SNMP in IP Stations
From Zenitel Wiki
Stentofon IP devices (INCA stations, Turbine stations, ENA Amplifiers) run a SNMP service and support SNMP polling and SNMP traps.
Stentofon OID numbers
Zenitel Norway AS has assigned a Private Enterprise Number OID 26122 and the IP-stations use sub OIDs 2,3 and 4.
All Zenitel OIDs definitions can be found in VS-DEVICE-MIB. MIB overview and all OID descriptions are also available at the end of this document.
In addtion to VS-DEVICE-MIB following built in MIBs are also available (not all available for INCA stations): SNMPv2-MIB, IF-MIB, IP-MIB, TCP-MIB, UDP-MIB, HOST-RESOURCES-MIB, NOTIFICATION-LOG-MIB, DISMAN-EVENT-MIB, DISMAN-SCHEDULE-MIB, UCD-SNMP-MIB, UCD-DEMO-MIB, SNMP-TARGET-MIB, NET-SNMP-AGENT-MIB, HOST-RESOURCES-TYPES, NET-SNMP-PASS-MIB, NET-SNMP-EXTEND-MIB, UCD-DLMOD-MIB, SNMP-MPD-MIB, SNMP-USER-BASED-SM-MIB, SNMP-FRAMEWORK-MIB, SNMP-VIEW-BASED-ACM-MIB, SNMP-COMMUNITY-MIB, IP-FORWARD-MIB, SNMP-NOTIFICATION-MIB, SNMPv2-TM, NET-SNMP-VACM-MIB
SNMP Configuration
SNMP can be configured from the station web (Advanced Network > SNMP).
For INCA stations, you need to set the station in SIP mode, enable SNMP, and set it back to AlphaCom mode. When INCA station operates in AlphaCom mode the SNMP service is still running, but only generic built in MIBs are supported.
For ENA Amplifiers and Turbine Stations, after upgrade from 4.9 or older SW to 4.10 or newer SW, SNMP configuration is retained, but when downgrading from 4.10 or newer SW to lower SW version than 4.10, SNMP needs to be reconfigured (factory reset recommended).
|
Not all fields are available on INCA stations |
SNMP Settings
- access: read or none are available, setting none will disable SNMP
- SNMP v1/v2c: selects SNMP version used, one or both need to be selected for SNMP to work
- Community string: string used as password for authentication
- Allowed network: this is used, together with the network mask, to determine the allowed network for reading the MIB on the station. The IP address is entered in regular dot notation, e.g. 10.5.2.100. For example with an allowed network 10.5.2.0 and a network mask of 24, any station with an IP address in the range 10.5.2.0 to 10.5.2.255 can access the MIB. Setting 0.0.0.0/0 will allow all
- Name: SNMP name string (sent as sysName OID in traps)
- Location SNMP Location string
- Contact: SNMP Contact string
SNMP Trap and Informs Settings
- Traps/informs receiving server address can be set here
- If left blank it will disable sending traps/informs
SNMP Custom Configuration File
- Custom snmpd.conf file can be uploaded and used on the device
- File is kept during device SW upgrades
- File syntax and content are not checked and if errors are present in the file it can render SNMP inoperative
- When custom file is uploaded SNMP Settings are unavailable
- File can be viewed or downloaded
- New file can be uploaded at any time
- When custom file is deleted device will revert back to configuration defined in web config
Enable SNMP Traps
- Available traps (notifications) depend on device type and mode
- If specific event occurs and corresponding SNMP Trap is enabled, notification (trap) will be generated and sent to trap/inform receiver IP address
- Traps description
Custom Faults
Custom faults are available only on amplifiers in SIP/Pulse or Exigo (configurable through EMT) mode. When RCI is triggered device will send SNMP Trap with custom fault description and priority.
