Actions

Difference between revisions of "IP Flush Master -V2 Board Connectors"

From Zenitel Wiki

 
(39 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
{{AEIS}}This chapter gives details about connections and indications for:
 
{{AEIS}}This chapter gives details about connections and indications for:
*[[IP Flush Master -V2]]
 
  
[[File:IPFlushMasterKitPCB2.png|700px|right]]
+
*[[IP Flush Master -V2]]
 +
*[[IP-CROR]]
 +
*[[IP Master Station Kit - 1008493000|IP Master Station Kit -V2]]
 +
<br clear=all/>
 +
__NOTOC__
  
====P1 LAN port & P2 AUX port====
+
[[File:IPFlushDrawingwith numbers.png|thumb|left|800px]]
<u>'''P1:'''</u>
+
<br clear=all/>
  
LAN connector for 10/100 Mbit Ethernet connection. The station can be powered from this connection if the line supports Power over Ethernet (PoE).
+
{| border="1" }
 +
| align="center" style="background:#ffd400;" |'''Item'''
 +
| align="center" style="background:#ffd400;" |'''Description'''
 +
| align="center" style="background:#ffd400;" |'''''Comment'''''
 +
|-
 +
| P3 || Pluggable screw connector || * 1/2 = Connection to internal loudspeaker (8ohm) <br> * 3/4 = Relay <br> * 5/6 = Not in use
 +
|-
 +
| P4 || Pluggable screw connector || * 1/2/ = Input 1-3 <br> * 4 = Common <br> * 5/6 = Station LED (5=A, 6=C)
 +
|-
 +
| J1 || [[IP Flush Master DAK-48 Module|D48 Expansion Module]] || RJ45 Connector to connect D48 modules, via I2C bus.
 +
|-
 +
| P14 || External loudspeaker || 3-pin screw connector for 8 ohm loudspeaker (max 5W). Operates in parallel with internal speaker.
 +
|-
 +
| J3 || 5VDC || 5 volt DC output
 +
|-
 +
| P1 || LAN Port || 10/100Mbps RJ-45 port for connection to the network. Supports PoE (802.3af). Draws power from either spare line or signal line.
 +
|-
 +
| P2 || AUX Port || 10/100Mbps RJ-45 port for for auxiliary equipment such as PC and IP camera. PoE is not forwarded to this port.
 +
|-
 +
| P600 || External Power Supply || 2-pin screw connector for connecting external 24-48VDC power supply. Max 300mA.
 +
|-
 +
| J5 || Display || 20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
 +
|-
 +
| P5 || Keyboard || Solderpoints See details further down.
 +
|-
 +
| J4 || Keyboard || 18 pin ZIF connector. See details further down.
 +
|-
 +
| J8 || Handset/Headset || Dual RJ11 for Handset and Headset. See details further down.
 +
|-
 +
| J7 || Gooseneck || 3-pin header for connecting gooseneck microphone. 1 is +, 2 is - and 3 is GND.
 +
|-
 +
| S1 || Microphone selector || Slide switch to select internal microphone (int) or gooseneck microphone (ext)
 +
|-
 +
| J10 || Microphone || Internal microphone. Pin 1 is + and 2 is -.
 +
|-
 +
|}
  
The connector has two LEDs in front where the right (R) LED indicates Ethernet speed and the left (L) LED verifies Ethernet link and traffic. (L and R as seen from the connector side)
+
==Inputs==
 +
{{Note|
 +
* ''When "Station Type" is set as '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.''
 +
* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.''
 +
}}
  
<u>'''P2:'''</u>
+
==Keyboard matrix==
 
+
[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|P5 or J4 keyboard matrix]]
RJ45 connector for auxiliary equipment like IP camera, PC or a second IP station. This port does not have an individual IP address. It does not carry power for AUX equipment.
 
[[File:IP Master Board 1.PNG|left|thumb|200px|P1/P2]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
====P3 - Internal Loudspeaker, Relay Output and External Power Input====
+
'''P5 pinnings:'''
6-pin plug-on screw terminal for external connections.
+
[[File:IPFlushMasterPCB P5 new.png|left|thumb|300px|Pinout on P5]]
[[File:IPFlushMasterPCB_P3.png|left|thumb|200px|P3]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
*Pin 1/2  Connect to the internal loudspeaker. 
 
**Typical impedance: 8 Ω
 
**Recommended impedance: 6-25 Ω.
 
*Pin 3/4  Internal NO relay contact for door lock control etc.
 
*Pin 5/6  Not in use.
 
 
====P4 - Inputs and Station LED====
 
6-pin plug-on screw terminal for external connections.
 
[[File:IP Master Board 3.PNG|thumb|left|200px|P4]]
 
<br style="clear:both;" />
 
*Pin 1/4  Input 1
 
*Pin 2/4  Input 2
 
*Pin 3/4  Input 3
 
*Pin 5/6  Station LED for call message info.
 
 
{{Note|
 
* ''When "Station Type" is set as '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.''
 
* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.'' }}
 
 
====J4/P5 - Keyboard and DAK LED====
 
 
Keyboard matrix is available on connector J4. Pin 1-9 is used.
 
  
 +
'''J4 connector'''
 
In software you can choose between four different matrix types, see [[Keyboard Settings]].
 
In software you can choose between four different matrix types, see [[Keyboard Settings]].
 
[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|"Standard matrix" pinout on J4]]
 
<br style="clear:both;" />
 
 
'''J4 - Keyboard matrix'''
 
  
 
18-pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.
 
18-pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.
Line 55: Line 68:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
'''P5 - Keyboard'''
+
*J4/10  DAK1 Green LED
[[File:IPFlushMasterPCB P5.png|left|thumb|300px|Pinout on P5]]
+
*J4/11  DAK1 Red LED
<br style="clear:both;" />
+
*J4/12  DAK2 Green LED
 
+
*J4/13  DAK2 Red LED
'''J4 - DAK LED connection'''
+
*J4/14  DAK3 Green LED
 
+
*J4/15  DAK3 Red LED
Optional DAK LED connection.
+
*J4/16  DAK4 Green LED
 
+
*J4/17  DAK4 Red LED
*J4/10  DAK1 Green LED
 
*J4/11  DAK1 Red LED
 
*J4/12  DAK2 Green LED
 
*J4/13  DAK2 Red LED
 
*J4/14  DAK3 Green LED
 
*J4/15  DAK3 Red LED
 
*J4/16  DAK4 Green LED
 
*J4/17  DAK4 Red LED
 
 
*J4/18  Common +3.3 V
 
*J4/18  Common +3.3 V
The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAKs 1 to 4 and Soft keys 1 to 4 are used in current master stations.
 
 
Privacy on/off is accomplished by pressing the C key for 3 seconds. A circled ''P'' is shown in the display during Privacy mode.
 
<br style="clear:both;" />
 
  
====J5 - Display====
+
==Handset and Headset==
20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 100 8099 000).
+
''Handset can optionally be connected via J11, J12 and J13.''
<br style="clear:both;" />
 
  
====J1 - DAK48 Module====
+
'''J11, J12 & J13 - Handset'''
RJ45 Connector for I2C interface. Used for connection of DAK modules.
 
[[File:IP Master Board 5.PNG|left|thumb|200px|J1]]
 
<br style="clear:both;" />
 
*Pin 1  GND
 
*Pin 2  A0 (GND)
 
*Pin 3  A1 (GND)
 
*Pin 4  NC (GND)
 
*Pin 5  IRQ 
 
*Pin 6  SCL (Clock)
 
*Pin 7  SDA (Data)
 
*Pin 8  +13 V
 
  
====J7 - Gooseneck Microphone====
+
Pin header for handset connection. Same as J8 pin 1 - 6.
3-pin header for connecting gooseneck microphone.
+
[[File:IPFlushMasterPCB J11-13.png|left|thumb|400px|J11, J12, J13]]
[[File:IP Master Board 6.PNG|left|thumb|200px|J7]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
*Pin 1  MIC+
 
*Pin 2  MIC-
 
*Pin 3  GND
 
  
====J8 - Handset and Headset====
+
*J11  Pin 1  Spk+
Dual RJ11 for handset and headset. ''Handset can optionally be connected via J11, J12 and J13.''
+
*J11  Pin 2  Spk-
 +
*J12  Pin 1  Mic+
 +
*J12   Pin 2  Mic-
 +
*J13  Pin 1  OFFHOOK
 +
*J13   Pin 2  GND
  
 
<u>'''Handset:'''</u>
 
<u>'''Handset:'''</u>
 
[[File:IP Master Board 7.PNG|left|thumb|200px|J8]]
 
[[File:IP Master Board 7.PNG|left|thumb|200px|J8]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
*Pin 1  Mic+  
+
 
*Pin 2  Spk+  
+
*Pin 1  Mic+
*Pin 3  Spk- (0 V)  
+
*Pin 2  Spk+
*Pin 4  Mic-
+
*Pin 3  Spk- (0 V)
*Pin 5  Hook-switch (must be connected to pin 6 via a switch)  
+
*Pin 4  Mic-
 +
*Pin 5  Hook-switch (must be connected to pin 6 via a switch)
 
*Pin 6  Hook-switch Ground
 
*Pin 6  Hook-switch Ground
  
Line 118: Line 108:
 
[[File:IP Master Board 8.PNG|left|thumb|200px|J8]]
 
[[File:IP Master Board 8.PNG|left|thumb|200px|J8]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
*Pin 7  Mic+  
+
 
*Pin 8  Spk+  
+
*Pin 7  Mic+
*Pin 9  Spk-  
+
*Pin 8  Spk+
*Pin 10  Mic-
+
*Pin 9  Spk-
*Pin 11  PTT Ground  
+
*Pin 10  Mic-
 +
*Pin 11  PTT Ground
 
*Pin 12  PTT (Not currently supported by SW)
 
*Pin 12  PTT (Not currently supported by SW)
  
==== P14 - External loudspeaker ====
+
{{Note|
3-pin screw connector for connecting external 8 ohm loudspeaker, max 5W. Operates in parallel with built-in speaker.
+
Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
 
+
}}
*Pin 2/3: 8 Ohm loudspeaker
+
<br clear=all/>
 
 
====J10 - Microphone====
 
Internal microphone
 
[[File:IP Master Board 10.PNG|left|thumb|200px|J10]]
 
<br style="clear:both;" />
 
*Pin 1  MIC+
 
*Pin 2  MIC-
 
 
 
====J11, J12 & J13 - Handset====
 
Pin header for handset connection. Same as J8 pin 1 - 6.
 
