Actions

Difference between revisions of "AMC Flash Image update from Redboot"

From Zenitel Wiki

(Complete FLASH image)
(Complete FLASH image)
 
(18 intermediate revisions by 4 users not shown)
Line 1: Line 1:
 +
{{A}}
 
This article describes how to upgrade the AMC-IP Flash Image from [[Redboot]], using Linux console, Ethernet and TFTP transfer. A complete FLASH image (32MB) [[Board Support Package]], is written to the flash on-board.
 
This article describes how to upgrade the AMC-IP Flash Image from [[Redboot]], using Linux console, Ethernet and TFTP transfer. A complete FLASH image (32MB) [[Board Support Package]], is written to the flash on-board.
  
 
'''Note:''' The recommended way to upgrade the Flash Image is by using the dedicated [[AMC Flash Image update|PC application "AlphaCom Image Upgrade"]]. However, the PC application requires that the AMC-IP is fully operational with AMC software 10.52 or higher. If the AMC-IP board is not fully operational (e.g. corrupt file system, AMC application fails to start etc.) the procedure described in this article must be used.
 
'''Note:''' The recommended way to upgrade the Flash Image is by using the dedicated [[AMC Flash Image update|PC application "AlphaCom Image Upgrade"]]. However, the PC application requires that the AMC-IP is fully operational with AMC software 10.52 or higher. If the AMC-IP board is not fully operational (e.g. corrupt file system, AMC application fails to start etc.) the procedure described in this article must be used.
  
== AMC-IP hardware preparation ==
+
==AMC-IP hardware preparation==
[[Image:AMC-IP switch settings.png|right|150px|thumb|AMC-IP switch and jumper settings]]
+
[[Image:AMC-IP switch settings.png|thumb|left|500px|AMC-IP switch and jumper settings]]
* Turn switch S601 – 1 to ON (enable Linux consol on serial port 1)
+
<br style="clear:both;" />
* Move jumper S700 to upper position (1 – 2) to disable the watchdog
 
  
== Setup ==
+
*Turn switch S601 – 1 to ON (enable Linux consol on serial port 1)
 +
*Move jumper S700 to upper position (1 – 2) to disable the watchdog
 +
 
 +
==Setup==
  
 
  |----|  RS-232 (115200,8-N-1)  |--------|
 
  |----|  RS-232 (115200,8-N-1)  |--------|
Line 22: Line 25:
 
*The RS-232 and Ethernet links can either be on the same PC or different PCs.
 
*The RS-232 and Ethernet links can either be on the same PC or different PCs.
  
== Image files ==
+
==Image files==
 
What image file to use depends on the hardware version of the AMC-IP board. There are two main hardware versions, easily distinguished from each other by the color of the printed circuit bord (PCB). The oldest hardware version (PCB 8000/1 to 8000/4) has red PCB. The newest hardware version (PCB 8000/5 and 8000/6) has black PCB.
 
What image file to use depends on the hardware version of the AMC-IP board. There are two main hardware versions, easily distinguished from each other by the color of the printed circuit bord (PCB). The oldest hardware version (PCB 8000/1 to 8000/4) has red PCB. The newest hardware version (PCB 8000/5 and 8000/6) has black PCB.
  
=== Black AMC-IP board ===
+
===Black AMC-IP board===
* Download the AMC IP Flash Image file '''axeu_b3000_a1100300.aimg''' from the [[Downloads|download page]]
+
 
* If you use Internet Explorer the file will automatically be stored with the file extension .zip on your PC. If not, rename the file extension from .aimg to .zip.
+
*Download the AMC IP Flash Image file '''axeu_b3000_a1100300.aimg''' from the [[Downloads|download page]]
* Unzip the file. It consists of two files, a aimg.xml file and a '''axeu_b3000_a1100300.bin''' file. Store the files on a folder on the PC (e.g. c:\work\amc_images)
+
*If you use Internet Explorer the file will automatically be stored with the file extension .zip on your PC. If not, rename the file extension from .aimg to .zip.
 +
*'''Unzip the file'''. It consists of two files, a aimg.xml file and a '''axeu_b3000_a1100300.bin''' file. Store the files on a folder on the PC (e.g. c:\work\amc_images)
 +
*'''Note, you must unzip the file to extract the .bin file.  Failure to do this will cause a failure to upload the flash image!'''
  