Configuration for faults is available in web Amplifier Settings -> RCO/RCI Config (or IO Monitoring). For custom faults to be sent traps have to be enabled in config (Advanced Network → SNMP → Enable SNMP Traps → Custom Fault)
|
|
Available only on ENA amplifiers |
Object Identifier (OID) Numbers
Zenitel Norway AS OID is 26122 (stentofon) → 1.3.6.1.4.1.26122
Overview
| Name | OID |
|---|---|
| ipstation | 1.3.6.1.4.1.26122.2 |
| general | 1.3.6.1.4.1.26122.2.1 |
| registration | 1.3.6.1.4.1.26122.2.2 |
| call | 1.3.6.1.4.1.26122.2.3 |
| alarmObjects | 1.3.6.1.4.1.26122.2.4 |
| alarmNotifications | 1.3.6.1.4.1.26122.2.5 |
| faultNotifications | 1.3.6.1.4.1.26122.2.8 |
| vsDevice | 1.3.6.1.4.1.26122.3 |
| info | 1.3.6.1.4.1.26122.3.1 |
| temp | 1.3.6.1.4.1.26122.3.2 |
| fan | 1.3.6.1.4.1.26122.3.3 |
| voltage | 1.3.6.1.4.1.26122.3.4 |
| power | 1.3.6.1.4.1.26122.3.5 |
| lineIn | 1.3.6.1.4.1.26122.3.6 |
| ampChannel | 1.3.6.1.4.1.26122.3.7 |
| letStatus | 1.3.6.1.4.1.26122.3.8 |
| letChannel1 | 1.3.6.1.4.1.26122.3.8.1 |
| letChannel2 | 1.3.6.1.4.1.26122.3.8.2 |
| controlInput | 1.3.6.1.4.1.26122.3.9 |
| controlOutput | 1.3.6.1.4.1.26122.3.10 |
| eth | 1.3.6.1.4.1.26122.3.11 |
| relay | 1.3.6.1.4.1.26122.3.12 |
| stentofonMIBConformance | 1.3.6.1.4.1.26122.4 |
| stentofonMIBCompliances | 1.3.6.1.4.1.26122.4.1 |
| stentofonMIBGroups | 1.3.6.1.4.1.26122.4.2 |
ipstation scalar and tabular objects
| Name | OID | Syntax | Description |
|---|---|---|---|
| general | 1.3.6.1.4.1.26122.2.1 | ||
| softwareVersion | 1.3.6.1.4.1.26122.2.1.1 | DisplayString (SIZE (0..255)) | The software version |
| buttonHangingStatus | 1.3.6.1.4.1.26122.2.1.2 | Integer32 | Status of the inputs and DAK buttons, the returned number is bitmap where each bit represents hanging status of one input or DAK button in ascending order |
| buttonHangingCounter | 1.3.6.1.4.1.26122.2.1.3 | Counter32 | The number of input or buttons hanging since reboot |
| soundTestLastResult | 1.3.6.1.4.1.26122.2.1.4 | INTEGER { unused(0), error(1), failed(2), success(3) } | Last status of the sound test |
| soundTestFailedCounter | 1.3.6.1.4.1.26122.2.1.5 | Counter32 | The number of sound tests that failed since reboot |
| soundTestErrorCounter | 1.3.6.1.4.1.26122.2.1.6 | Counter32 | The number of attempts to automatically set the sound pressure level since reboot |
| soundTestSuccessCounter | 1.3.6.1.4.1.26122.2.1.7 | Counter32 | The number of sound tests that were successful since reboot |
| registration | 1.3.6.1.4.1.26122.2.2 | ||
| registrationTable | 1.3.6.1.4.1.26122.2.2.1 | SEQUENCE OF RegistrationEntry | Table of SIP registrations. |
| registrationEntry | 1.3.6.1.4.1.26122.2.2.1.1 | RegistrationEntry | SIP registration Entry |
| regIndex | 1.3.6.1.4.1.26122.2.2.1.1.1 | Unsigned32 | The SIP registration table index |
| serverType | 1.3.6.1.4.1.26122.2.2.1.1.2 | INTEGER { primary(0), backup(1), backup2(2) } | Priority of the SIP server |
| serverAddress | 1.3.6.1.4.1.26122.2.2.1.1.3 | DisplayString (SIZE (0..255)) | The address of the SIP server |
| isRegistered | 1.3.6.1.4.1.26122.2.2.1.1.4 | INTEGER { notregistered(0), registered(1) } | SIP registration state of the device towards this SIP server |
| lastRegistration | 1.3.6.1.4.1.26122.2.2.1.1.5 | DisplayString (SIZE (0..255)) | The time of the last successful registration with this SIP server |
