Difference between revisions of "INCA Master Station Kit Board Connectors"

Latest revision as of 10:43, 21 November 2023

This chapter gives details about connections and indications for:

1 P1 LAN port & P2 AUX port
2 P3 - External Loudspeaker, Relay Output and External Power Input
3 P4 - Inputs and Station LED
4 J4, J40 & J41 - Keyboard and DAK LED
5 J5 - Display
6 J1 - DAK48 Module
7 J7 - Gooseneck Microphone
8 J8 - Handset and Headset
9 J9 - External Amplifier
10 J10 - Microphone
11 J11, J12 & J13 - Handset
12 S1 - Microphone Selection
13 S3 - Future use

P1 LAN port & P2 AUX port

P1:

LAN connector for 10/100 Mbit Ethernet connection. The station can be powered from this connection if the line supports Power over Ethernet (PoE).

The connector has two LEDs in front where the right (R) LED indicates Ethernet speed and the left (L) LED verifies Ethernet link and traffic. (L and R as seen from the connector side)

P2:

RJ45 connector for auxiliary equipment like IP camera, PC or a second IP station. This port does not have an individual IP address. It does not carry power for AUX equipment.

P1/P2

P3 - External Loudspeaker, Relay Output and External Power Input

6-pin plug-on screw terminal for external connections.

P3

Pin 1/2 Connect to 1.5 W loudspeaker.
- Typical impedance: 8 Ω
- Recommended impedance: 6-25 Ω.
Pin 3/4 Internal NO relay contact for door lock control etc.
Pin 5/6 Connect 24 VDC for station power if PoE is not used. Pin 6 is positive.

P4 - Inputs and Station LED

6-pin plug-on screw terminal for external connections.

P4

Pin 1/4 Input 1
Pin 2/4 Input 2
Pin 3/4 Input 3
Pin 5/6 Station LED for call message info.

When "Station Type" is set as Master station in AlphaPro, the inputs are mapped as DAK 11, 12 and 13.
When the "Station Type" is set as CRM in AlphaPro, the inputs are mapped as 251, 252 and 253.

J4, J40 & J41 - Keyboard and DAK LED

Keyboard matrix is available on connector J4 and on connector J40. Pin 1-9 is used.

In software you can choose between four different matrix types, see Keyboard Settings.

"Standard matrix" pinout on J4 and J40

J4 - Keyboard matrix

18-pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.

J4

J40 - Keyboard matrix

J40 provides an optional keyboard connection on a pinheader.

J4 and J41 - DAK LED connection

Optional DAK LED connection. Connection to J40/J41 can either be to a pin header or soldered directly to holes in the PCB.

J4/10 - J41/1 DAK1 Green LED
J4/11 - J41/2 DAK1 Red LED
J4/12 - J41/3 DAK2 Green LED
J4/13 - J41/4 DAK2 Red LED
J4/14 - J41/5 DAK3 Green LED
J4/15 - J41/6 DAK3 Red LED
J4/16 - J41/7 DAK4 Green LED
J4/17 - J41/8 DAK4 Red LED
J4/18 - J41/9 Common +3.3 V

The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAKs 1 to 4 and Soft keys 1 to 4 are used in current master stations.

Privacy on/off is accomplished by pressing the C key for 2 seconds. A circled P is shown in the display during Privacy mode.

J5 - Display

20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 100 8099 000).

J1 - DAK48 Module

RJ45 Connector for I2C interface. Used for connection of DAK modules.

J1

Pin 1 GND
Pin 2 A0 (GND)
Pin 3 A1 (GND)
Pin 4 NC (GND)
Pin 5 IRQ
Pin 6 SCL (Clock)
Pin 7 SDA (Data)
Pin 8 +13 V

J7 - Gooseneck Microphone

3-pin header for connecting gooseneck microphone.

J7

Pin 1 MIC+
Pin 2 MIC-
Pin 3 GND

J8 - Handset and Headset

Dual RJ11 for handset and headset. Handset can optionally be connected via J11, J12 and J13.