=== Red AMC-IP board ===
+
===Red AMC-IP board===
  
 
Which image file to use depends on the version of RedBoot already installed on the board.
 
Which image file to use depends on the version of RedBoot already installed on the board.
Line 47: Line 52:
 
  Platform: IXDP425 Development Platform (XScale) BE
 
  Platform: IXDP425 Development Platform (XScale) BE
 
  Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
 
  Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
 +
 +
*If the Redboot version is ACE 09 or newer:
 +
**Download the AMC IP Flash Image file '''axeu_b2200_a1100300.aimg''' from the [[Downloads|download page]]
 +
**If you use Internet Explorer the file will automatically be stored with the file extension .zip on your PC. If not, rename the file extension from .aimg to .zip.
 +
**'''Unzip the file'''. It consists of two files, a aimg.xml file and a '''axeu_b2200_a1100300.bin''' file. Store the files on a folder on the PC (e.g. c:\work\amc_images)
 +
**'''Note, you must unzip the file to extract the .bin file.  Failure to do this will cause a failure to upload the flash image!'''
  
 
*If the Redboot version is ACE 08 or older:
 
*If the Redboot version is ACE 08 or older:
** Download the AMC IP Flash Image file '''alpha_uimage_16_rba08.bin''' from the [[Downloads|download page]]
+
**Download the AMC IP Flash Image file '''alpha_uimage_16_rba08.bin''' from the [[Downloads|download page]]
** Unzip the downloaded file and store it on a folder on the PC (e.g. c:\work\amc_images)
+
**Unzip the downloaded file and store it on a folder on the PC (e.g. c:\work\amc_images)
  
*If the Redboot version is ACE 09 or newer:
+
==TFTP Server==
** Download the AMC IP Flash Image file '''axeu_b2200_a1100300.aimg''' from the [[Downloads|download page]]
 
** If you use Internet Explorer the file will automatically be stored with the file extension .zip on your PC. If not, rename the file extension from .aimg to .zip.
 
*** Unzip the file. It consists of two files, a aimg.xml file and a '''axeu_b2200_a1100300.bin''' file. Store the files on a folder on the PC (e.g. c:\work\amc_images)
 
 
 
== TFTP Server ==
 
 
A TFTP server has to be installed on the PC. A recommended TFTP server for windows is tftp32 from [http://tftpd32.jounin.net/ http://tftpd32.jounin.net]
 
A TFTP server has to be installed on the PC. A recommended TFTP server for windows is tftp32 from [http://tftpd32.jounin.net/ http://tftpd32.jounin.net]
  
Line 68: Line 74:
 
The TFTP Server program must be running during the Image upgrade process.
 
The TFTP Server program must be running during the Image upgrade process.
  
== RedBoot init ==
+
==RedBoot init==
'''Note:''' Avoid using arrow- and special keys with redboot!
+
{{Note|Avoid using arrow and special keys with redboot!}}
  
 
Open a serial console to the AMC-IP board (e.g. HyperTerminal or Terra Term). Communication parameters: 115200 baud, no parity, 8 data bits, 1 stop bit.
 
Open a serial console to the AMC-IP board (e.g. HyperTerminal or Terra Term). Communication parameters: 115200 baud, no parity, 8 data bits, 1 stop bit.
Line 81: Line 87:
 
Wait for the RedBoot prompt (this can take some time):
 
Wait for the RedBoot prompt (this can take some time):
  
Redboot>  
+
{{code|Redboot>}}
  
 
Make sure the the ‘bootp’ parameter is set to ‘false’
 
Make sure the the ‘bootp’ parameter is set to ‘false’
  
Redboot> fconfig bootp
+
{{code|Redboot> fconfig bootp}}
  
 
If set to  'true' change to 'false' by using <backspace> to delete current setting and type in  false.  
 