| call | 1.3.6.1.4.1.26122.2.3 | ||
| callState | 1.3.6.1.4.1.26122.2.3.1 | INTEGER { idle(0), inprogress(1), incoming(2), outgoing(3), incancel(4) } | Call state of the device. |
| callRemoteId | 1.3.6.1.4.1.26122.2.3.2 | DisplayString (SIZE (0..255)) | The SIP-id of the remote party (empty unless device is in a call) |
| incomingCallAttempts | 1.3.6.1.4.1.26122.2.3.3 | Counter32 | The number of incoming call attempts since reboot |
| incomingCallsSuccess | 1.3.6.1.4.1.26122.2.3.4 | Counter32 | The number of successful incoming calls since reboot |
| incomingCallsFailed | 1.3.6.1.4.1.26122.2.3.5 | Counter32 | The number of incoming calls that has failed since reboot (unanswered calls are not considered failed) |
| outgoingCallAttempts | 1.3.6.1.4.1.26122.2.3.6 | Counter32 | The number of outgoing call attempts since reboot |
| outgoingCallsSuccess | 1.3.6.1.4.1.26122.2.3.7 | Counter32 | The number of successful outgoing calls since reboot |
| outgoingCallsFailed | 1.3.6.1.4.1.26122.2.3.8 | Counter32 | The number of outgoing calls that failed since reboot (unanswered calls are not considered failed) |
vsDevice scalar and tabular objects
| Name | OID | Syntax | Description |
|---|---|---|---|
| info | 1.3.6.1.4.1.26122.3.1 | ||
| infoPackageVersion | 1.3.6.1.4.1.26122.3.1.1 | DisplayString(SIZE(128)) | "The device Package Version |
| infoModelType | 1.3.6.1.4.1.26122.3.1.2 | DisplayString(SIZE(128)) | The device Model Type. |
| infoModelNumber | 1.3.6.1.4.1.26122.3.1.3 | Integer32 (0..9999) | The device Model Number. |
| infoAmplifierType | 1.3.6.1.4.1.26122.3.1.4 | DisplayString(SIZE(128)) | The device Amplifier Type (only for amplifier devices). |
| infoKernelVersion | 1.3.6.1.4.1.26122.3.1.5 | DisplayString(SIZE(128)) | The device Linux Kernel Version |
| infoDeviceTreeVersion | 1.3.6.1.4.1.26122.3.1.6 | DisplayString(SIZE(128)) | The device Device Tree Version. |
| infoDisablement | 1.3.6.1.4.1.26122.3.1.7 | INTEGER { offline(1), online(2) } | The device Disablement status. |
| temp | 1.3.6.1.4.1.26122.3.2 | ||
| tempTableCount | 1.3.6.1.4.1.26122.3.2.1 | Integer32 (0..5) | Number of Temperature entries in tempTable |
| tempTable | 1.3.6.1.4.1.26122.3.2.2 | SEQUENCE OF TempEntry | Table of temperature sensors and their values. |
| tempEntry | 1.3.6.1.4.1.26122.3.2.2.1 | TempEntry | An entry containing a device and its statistics. |
| tempIndex | 1.3.6.1.4.1.26122.3.2.2.1.1 | Integer32 (1..5) | Reference index for each temperature item |
| tempSensorName | 1.3.6.1.4.1.26122.3.2.2.1.2 | DisplayString(SIZE(128)) | The name of the temperature sensor we are reading. |
| tempCurrentString | 1.3.6.1.4.1.26122.3.2.2.1.3 | DisplayString(SIZE(128)) | The current temperature. |
| tempCurrentValue | 1.3.6.1.4.1.26122.3.2.2.1.4 | Gauge32 | The current temperature of this sensor in the device. |
| tempPeakString | 1.3.6.1.4.1.26122.3.2.2.1.5 | DisplayString(SIZE(128)) | The peak temperature. |
| tempPeakValue | 1.3.6.1.4.1.26122.3.2.2.1.6 | Gauge32 | The peak temperature of this sensor in the device. |
| tempAverageString | 1.3.6.1.4.1.26122.3.2.2.1.7 | DisplayString(SIZE(128)) | The average temperature. |
| tempAverageValue | 1.3.6.1.4.1.26122.3.2.2.1.8 | Gauge32 | The average temperature of this sensor in the device. |
| fan | 1.3.6.1.4.1.26122.3.3 | ||