[[File:IP Master Board 11.PNG|left|thumb|200px|J11, J12, J13]]
 
<br style="clear:both;" />
 
*J11  Pin 1  Spk+
 
*J11  Pin 2  Spk-   
 
*J12  Pin 1  Mic+
 
*J12  Pin 2  Mic-
 
*J13  Pin 1  OFFHOOK 
 
*J13  Pin 2  GND
 
*J13  Pin 3  PTT (Not currently supported by SW)
 
 
 
====S1 - Microphone Selection====
 
Slide-switch to select internal microphone (Int) or gooseneck microphone (Ext).
 
[[File:IP Master Board 12.PNG|left|thumb|200px|S1]]
 
<br style="clear:both;" />
 
 
 
 
 
  
  
 
[[Category:Turbine Connections]]
 
[[Category:Turbine Connections]]

Latest revision as of 08:51, 17 October 2024

AEIS.png

This chapter gives details about connections and indications for:



IPFlushDrawingwith numbers.png


Item Description Comment
P3 Pluggable screw connector * 1/2 = Connection to internal loudspeaker (8ohm)
* 3/4 = Relay
* 5/6 = Not in use
P4 Pluggable screw connector * 1/2/ = Input 1-3
* 4 = Common
* 5/6 = Station LED (5=A, 6=C)
J1 D48 Expansion Module RJ45 Connector to connect D48 modules, via I2C bus.
P14 External loudspeaker 3-pin screw connector for 8 ohm loudspeaker (max 5W). Operates in parallel with internal speaker.
J3 5VDC 5 volt DC output
P1 LAN Port 10/100Mbps RJ-45 port for connection to the network. Supports PoE (802.3af). Draws power from either spare line or signal line.
P2 AUX Port 10/100Mbps RJ-45 port for for auxiliary equipment such as PC and IP camera. PoE is not forwarded to this port.
P600 External Power Supply 2-pin screw connector for connecting external 24-48VDC power supply. Max 300mA.
J5 Display 20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
P5 Keyboard Solderpoints See details further down.
J4 Keyboard 18 pin ZIF connector. See details further down.
J8 Handset/Headset Dual RJ11 for Handset and Headset. See details further down.
J7 Gooseneck 3-pin header for connecting gooseneck microphone. 1 is +, 2 is - and 3 is GND.
S1 Microphone selector Slide switch to select internal microphone (int) or gooseneck microphone (ext)
J10 Microphone Internal microphone. Pin 1 is + and 2 is -.

Inputs

Note icon
  • When "Station Type" is set as Master station in AlphaPro, the inputs are mapped as DAK 11, 12 and 13.
  • When the "Station Type" is set as CRM in AlphaPro, the inputs are mapped as 251, 252 and 253.


Keyboard matrix

P5 or J4 keyboard matrix


P5 pinnings:

Pinout on P5


J4 connector In software you can choose between four different matrix types, see Keyboard Settings.

18-pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.

J4


  • J4/10 DAK1 Green LED
  • J4/11 DAK1 Red LED
  • J4/12 DAK2 Green LED
  • J4/13 DAK2 Red LED
  • J4/14 DAK3 Green LED
  • J4/15 DAK3 Red LED
  • J4/16 DAK4 Green LED
  • J4/17 DAK4 Red LED
  • J4/18 Common +3.3 V

Handset and Headset

Handset can optionally be connected via J11, J12 and J13.

J11, J12 & J13 - Handset

Pin header for handset connection. Same as J8 pin 1 - 6.

J11, J12, J13


  • J11 Pin 1 Spk+
  • J11 Pin 2 Spk-
  • J12 Pin 1 Mic+
  • J12 Pin 2 Mic-
  • J13 Pin 1 OFFHOOK
  • J13 Pin 2 GND

Handset:

J8


  • Pin 1 Mic+
  • Pin 2 Spk+
  • Pin 3 Spk- (0 V)
  • Pin 4 Mic-
  • Pin 5 Hook-switch (must be connected to pin 6 via a switch)
  • Pin 6 Hook-switch Ground

Headset:

J8


  • Pin 7 Mic+
  • Pin 8 Spk+
  • Pin 9 Spk-
  • Pin 10 Mic-
  • Pin 11 PTT Ground
  • Pin 12 PTT (Not currently supported by SW)
Note icon

Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)