If set to  'true' change to 'false' by using <backspace> to delete current setting and type in  false.  
Line 93: Line 99:
 
Make sure the network interface is set to ‘npe_eth0’:
 
Make sure the network interface is set to ‘npe_eth0’:
  
Redboot> fconfig net_device npe_eth0
+
{{code|Redboot> fconfig net_device npe_eth0}}
  
 
Clear the IP configuration in NVRAM:
 
Clear the IP configuration in NVRAM:
Redboot> mfill -b 0x5442ff00 -l 256 -p 0x0000 -2
+
{{code|Redboot> mfill -b 0x5442ff00 -l 256 -p 0x0000 -2}}
  
 
Configure the network address/mask for the AMC-IP board (replace example 10.5.220.13 with actual address):
 
Configure the network address/mask for the AMC-IP board (replace example 10.5.220.13 with actual address):
  
Redboot> fconfig bootp_my_ip 10.5.220.13
+
{{code|Redboot> fconfig bootp_my_ip 10.5.220.13}}
Redboot> fconfig bootp_my_ip_mask 255.255.255.0
+
{{code|Redboot> fconfig bootp_my_ip_mask 255.255.255.0}}
  
 
If you are connecting the AMC-board back-to-back with your PC we have standardized on a ‘Windows Automatic Private’ address IP:169.254.1.5/255.255.0.0
 
If you are connecting the AMC-board back-to-back with your PC we have standardized on a ‘Windows Automatic Private’ address IP:169.254.1.5/255.255.0.0
Line 109: Line 115:
 
If the TFTP server is in a different network, a gateway address has to be set up :
 
If the TFTP server is in a different network, a gateway address has to be set up :
  
Redboot> fconfig bootp_my_gateway_ip 10.5.220.1
+
{{code|Redboot> fconfig bootp_my_gateway_ip 10.5.220.1}}
  
 
Finally the IP-address of the server (i.e. the PC were the image files are located) has to be setup (replace example 10.5.220.101 with actual address):
 
Finally the IP-address of the server (i.e. the PC were the image files are located) has to be setup (replace example 10.5.220.101 with actual address):
  
Redboot> fconfig bootp_server_ip 10.5.220.101
+
{{code|Redboot> fconfig bootp_server_ip 10.5.220.101}}
  
  
 
The complete configuration can be listed:
 
The complete configuration can be listed:
  
Redboot> fconfig –l –n
+
{{code|Redboot> fconfig –l –n}}
  
 
To activate the settings:
 
To activate the settings:
  
Redboot> reset
+
{{code|Redboot> reset}}
  
 
Now the AMC board will reset. Press Ctrl + C within 3 seconds to log on to Redboot again.
 
Now the AMC board will reset. Press Ctrl + C within 3 seconds to log on to Redboot again.
Line 128: Line 134:
 
To test the IP connection to the server (use Ctrl-C to abort ping):
 
To test the IP connection to the server (use Ctrl-C to abort ping):
  
Redboot> ping –h <server-ip>  
+
{{code|Redboot> ping –h <server-ip>}}
  
''Note'': Make sure that the server is able to reply. The TFTP Server program must be running. If the OS is Windows XP you might need to stop the Windows Firewall temporarily.
+
{{Note|Make sure that the server is able to reply. The TFTP Server program must be running. If the OS is Windows XP you might need to stop the Windows Firewall temporarily.}}
  
 
Example:
 
Example:
  
RedBoot> ping -h 169.254.232.100
+
{{code|RedBoot> ping -h 169.254.232.100}}
 
  ''Immediate response: ''Network PING - from 169.254.1.5 to 169.254.232.100
 
  ''Immediate response: ''Network PING - from 169.254.1.5 to 169.254.232.100
 
  ''Response after 20 seconds: ''PING - received 10 of 10 expected
 
  ''Response after 20 seconds: ''PING - received 10 of 10 expected
  
== Complete FLASH image ==
+
==Complete FLASH image==
 
Load image without the Bootloader, unlock, erase and program (all but RedBoot):
 
Load image without the Bootloader, unlock, erase and program (all but RedBoot):
  
RedBoot> load -r -v -b 0x01008000 <xxx.bin>
+
{{code|RedBoot> load -r -v -b 0x01008000 <xxx.bin>}}
 
'''Black AMC-IP:'''
 
'''Black AMC-IP:'''
* <xxx.bin> = '''axeu_b3000_a1100300.bin'''
+
 
 +
*<xxx.bin> = '''axeu_b3001_a1101303.bin'''
  
 
'''Red AMC-IP:'''
 
'''Red AMC-IP:'''
*RedBoot version ACE 08 or earler on the AMC-IP board: <xxx.bin> = '''alpha_uimage_16_rba08.bin'''
+
 
 +
*RedBoot version ACE 08 or earlier on the AMC-IP board: <xxx.bin> = '''alpha_uimage_16_rba08.bin'''
 
