Difference between revisions of "AudioCodes MP114/118, v4.8 and higher"
From Zenitel Wiki
(→AlphaCom Configuration) |
|||
| Line 18: | Line 18: | ||
* Create prefix numbers | * Create prefix numbers | ||
* Update the exchange | * Update the exchange | ||
| + | |||
| + | === AlphaWeb Configuration === | ||
| + | ==== Assign IP address to the AlphaCom E Ethernet port(s) ==== | ||
| + | Log on to AlphaWeb and enter a valid IP address on the Ethernet port. | ||
| + | In the example below, Ethernet port 1 is used. | ||
| + | Consult your network administrator to obtain the IP address. | ||
| + | |||
| + | [[image:Configuration guide for AudioCodes MP114 118 - Assign IP address to the AlphaCom E Ethernet.jpg|thumb|250px|]] | ||
| + | |||
| + | ==== Insert SIP Trunk licenses ==== | ||
| + | Log on to AlphaWeb and install the SIP Trunk license. | ||
| + | |||
| + | [[image:Configuration guide for AudioCodes MP114 118 - Insert SIP Trunk licenses.jpg|thumb|250px|]] | ||
| + | |||
| + | ==== Firewall (filter) settings ==== | ||
| + | Enable the SIP protocol on the desired Ethernet port | ||
| + | (default enabled for Ethernet port1). | ||
| + | |||
| + | [[image:Configuration guide for AudioCodes MP114 118 - Firewall (filter) settings.jpg|thumb|250px|]] | ||
| + | |||
| + | === AlphaPro Configuration === | ||
| + | ==== Create a SIP Trunk Node ==== | ||
| + | From the AlphaPro main menu, use the ‘+’ button next to the ‘Select | ||
| + | Exchange’ dropdown list to create a new exchange. | ||
| + | The exchange type must be set to ‘SIP Node’. | ||
| + | |||
| + | Set the parameters as follows: | ||
| + | |||
| + | [[image:Configuration guide for AudioCodes MP114 118 - Create a SIP Trunk Node.jpg|thumb|250px|]] | ||
| + | |||
| + | The SIP Trunk IP address must be identical to the IP address of the SIP | ||
| + | Gateway. | ||
| + | |||
| + | '''Note:''' If the AlphaCom is configured with a SIP Registar node in addition to the | ||
| + | SIP Trunk node, the SIP Registar node must have a lower node number | ||
| + | than the SIP Trunk node. | ||
| + | |||
| + | ==== Create AlphaCom/SIP Audion links === | ||
| + | ''This paragraph is only relevant for AMC software 10.04 or earlier.'' | ||
| + | |||
| + | From AMC 10.05 the audio links are assigned dynamically whenever | ||
| + | needed, and there is no need to specify the links in AlphaPro. Proceed | ||
| + | to paragraph 2.2.3. | ||
| + | |||
| + | However, if you want to reserve VoIP channels for the SIP Gateway, | ||
| + | you can do so by following the description below. | ||
| + | |||
| + | In '''Exchange & System > NetAudio''' use the ''Insert'' button to create one | ||
| + | or several audio (VoIP) links between the AlphaCom and the SIP | ||
| + | Gateway. | ||
| + | The physical number specifies the VoIP channel and must be in the | ||
| + | range 605 – 634 (start with 605). Normally the number of audio links will | ||
| + | be equal to the number of phone lines connected to the SIP Gateway. | ||
| + | |||
| + | [[image:Configuration guide for AudioCodes MP114 118 - Create AlphaCom/SIP Audio links.jpg|thumb|250px|]] | ||
| + | |||
| + | ==== Define the AlphaCom / SIP routing ==== | ||
Revision as of 09:22, 5 July 2007
Config guide SIP Gateway - AudioCodes MP114/118 here
Contents
AlphaCom Configuration
The configuration of AlphaCom E with SIP gateway includes the following steps:
Using AlphaWeb
- Assign IP address to the AlphaCom Ethernet port
- Insert SIP Trunk licenses
- Firewall (filter) settings
Using AlphaPro
- Create a SIP Trunk Node
- Create AlphaCom / SIP Audio links
- Define the AlphaCom / SIP routing
- Create prefix numbers
- Update the exchange
AlphaWeb Configuration
Assign IP address to the AlphaCom E Ethernet port(s)
Log on to AlphaWeb and enter a valid IP address on the Ethernet port. In the example below, Ethernet port 1 is used. Consult your network administrator to obtain the IP address.
Insert SIP Trunk licenses
Log on to AlphaWeb and install the SIP Trunk license.
Firewall (filter) settings
Enable the SIP protocol on the desired Ethernet port (default enabled for Ethernet port1).
_settings.jpg){kind=small}
AlphaPro Configuration
Create a SIP Trunk Node
From the AlphaPro main menu, use the ‘+’ button next to the ‘Select Exchange’ dropdown list to create a new exchange. The exchange type must be set to ‘SIP Node’.
Set the parameters as follows:
The SIP Trunk IP address must be identical to the IP address of the SIP Gateway.
Note: If the AlphaCom is configured with a SIP Registar node in addition to the SIP Trunk node, the SIP Registar node must have a lower node number than the SIP Trunk node.
= Create AlphaCom/SIP Audion links
This paragraph is only relevant for AMC software 10.04 or earlier.
From AMC 10.05 the audio links are assigned dynamically whenever needed, and there is no need to specify the links in AlphaPro. Proceed to paragraph 2.2.3.
However, if you want to reserve VoIP channels for the SIP Gateway, you can do so by following the description below.
In Exchange & System > NetAudio use the Insert button to create one or several audio (VoIP) links between the AlphaCom and the SIP Gateway. The physical number specifies the VoIP channel and must be in the range 605 – 634 (start with 605). Normally the number of audio links will be equal to the number of phone lines connected to the SIP Gateway.
