[Category: SIP intercom - Configuration]] | ||
Latest revision as of 13:42, 27 September 2024
Permanent Audio Stream (PAS) is a feature in Zenitel Devices enabling transmission of RTP audio streams outside a call. Devices can be configured to permanently transmit up to two RTP streams (configurable). The RTP audio will be sent to a given IP address/port with configured codec.
The configuration page for PAS is not available from the web interface of the device. To access the PAS Settings use the following url: <ipaddress>/goform/zForm_stream_config
Optional settings:
- Configure the PAS to transmit RTP audio only during a call.
- Configure the PAS to transmit RTP audio only when the call is initiated from a specific DAK key.
The PAS web page:
- Remote Domain: The IP address to which the RTP audio will be sent
- Remote Port: The port number to which the RTP audio will be sent
- Codec: Which audio codec to use. Options are: g711a (default), g711u, g722, L16x16D, L16x48D, PCM16, PCM48
- Enable Condition:
- RTP Stream Always Enabled: Audio stream is permanently transmitted (default)
- RTP Stream Enabled During Call: Audio stream is transmitted only when there is an active call
- RTP Stream Started With DAK Key: Audio stream is transmitted only when the call is initiated from a specific DAK key.
- Volume: Can be adjusted from -20dB to + 20dB
Direct Access Key Settings:
This setting enables an option to stream audio only when the call is initiated from a specific DAK key. Options are:
- Do Not Record Call
- Record Call Started With This Key
The PAS web page in firmware 8 and earlier
Tools like VS-Recorder 2.0 can be used to record the actual RTP audio.
|
In Turbine Video stations the Permanent audio stream is removed on TCIV from sw 4.11, but available on TCIV+ |