*RedBoot version ACE 09 or newer on the AMC-IP board: <xxx.bin> = '''axeu_b2200_a1100300.bin'''. The .bin file must be unpacked from the .aimg file (like a .zip file) and stored in an apropriate folder
 
*RedBoot version ACE 09 or newer on the AMC-IP board: <xxx.bin> = '''axeu_b2200_a1100300.bin'''. The .bin file must be unpacked from the .aimg file (like a .zip file) and stored in an apropriate folder
 +
 
<br>
 
<br>
The load process takes approx. 1 minute, and should complete without any error messages. When finnished a message saying "''Raw file loaded 0x01008000-0x02f87fff, assumed entry at 0x01008000''" should be displayed, and the RedBoot promt should reappear. Now run the unlock command:
+
The load process takes approx. 1 minute, and should complete without any error messages. When finished a message saying "''Raw file loaded 0x01008000-0x02f87fff, assumed entry at 0x01008000''" should be displayed, and the RedBoot promt should reappear. Now run the unlock command:
RedBoot> fis unlock -f 0x50080000 -l 0x01f80000
+
{{code|RedBoot> fis unlock -f 0x50080000 -l 0x01f80000}}
 
The command should execute without any error messages, and the RedBoot promt should reappear. Run the erase command:
 
The command should execute without any error messages, and the RedBoot promt should reappear. Run the erase command:
RedBoot> fis erase -f 0x50080000 -l 0x01f80000  
+
{{code|RedBoot> fis erase -f 0x50080000 -l 0x01f80000}}
The erase process takes approx. 4 minutes, and the progress is shown by 'dots' on the terminal. It should complete without any error messages. When finnished the RedBoot promt will reappear. Now run the write command:
+
The erase process takes approx. 4 minutes, and the progress is shown by 'dots' on the terminal. It should complete without any error messages. When finished the RedBoot promt will reappear. Now run the write command:
RedBoot> fis write -b 0x01008000 -f 0x50080000 -l 0x01f80000  
+
{{code|RedBoot> fis write -b 0x01008000 -f 0x50080000 -l 0x01f80000}}
The write process takes approx. 4 minutes. The progress is indicated by repetitive dots on the terminal, and should complete without any error messages. When finnished the RedBoot promt will reappear.
+
The write process takes approx. 4 minutes. The progress is indicated by repetitive dots on the terminal, and should complete without any error messages.  
 +
When finished the RedBoot promt will reappear.
 +
 
 +
If the Program process stops with '''Err = 90''' it means that a sector in the flash memory is damaged, and the AMC board is history!
  
 
The upgrade of the Flash image is now completed.
 
The upgrade of the Flash image is now completed.
  
== Finalizing the AMC-IP ==
+
==Finalizing the AMC-IP==
 
Switch off the power and:
 
Switch off the power and:
* Turn switch S601 – 1 to OFF (disable Linux consol on serial port 1)
+
 
* Move jumper S700 to down position (2 – 3) to enable the watchdog
+
*Turn switch S601 – 1 to OFF (disable Linux consol on serial port 1)
 +
*Move jumper S700 to down position (2 – 3) to enable the watchdog
  
  
 
Use the [[AMC Flash Image update|PC application "AlphaCom Image Upgrade"]] to check if the Bootloader itself needs to be upgraded. In some cases AlphaCom features may also depend on the Bootloader version (such as hot stand-by mode). When the PC application connects to the AMC-IP it will read out the Bootloader version, and show in the status window if a bootloader upgrade is required or not. If required, run an Image Upgrade from the PC application.
 
Use the [[AMC Flash Image update|PC application "AlphaCom Image Upgrade"]] to check if the Bootloader itself needs to be upgraded. In some cases AlphaCom features may also depend on the Bootloader version (such as hot stand-by mode). When the PC application connects to the AMC-IP it will read out the Bootloader version, and show in the status window if a bootloader upgrade is required or not. If required, run an Image Upgrade from the PC application.
  
 
+
[[Category:Upgrade and Recovery]]
 
 
[[Category:AlphaCom E Software]]
 

Latest revision as of 08:24, 12 July 2023

AlphaCom icon 300px.png

This article describes how to upgrade the AMC-IP Flash Image from Redboot, using Linux console, Ethernet and TFTP transfer. A complete FLASH image (32MB) Board Support Package, is written to the flash on-board.