Handset:

J8

Pin 1 Mic+
Pin 2 Spk+
Pin 3 Spk- (0 V)
Pin 4 Mic-
Pin 5 Hook-switch (must be connected to pin 6 via a switch)
Pin 6 Hook-switch Ground

On PCB version 8023 ver.4 and earlier, the Hook-switch had to be connected between pin 5 and 3, not between pin 5 and 6.

Headset:

J8

Pin 7 Mic+
Pin 8 Spk+
Pin 9 Spk-
Pin 10 Mic-
Pin 11 PTT Ground
Pin 12 PTT (Not currently supported by SW)

J9 - External Amplifier

6-pin header for connecting external amplifier. 12V/5W can be supplied to the external amplifier. Signal to amplifier is balanced 0dBm 600 ohm.

J9

Pin 1 +13 V max. 500 mA to amplifier
Pin 2 LSN negative line
Pin 3 LSP positive line
Pin 4 GND
Pin 5 AMP_EN enable signal to amplifier
Pin 6 AMP_ERR error signal from amplifier

J10 - Microphone

Internal microphone

J10

Pin 1 MIC+
Pin 2 MIC-

J11, J12 & J13 - Handset

Pin header for handset connection. Same as J8 pin 1 - 6.

J11, J12, J13

J11 Pin 1 Spk+
J11 Pin 2 Spk-
J12 Pin 1 Mic+
J12 Pin 2 Mic-
J13 Pin 1 OFFHOOK
J13 Pin 2 GND
J13 Pin 3 PTT (Not currently supported by SW)

S1 - Microphone Selection

Slide-switch to select internal microphone (Int) or gooseneck microphone (Ext).

S1

S3 - Future use

4-way DIP switch for future use. Leave all in default OFF position.

S3

@@ Line 38: / Line 38: @@
 *Pin 5/6  Station LED for call message info.
-'''NOTE:'''
+{{Note|
- When the station is set as "Station Type" = '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.
+* ''When "Station Type" is set as '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.''
- When the station is set as "Station Type" = '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.
+* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.'' }}
-====J4, J40 & J41 - Keyboard====
+====J4, J40 & J41 - Keyboard and DAK LED====
-J4 & J40, pin 1-9, Keyboard matrix:
+Keyboard matrix is available on connector J4 and on connector J40. Pin 1-9 is used.
-[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|J4 and J40 pin matrix]]
+In software you can choose between four different matrix types, see [[Keyboard Settings]].
+[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|"Standard matrix" pinout on J4 and J40]]
 <br style="clear:both;" />
-'''J4'''
+'''J4 - Keyboard matrix'''
 -pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.
@@ Line 55: / Line 57: @@
 <br style="clear:both;" />
-'''J40'''
+'''J40 - Keyboard matrix'''
-Optional keyboard connection.
+J40 provides an optional keyboard connection on a pinheader.
-'''J41'''
+'''J4 and J41 - DAK LED connection'''
 Optional DAK LED connection. Connection to J40/J41 can either be to a pin header or soldered directly to holes in the PCB.
-J4 & J40 pin1-9  Keyboard matrix:
 *J4/10 - J41/1   DAK1 Green LED
 *J4/11 - J41/2   DAK1 Red LED
@@ Line 76: / Line 77: @@
 The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAKs 1 to 4 and Soft keys 1 to 4 are used in current master stations.
-Privacy on/off is accomplished by pressing the C key for 3 seconds. A circled ''P'' is shown in the display during Privacy mode.
+Privacy on/off is accomplished by pressing the C key for 2 seconds. A circled ''P'' is shown in the display during Privacy mode.
 <br style="clear:both;" />
@@ Line 114: / Line 115: @@
 *Pin 3  Spk- (0 V)
 *Pin 4  Mic-
-*Pin 5  Hook-switch (must be connected to pin 3 with a switch)
+*Pin 5  Hook-switch (must be connected to pin 6 via a switch)
-*Pin 6  PTT (Not currently supported by SW)
+*Pin 6   Hook-switch Ground
 See also: [[IP Flush Master and IP Flush Handset compatibility]]
+{{note| On PCB version 8023 ver.4 and earlier, the Hook-switch had to be connected between pin 5 and 3, not between pin 5 and 6.}}
 <u>'''Headset:'''</u>