Difference between revisions of "TST console"
From Zenitel Wiki
(→from Linux console) |
(→Command Overview) |
||
Line 63: | Line 63: | ||
|" width="100pt"|0x0008 | |" width="100pt"|0x0008 | ||
|- | |- | ||
− | |bye|- Exit command | + | |bye||- Exit command |
|- | |- | ||
− | |nvram|- Edit NVRAM | + | |nvram||- Edit NVRAM |
|- | |- | ||
− | |busy|- list busy resources | + | |busy||- list busy resources |
|- | |- | ||
− | |err|- List Error Reports | + | |err||- List Error Reports |
|- | |- | ||
− | |rlogin|- Log on to TST on remote system | + | |rlogin||- Log on to TST on remote system |
|- | |- | ||
− | |rack|- List Boards / Hardware Resources of a board | + | |rack||- List Boards / Hardware Resources of a board |
|- | |- | ||
− | |xh|- Help text | + | |xh||- Help text |
|- | |- | ||
− | |dt|- (AlphaCom) Dataprotocol Trace mode | + | |dt||- (AlphaCom) Dataprotocol Trace mode |
|- | |- | ||
− | |sswrep|- (SSW) Report messages received | + | |sswrep||- (SSW) Report messages received |
|- | |- | ||
− | |globgrp|- list global group node memberships | + | |globgrp||- list global group node memberships |
|- | |- | ||
|} | |} |
Revision as of 13:58, 5 July 2007
Contents
General
- Part of the AlphaCom Software
- Debugging tool for software development
- Direct access to the AMC NVRAM memory
- Can be useful for troubleshooting
- TST Console uses a simple terminal interface
- - PC with terminal emulator (such as Hyper Terminal)
over IP
- TST Console via IP
- - Create a new connection in HyperTerminal
- - Host adress = IP-address of the AMC board
- - Port number must be 60001 (AlphaPro port)
- - When connecting you will be promped for username and password (admin + alphaadmin)
<br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\>
over Serial Port
- TST Console via serial port
- - Enable AlphaPro on Serial port 0: S601-1 ON
- - Connect the PC com port to AlphaCom serial port 0
- - Start Windows HyperTerminal
- PC serial port setting: 9600 baud, 8 data bits, no parity, 1 stop bit
<br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\>
Start and Stop
- TST Activation Code: #SERVICE* (no echo)
- - Response on VDU: TST-TARGET>>
- - New log-on required after reset
- Stop TST:
- - Type bye, or
- - Reset exchange
- - If not stopped properly, AlphaPro will not communicate
from Linux console
- TST Console can also be started from the Linux Console
- Simply type ”tst” on the Linux prompt...
<br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\>
- ...and the TST Console is activated:
<br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\><br\>
Command Overview
“xh” – Command Overview Some commands:
CALL_SETUP | 0x0008 | |
bye | - Exit command | |
nvram | - Edit NVRAM | |
busy | - list busy resources | |
err | - List Error Reports | |
rlogin | - Log on to TST on remote system | |
rack | - List Boards / Hardware Resources of a board | |
xh | - Help text | |
dt | - (AlphaCom) Dataprotocol Trace mode | |
sswrep | - (SSW) Report messages received | |
globgrp | - list global group node memberships |