Note: The recommended way to upgrade the Flash Image is by using the dedicated PC application "AlphaCom Image Upgrade". However, the PC application requires that the AMC-IP is fully operational with AMC software 10.52 or higher. If the AMC-IP board is not fully operational (e.g. corrupt file system, AMC application fails to start etc.) the procedure described in this article must be used.

AMC-IP hardware preparation

AMC-IP switch and jumper settings


  • Turn switch S601 – 1 to ON (enable Linux consol on serial port 1)
  • Move jumper S700 to upper position (1 – 2) to disable the watchdog

Setup

|----|  RS-232 (115200,8-N-1)   |--------|
|    |--------------------------|S1      | 
| PC |                          | AMC-IP |   
|    |    Ethernet              |        |                 
|    |--------------------------|Eth0    |
|----|                          |--------|
  • On the AMC IP board use serial port 1 and ethernet port 0.
  • The RS-232 link is used for console (command prompt for RedBoot)
  • The Ethernet link is used for file transfer (TFTP transfer) of the image to flash.
  • The RS-232 and Ethernet links can either be on the same PC or different PCs.

Image files

What image file to use depends on the hardware version of the AMC-IP board. There are two main hardware versions, easily distinguished from each other by the color of the printed circuit bord (PCB). The oldest hardware version (PCB 8000/1 to 8000/4) has red PCB. The newest hardware version (PCB 8000/5 and 8000/6) has black PCB.

Black AMC-IP board

  • Download the AMC IP Flash Image file axeu_b3000_a1100300.aimg from the download page
  • If you use Internet Explorer the file will automatically be stored with the file extension .zip on your PC. If not, rename the file extension from .aimg to .zip.
  • Unzip the file. It consists of two files, a aimg.xml file and a axeu_b3000_a1100300.bin file. Store the files on a folder on the PC (e.g. c:\work\amc_images)
  • Note, you must unzip the file to extract the .bin file. Failure to do this will cause a failure to upload the flash image!

Red AMC-IP board

Which image file to use depends on the version of RedBoot already installed on the board.

You find the Redboot version by watching the Linux console during startup.

Example screenshot: Here RedBoot is version ACE 11:

Trying NPE-B...success. Using NPE-B with PHY 0.
Ethernet eth0: MAC address 00:02:b3:07:07:07
IP: 169.254.1.5/255.255.0.0, Gateway: 169.254.1.1
Default server: 16.254.1.10
.
RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 2.02 ACE 11 - built 10:41:17, Mar 12 2009
.
Platform: IXDP425 Development Platform (XScale) BE
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
  • If the Redboot version is ACE 09 or newer:
    • Download the AMC IP Flash Image file axeu_b2200_a1100300.aimg from the download page
    • If you use Internet Explorer the file will automatically be stored with the file extension .zip on your PC. If not, rename the file extension from .aimg to .zip.
    • Unzip the file. It consists of two files, a aimg.xml file and a axeu_b2200_a1100300.bin file. Store the files on a folder on the PC (e.g. c:\work\amc_images)
    • Note, you must unzip the file to extract the .bin file. Failure to do this will cause a failure to upload the flash image!
  • If the Redboot version is ACE 08 or older:
    • Download the AMC IP Flash Image file alpha_uimage_16_rba08.bin from the download page
    • Unzip the downloaded file and store it on a folder on the PC (e.g. c:\work\amc_images)

TFTP Server

A TFTP server has to be installed on the PC. A recommended TFTP server for windows is tftp32 from http://tftpd32.jounin.net

Unzip the files to a folder on the PC (e.g. c:\Program Files\tftpd32\) and run tftpd32.exe (no install).

Set the image folder (e.g. c:\work\amc_images) as ‘base directory’ in tftpd32 (use the ‘settings’ button).

Turn off the DHCP (also under 'settings') server part of the tftp32 application to avoid interfering with other DHCP servers in your network.

The TFTP Server program must be running during the Image upgrade process.

RedBoot init

Note icon Avoid using arrow and special keys with redboot!


Open a serial console to the AMC-IP board (e.g. HyperTerminal or Terra Term). Communication parameters: 115200 baud, no parity, 8 data bits, 1 stop bit.

Power On or reset the AMC-IP board. A ‘+’ sign in the console window indicates a reboot.

Press Ctrl + C within 3 seconds after the reset/power on.

