Difference between revisions of "IP Heavy Duty Connections"
From Zenitel Wiki
(Created page with "== Introduction == The table below is an overview of the main connectors involved when installing the STENTOFON IP Heavy Duty stations. {|border="1" |width="150px"|LAN |10/10...") |
m (1 revision imported) |
||
(22 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | == | + | {{APS}} [[File:IP HeavyDuty.png|thumb|250px|The IP Heavy Duty Stations]] |
− | + | == Main connectors == | |
+ | To access these connectors the frontplate must be removed. | ||
{|border="1" | {|border="1" | ||
Line 15: | Line 16: | ||
== Power Supply == | == Power Supply == | ||
− | The IP Heavy Duty Station supports Power over Ethernet (PoE, IEEE 802.3 a-f) where power can be drawn from either the spare line or signal line. | + | The [[IP Heavy Duty Station]] supports Power over Ethernet (PoE, IEEE 802.3 a-f) where power can be drawn from either the spare line or signal line. |
− | If PoE is not available, the IP Substation can be connected to a 24 VDC local power supply. | + | If PoE is not available, the IP Substation can be connected to a 24 VDC local power supply. |
− | == | + | == Connections == |
− | There are | + | There are four connectors on the IP heavy Duty station PCB: P1-P4. |
− | + | * '''P1''' RJ45 LAN port is for connecting to the data network | |
− | |||
− | + | * '''P2''': RJ45 AUX port is for connecting to auxiliary equipment such as a PC | |
− | |||
− | + | * '''P3''': 6-pin plug-on screw terminal for external connections. | |
− | + | **Pin 1/2: Connection of external 8 ohm loudspeaker (optional). | |
− | :* | + | **Pin 3/4: Internal NO relay contact for additional call indication, etc. |
− | :* | + | **Pin 5/6: Connect 24VDC power supply if PoE is not used |
− | :* | + | [[File:IP Substation Main Board 1.PNG|300px|right|thumb]] |
+ | * '''P4''': 6-pin plug-on screw terminal for internal connections. | ||
+ | **Pin 1/4: Input for PTT from headset and restoring Factory Default Setting. | ||
+ | **Pin 2/4: Call button no. 2 or logical input (optional). | ||
+ | **Pin 3/4: Connected to hook-switch (reed-switch) | ||
+ | **Pin 5/6: Station LED for call and message info. (Pin 6 is positive.) | ||
− | + | * '''TP1/2''': Audio output to handset speaker (0 dB, 600 ohm balanced). | |
− | For | + | |
+ | For more details see [[INCA Substation Board Connectors]]. | ||
[[Category: INCA Connections]] | [[Category: INCA Connections]] |
Latest revision as of 14:10, 5 February 2018
Main connectors
To access these connectors the frontplate must be removed.
LAN | 10/100 Mbps RJ-45 port for LAN (uplink) connection. Supports PoE (802.3af). Draws power from either spare line or signal line. |
AUX | 10/100 Mbps RJ-45 ports for auxiliary equipment such as PC and IP camera. |
Input/Output | Pluggable screw terminal |
Local Power | Plugable screw terminal, 19-27 VDC Idle 4W, max. 8W |
Power Supply
The IP Heavy Duty Station supports Power over Ethernet (PoE, IEEE 802.3 a-f) where power can be drawn from either the spare line or signal line.
If PoE is not available, the IP Substation can be connected to a 24 VDC local power supply.
Connections
There are four connectors on the IP heavy Duty station PCB: P1-P4.
- P1 RJ45 LAN port is for connecting to the data network
- P2: RJ45 AUX port is for connecting to auxiliary equipment such as a PC
- P3: 6-pin plug-on screw terminal for external connections.
- Pin 1/2: Connection of external 8 ohm loudspeaker (optional).
- Pin 3/4: Internal NO relay contact for additional call indication, etc.
- Pin 5/6: Connect 24VDC power supply if PoE is not used
- P4: 6-pin plug-on screw terminal for internal connections.
- Pin 1/4: Input for PTT from headset and restoring Factory Default Setting.
- Pin 2/4: Call button no. 2 or logical input (optional).
- Pin 3/4: Connected to hook-switch (reed-switch)
- Pin 5/6: Station LED for call and message info. (Pin 6 is positive.)
- TP1/2: Audio output to handset speaker (0 dB, 600 ohm balanced).
For more details see INCA Substation Board Connectors.