| fanTableCount | 1.3.6.1.4.1.26122.3.3.1 | Integer32 (0..2) | Number of Fan entries in fanTable. |
| fanTable | 1.3.6.1.4.1.26122.3.3.2 | SEQUENCE OF FanEntry | Table of fans and their RPM status. |
| fanEntry | 1.3.6.1.4.1.26122.3.3.2.1 | FanEntry | An entry containing a device and its statistics. |
| fanIndex | 1.3.6.1.4.1.26122.3.3.2.1.1 | Integer32 (1..2) | Reference index for each observed device. |
| fanString | 1.3.6.1.4.1.26122.3.3.2.1.2 | DisplayString | The name of the fan sensor we are reading. |
| fanValue | 1.3.6.1.4.1.26122.3.3.2.1.3 | Gauge32 | The rotation speed of the fan in RPM. |
| voltage | 1.3.6.1.4.1.26122.3.4 | ||
| voltageTableCount | 1.3.6.1.4.1.26122.3.4.1 | Integer32 (0..20) | Number of Voltage entries in voltageTable. |
| voltageTable | 1.3.6.1.4.1.26122.3.4.2 | SEQUENCE OF VoltageEntry | Table of Voltage sensors and their values. |
| voltageEntry | 1.3.6.1.4.1.26122.3.4.2.1 | VoltageEntry | An entry containing a device and its Voltage statistics. |
| voltageIndex | 1.3.6.1.4.1.26122.3.4.2.1.1 | Integer32 (1..20) | Reference index for each observed device. |
| voltageString | 1.3.6.1.4.1.26122.3.4.2.1.2 | DisplayString(SIZE(128)) | The name of the device we are reading. |
| voltageValue | 1.3.6.1.4.1.26122.3.4.2.1.3 | Gauge32 | The voltage in mV. |
| power | 1.3.6.1.4.1.26122.3.5 | ||
| powerTable | 1.3.6.1.4.1.26122.3.5.1 | SEQUENCE OF PowerEntry | Table of Power sources and their status. |
| powerEntry | 1.3.6.1.4.1.26122.3.5.1.1 | PowerEntry | An entry containing Power source status. |
| powerIndex | 1.3.6.1.4.1.26122.3.5.1.1.1 | Integer32 (1..2) | Reference index for each observed Power source. |
| powerType | 1.3.6.1.4.1.26122.3.5.1.1.2 | INTEGER { unknown(1), acPower(2), dcPower(3), poePower(4) } | The type of the Power source we are reading. |
| powerString | 1.3.6.1.4.1.26122.3.5.1.1.3 | DisplayString(SIZE(128)) | The name of the Power source we are reading. |
| powerMonitoring | 1.3.6.1.4.1.26122.3.5.1.1.4 | INTEGER { unknown(1), notMonitored(2), monitored(3) } | The Monitoring state of the Power source. |
| powerStatus | 1.3.6.1.4.1.26122.3.5.1.1.5 | INTEGER { unknown(1), notConnected(2), connected(3) } | The Power source status. |
| lineIn | 1.3.6.1.4.1.26122.3.6 | ||
| lineInTable | 1.3.6.1.4.1.26122.3.6.1 | SEQUENCE OF LineInEntry | Table of Line In & Microphone and their status. |
| lineInEntry | 1.3.6.1.4.1.26122.3.6.1.1 | LineInEntry | An entry containing a device and its voltage statistics. |
| lineInIndex | 1.3.6.1.4.1.26122.3.6.1.1.1 | Integer32 (1..2) | Reference index for each Line In. |
| lineInMonitoringState | 1.3.6.1.4.1.26122.3.6.1.1.2 | INTEGER { unknown(1), notMonitored(2), monitored(3) } | The monitoring state of the Line In or Microphone. |
| lineInType | 1.3.6.1.4.1.26122.3.6.1.1.3 | INTEGER { unknown(1), lineIn1(2), lineIn2(3), microphoneExtern(4), microphoneIntern(5) } | The type of the Line In we are reading, either Line In or Microphone. |
| lineInString | 1.3.6.1.4.1.26122.3.6.1.1.4 | DisplayString(SIZE(128)) | The name of the Line In or Microphone we are reading. |
| lineInStatus | 1.3.6.1.4.1.26122.3.6.1.1.5 | INTEGER { unknown(1), lineInOk(2), lineInFail(3), microphoneUnknown(4), microphoneConnected(5), microphoneDisconnected(6), microphoneShorted(7) } | The Line In or Microphone status |
| ampChannel | 1.3.6.1.4.1.26122.3.7 | ||