When the RedBoot application starts you should also be able to see LED activate sequence on the front of the board.

Wait for the RedBoot prompt (this can take some time):

Redboot>


Make sure the the ‘bootp’ parameter is set to ‘false’

Redboot> fconfig bootp


If set to 'true' change to 'false' by using <backspace> to delete current setting and type in false.

In general use <backspace> to edit parameters displayed by the fconfig command

Make sure the network interface is set to ‘npe_eth0’:

Redboot> fconfig net_device npe_eth0


Clear the IP configuration in NVRAM:

Redboot> mfill -b 0x5442ff00 -l 256 -p 0x0000 -2


Configure the network address/mask for the AMC-IP board (replace example 10.5.220.13 with actual address):

Redboot> fconfig bootp_my_ip 10.5.220.13


Redboot> fconfig bootp_my_ip_mask 255.255.255.0


If you are connecting the AMC-board back-to-back with your PC we have standardized on a ‘Windows Automatic Private’ address IP:169.254.1.5/255.255.0.0

If you are connecting to a PC in a LAN you must find a free address in this LAN (check with your IT-administrator).

If the TFTP server is in a different network, a gateway address has to be set up :

Redboot> fconfig bootp_my_gateway_ip 10.5.220.1


Finally the IP-address of the server (i.e. the PC were the image files are located) has to be setup (replace example 10.5.220.101 with actual address):

Redboot> fconfig bootp_server_ip 10.5.220.101



The complete configuration can be listed:

Redboot> fconfig –l –n


To activate the settings:

Redboot> reset


Now the AMC board will reset. Press Ctrl + C within 3 seconds to log on to Redboot again.

To test the IP connection to the server (use Ctrl-C to abort ping):

Redboot> ping –h <server-ip>


Note icon Make sure that the server is able to reply. The TFTP Server program must be running. If the OS is Windows XP you might need to stop the Windows Firewall temporarily.


Example:

RedBoot> ping -h 169.254.232.100


Immediate response: Network PING - from 169.254.1.5 to 169.254.232.100
Response after 20 seconds: PING - received 10 of 10 expected

Complete FLASH image

Load image without the Bootloader, unlock, erase and program (all but RedBoot):

RedBoot> load -r -v -b 0x01008000 <xxx.bin>


Black AMC-IP:

  • <xxx.bin> = axeu_b3001_a1101303.bin

Red AMC-IP:

  • RedBoot version ACE 08 or earlier on the AMC-IP board: <xxx.bin> = alpha_uimage_16_rba08.bin
  • RedBoot version ACE 09 or newer on the AMC-IP board: <xxx.bin> = axeu_b2200_a1100300.bin. The .bin file must be unpacked from the .aimg file (like a .zip file) and stored in an apropriate folder


The load process takes approx. 1 minute, and should complete without any error messages. When finished a message saying "Raw file loaded 0x01008000-0x02f87fff, assumed entry at 0x01008000" should be displayed, and the RedBoot promt should reappear. Now run the unlock command:

RedBoot> fis unlock -f 0x50080000 -l 0x01f80000


The command should execute without any error messages, and the RedBoot promt should reappear. Run the erase command:

RedBoot> fis erase -f 0x50080000 -l 0x01f80000


The erase process takes approx. 4 minutes, and the progress is shown by 'dots' on the terminal. It should complete without any error messages. When finished the RedBoot promt will reappear. Now run the write command:

RedBoot> fis write -b 0x01008000 -f 0x50080000 -l 0x01f80000


The write process takes approx. 4 minutes. The progress is indicated by repetitive dots on the terminal, and should complete without any error messages. When finished the RedBoot promt will reappear.

If the Program process stops with Err = 90 it means that a sector in the flash memory is damaged, and the AMC board is history!

The upgrade of the Flash image is now completed.

Finalizing the AMC-IP

Switch off the power and:

  • Turn switch S601 – 1 to OFF (disable Linux consol on serial port 1)
  • Move jumper S700 to down position (2 – 3) to enable the watchdog


Use the PC application "AlphaCom Image Upgrade" to check if the Bootloader itself needs to be upgraded. In some cases AlphaCom features may also depend on the Bootloader version (such as hot stand-by mode). When the PC application connects to the AMC-IP it will read out the Bootloader version, and show in the status window if a bootloader upgrade is required or not. If required, run an Image Upgrade from the PC application.