Difference between revisions of "IP Substation Board Connection"
From Zenitel Wiki
| Line 15: | Line 15: | ||
|- | |- | ||
|'''P3''': || 6-pin plug-on screw terminal for external connections. | |'''P3''': || 6-pin plug-on screw terminal for external connections. | ||
| + | |- | ||
| + | | Pin 1/2: Connect 24 VDC for station power if power is not distributed via LAN. Pin 1 is positive. | ||
| + | |- | ||
| + | | Pin 3/4: Internal NO relay contact for door lockcontrol etc. | ||
| + | |- | ||
| + | | Pin 5/6: Normally connected to station loudspeaker. | ||
|- | |- | ||
|'''P4''': || 6-pin plug-on screw terminal for internal connections. | |'''P4''': || 6-pin plug-on screw terminal for internal connections. | ||
| Line 29: | Line 35: | ||
This port has not an individual IP address or power for aux equipment. | This port has not an individual IP address or power for aux equipment. | ||
P3: 6-pin plug-on screw terminal for external connections. | P3: 6-pin plug-on screw terminal for external connections. | ||
| − | Pin 1/2: Connect 24 VDC for station power if | + | Pin 1/2: Connect 24 VDC for station power if power is not distributed via LAN. Pin 1 is positive. |
| − | + | Pin 3/4: Internal NO relay contact for door lockcontrol etc. | |
| − | + | Pin 5/6: Normally connected to station loudspeaker. | |
| − | Pin 3/4: Internal NO relay contact for door | ||
| − | |||
| − | Pin 5/6: Normally connected to station | ||
| − | |||
May be used for 16-20 ohm/2 W external loudspeaker in parallel. | May be used for 16-20 ohm/2 W external loudspeaker in parallel. | ||
P4: 6-pin plug-on screw terminal for internal connections. | P4: 6-pin plug-on screw terminal for internal connections. | ||
Revision as of 20:53, 10 October 2007
There are four connectors on the IP substation board, P1-P4.
| P1: | RJ45 connector for LAN connection. |
| The station can be powered from this connection if the line supports Power over Ethernet. | |
| P2: | RJ45 connector for auxiliary LAN equipment like TV camera, PC or a second IP station. |
| This port has not an individual IP address or power for aux equipment. | |
| P3: | 6-pin plug-on screw terminal for external connections. |
| Pin 1/2: Connect 24 VDC for station power if power is not distributed via LAN. Pin 1 is positive. | |
| Pin 3/4: Internal NO relay contact for door lockcontrol etc. | |
| Pin 5/6: Normally connected to station loudspeaker. | |
| P4: | 6-pin plug-on screw terminal for internal connections. |
| When change to OFF: | When the "microphone alive" LED of the station goes OFF |
| When related to: | N/A |
P1: RJ45 connector for LAN connection The station can be powered from this connection if the line supports Power over Ethernet. P2: RJ45 connector for auxiliary LAN equipment like TV camera, PC or a second IP station. This port has not an individual IP address or power for aux equipment. P3: 6-pin plug-on screw terminal for external connections. Pin 1/2: Connect 24 VDC for station power if power is not distributed via LAN. Pin 1 is positive. Pin 3/4: Internal NO relay contact for door lockcontrol etc. Pin 5/6: Normally connected to station loudspeaker. May be used for 16-20 ohm/2 W external loudspeaker in parallel. P4: 6-pin plug-on screw terminal for internal connections. Pin 1/4: Call button no.1. Pin 2/4: Call button no.2 if included Pin 3/4: Call button no.3 if included Pin 5/6: Station LED for call and message info. TP1/2: Optional external audio output. This is a 0 dB, 600 ohm balanced output for connection to a power amplifier. Note that the amplifier input MUST HAVE AN INSULATED INPUT (trafo, capacitors, etc.).