| ampChannelCount | 1.3.6.1.4.1.26122.3.7.1 | Integer32 (0..2) | The total number of Amplifier channels. |
| ampType | 1.3.6.1.4.1.26122.3.7.2 | INTEGER { unknown(1), turbine(2), ena2200(3), ena2400(4), ena2060(5), ena2100(6) } | Type of Amplifier. |
| ampChannelTable | 1.3.6.1.4.1.26122.3.7.3 | SEQUENCE OF AmpChannelEntry | Table of Amplifier channels. |
| ampChannelEntry | 1.3.6.1.4.1.26122.3.7.3.1 | AmpChannelEntry | An entry containing a Amplifier channel. |
| ampChannelIndex | 1.3.6.1.4.1.26122.3.7.3.1.1 | Integer32 (1..2) | Index into Amplifier channel table. |
| ampChannelString | 1.3.6.1.4.1.26122.3.7.3.1.2 | DisplayString(SIZE(128)) | The name of the Amplifier channel. |
| ampChannelStatus | 1.3.6.1.4.1.26122.3.7.3.1.3 | INTEGER { unknown(1), notOperative(2), channelOk(3), channelFail(4), channelShutdown(5), channelGracefulDegradation(6) } | The Amplifier Channel status. |
| ampChannelMonitorStatus | 1.3.6.1.4.1.26122.3.7.3.1.4 | INTEGER { unknown(1), channelOk(2), channelShorted(3), channelOpen(4), channelLoadChange(5), channelGroundFault(6), channelRefreshing(7), channelShutdown(8), channelVoltageLow(9), channelIndecisive(10), channelInterrupted(11), channelTimeoutFail(12), channelMonitoringReceiveError(13), channelMonitoringSuspended(14), channelLineFault(15) } | The Amplifier Channel status. |
| letStatus | 1.3.6.1.4.1.26122.3.8 | ||
| letChannel1 | 1.3.6.1.4.1.26122.3.8.1 | ||
| letChannel1Count | 1.3.6.1.4.1.26122.3.8.1.1 | Integer32 (0..10) | The total number of configuration enabled LETs in channel 1. |
| letChannel1Table | 1.3.6.1.4.1.26122.3.8.1.2 | SEQUENCE OF LetChannel1Entry | Table of LETs and their status. |
| letChannel1Entry | 1.3.6.1.4.1.26122.3.8.1.2.1 | LetChannel1Entry | An entry containing a LET and status. |
| letChannel1Index | 1.3.6.1.4.1.26122.3.8.1.2.1.1 | Integer32 (1..10) | The index into this selection of LET data. |
| letChannel1Description | 1.3.6.1.4.1.26122.3.8.1.2.1.2 | DisplayString(SIZE(128)) | Descriptive text about the LET we are reading. |
| letChannel1OperativeStatus | 1.3.6.1.4.1.26122.3.8.1.2.1.3 | INTEGER { unknown(1), notEnabled(2), failed(3), ok(4) } | The LET status. |
| letChannel1SoftwareVersion | 1.3.6.1.4.1.26122.3.8.1.2.1.4 | DisplayString(SIZE(20)) | Software Version of the LET. |
| letChannel1HardwareVersion | 1.3.6.1.4.1.26122.3.8.1.2.1.5 | DisplayString(SIZE(20)) | Hardware Version of the LET. |
| letChannel1Voltage | 1.3.6.1.4.1.26122.3.8.1.2.1.6 | Gauge32 (0..39999) | Voltage in mV at LET. |
| letChannel2 | 1.3.6.1.4.1.26122.3.8.2 | ||
| letChannel2Count | 1.3.6.1.4.1.26122.3.8.2.1 | Integer32 (0..10) | The total number of configuration enabled LETs in channel 2 |
| letChannel2Table | 1.3.6.1.4.1.26122.3.8.2.2 | SEQUENCE OF LetChannel1Entry | Table of LETs and their status. |
| letChannel2Entry | 1.3.6.1.4.1.26122.3.8.2.2.1 | LetChannel1Entry | An entry containing a LET and status. |
| letChannel2Index | 1.3.6.1.4.1.26122.3.8.2.2.1.1 | Integer32 (1..10) | The index into this selection of LET data. |
| letChannel2Description | 1.3.6.1.4.1.26122.3.8.2.2.1.2 | DisplayString(SIZE(128)) | Descriptive text about the LET we are reading. |
| letChannel2OperativeStatus | 1.3.6.1.4.1.26122.3.8.2.2.1.3 | INTEGER { unknown(1), notEnabled(2), failed(3), ok(4) } | The LET status. |
| letChannel2SoftwareVersion | 1.3.6.1.4.1.26122.3.8.2.2.1.4 | DisplayString(SIZE(20)) | Software Version of the LET. |
| letChannel2HardwareVersion | 1.3.6.1.4.1.26122.3.8.2.2.1.5 | DisplayString(SIZE(20)) | Hardware Version of the LET. |
| letChannel2Voltage | 1.3.6.1.4.1.26122.3.8.2.2.1.6 | Gauge32 (0..39999) | Voltage in mV at LET. |
| controlInput | 1.3.6.1.4.1.26122.3.9 | ||
| controlInputCount | 1.3.6.1.4.1.26122.3.9.1 | Integer32 (1..6) | Number of Control Input entries in controlInputTable. |
| controlInputTable | 1.3.6.1.4.1.26122.3.9.2 | SEQUENCE OF ControlInputEntry | Table of Control Input sensors and their values. |
| controlInputEntry | 1.3.6.1.4.1.26122.3.9.2.1 | ControlInputEntry | An entry containing a Control Input and its status. |
| controlInputIndex | 1.3.6.1.4.1.26122.3.9.2.1.1 | Integer32 (1..6) | Reference index for each Control Input. |
| controlInputString | 1.3.6.1.4.1.26122.3.9.2.1.2 | DisplayString(SIZE(128)) | The name of the Control Input. |
| controlInputStatus | 1.3.6.1.4.1.26122.3.9.2.1.3 | INTEGER { unknown(1), open(2), closed(3), failShorted(4), failOpen(5) } | The Control Input status. |
| controlInputMonitored | 1.3.6.1.4.1.26122.3.9.2.1.4 | INTEGER { notMonitored(1), monitored(2) } | The Control Input Monitored status. |
| controlOutput | 1.3.6.1.4.1.26122.3.10 | ||
| controlOutputCount | 1.3.6.1.4.1.26122.3.10.1 | Integer32 (1..6) | Number of Control Output entries in controlOutputTable. |
| controlOutputTable | 1.3.6.1.4.1.26122.3.10.2 | SEQUENCE OF ControlOutputEntry | Table of Control Output sensors and their values. |
| controlOutputEntry | 1.3.6.1.4.1.26122.3.10.2.1 | ControlOutputEntry | An entry containing a Control Output and its status. |
| controlOutputIndex | 1.3.6.1.4.1.26122.3.10.2.1.1 | Integer32 (1..6) | Reference index for each Control Output. |
| controlOutputString | 1.3.6.1.4.1.26122.3.10.2.1.2 | DisplayString(SIZE(128)) | The name of the Control Output. |
| controlOutputStatus | 1.3.6.1.4.1.26122.3.10.2.1.3 | INTEGER { unknown(1), notActive(2), active(3), failNotActive(4), failActive(5) } | The Control Output status. |
| eth | 1.3.6.1.4.1.26122.3.11 | ||
| ethMonitoringTable | 1.3.6.1.4.1.26122.3.11.1 | SEQUENCE OF EthMonitoringEntry | Table of Eth Switch Monitoring state. |
| ethMonitoringEntry | 1.3.6.1.4.1.26122.3.11.1.1 | EthMonitoringEntry | An entry containing an Eth Switch and its Monitoring state. |
| ethMonitoringIndex | 1.3.6.1.4.1.26122.3.11.1.1.1 | Integer32 (1..2) | Reference index for each Eth Switch Monitored. |
| ethMonitoringString | 1.3.6.1.4.1.26122.3.11.1.1.2 | DisplayString(SIZE(128)) | The name of the monitored Eth Switch. |
| ethMonitoringState | 1.3.6.1.4.1.26122.3.11.1.1.3 | INTEGER { unknown(1), notMonitored(2), monitored(3) } | The Eth Switch Monitoring state. |
| relay | 1.3.6.1.4.1.26122.3.12 | ||
| relayTable | 1.3.6.1.4.1.26122.3.12.1 | SEQUENCE OF RelayEntry | Table of Relay state. |
| relayEntry | 1.3.6.1.4.1.26122.3.12.1.1 | RelayEntry | An entry containing a Relay and its state. |
| relayIndex | 1.3.6.1.4.1.26122.3.12.1.1.1 | Integer32 (1..4) | Reference index for each Relay monitored. |
| relayString | 1.3.6.1.4.1.26122.3.12.1.1.2 | DisplayString(SIZE(128)) | The name of the monitored Relay. |
| relayIdleMode | 1.3.6.1.4.1.26122.3.12.1.1.3 | INTEGER { unknown(1), normallyClosed(2), normallyOpen(3) } | Relay idle mode state. |
| relayDelay | 1.3.6.1.4.1.26122.3.12.1.1.4 | Integer32 (0..30) | Delay time (sec) before activation. |
| relayState | 1.3.6.1.4.1.26122.3.12.1.1.5 | INTEGER { unknown(1), notActive(2), active(3) } | Relay state. |
Notifications (traps)
Alarm Objects
Each notification (trap) contains Alarm object with following fields
| Name | OID | Syntax | Description |
|---|---|---|---|
| alarmObjects | 1.3.6.1.4.1.26122.2.4 | ||
| managedObjectClass | 1.3.6.1.4.1.26122.2.4.1 | DisplayString (SIZE (0..255)) | This object identifies the class of network to which the subject alarm is related: Stentofon IPStation |
| managedObjectInstance | 1.3.6.1.4.1.26122.2.4.2 | DisplayString (SIZE (0..255)) | This object identifies the instance (of a class) of network resource to which the subject alarm is related: device hostname |
| severity | 1.3.6.1.4.1.26122.2.4.3 | INTEGER { indeterminate(0), critical(1), major(2), minor(3), warning(4), info(5), cleared(6) } | The severity of the alarm according to X.733. |
| time | 1.3.6.1.4.1.26122.2.4.4 | DisplayString (SIZE(0..255)) | The timestamp of the alarm as a string: 'Week day MM DD HH.mm.ss YYYY' eg. Tue Jan 15 19.34.57 2019 |
| description | 1.3.6.1.4.1.26122.2.4.5 | DisplayString (SIZE(0..255)) | Specific problem description. |
| sysname | 1.3.6.1.2.1.1.5 | DisplayString (SIZE(0..255)) | An administratively-assigned name for this device. NOTE: Not sent when custom snmpd.conf file is used |
Alarm/Fault Notifications (Traps)
Availability dependent on device mode (Sip, Pulse, Alphacom...) and device type and model
| Name | OID | Description |
|---|---|---|
| alarmNotifications | 1.3.6.1.4.1.26122.2.5 | NOTE: Available only in SIP/Pulse mode |
| ipsStarted | 1.3.6.1.4.1.26122.2.5.1 | Device has started. |
| sipRegistered | 1.3.6.1.4.1.26122.2.5.3 | Device has successfully registered with a SIP server |
| sipRegisterFailed | 1.3.6.1.4.1.26122.2.5.5 | Device failed to register with a SIP server |
| callConnect | 1.3.6.1.4.1.26122.2.5.6 | Call has connected successfully |
| callConnectFailed | 1.3.6.1.4.1.26122.2.5.7 | Call has failed to connect |
| callDisconnect | 1.3.6.1.4.1.26122.2.5.8 | Call has disconnected |
| soundTestSuccess | 1.3.6.1.4.1.26122.2.5.10 | Sound test was successful |
| soundTestFailed | 1.3.6.1.4.1.26122.2.5.11 | Sound test has failed |
| soundTestError | 1.3.6.1.4.1.26122.2.5.12 | Automatically setting sound pressure level failed |
| buttonHanging | 1.3.6.1.4.1.26122.2.5.13 | Button was pushed for more than 10 seconds without being released |
| buttonPressed | 1.3.6.1.4.1.26122.2.5.14 | Input button was pressed. Trap description will provide more info about input number |
| buttonReleased | 1.3.6.1.4.1.26122.2.5.15 | Input button was released. Trap description will provide more info about input number |
| relayActivated | 1.3.6.1.4.1.26122.2.5.16 | Relay was activated. Trap description will provide more info about relay number |
| relayDeactivated | 1.3.6.1.4.1.26122.2.5.17 | Relay was deactivated. Trap description will provide more info about relay number |
| dakPressed | 1.3.6.1.4.1.26122.2.5.18 | DAK was pressed. Trap description will provide more info about DAK number |
| dakReleased | 1.3.6.1.4.1.26122.2.5.19 | DAK was released. Trap description will provide more info about DAK number |
| faultNotifications | 1.3.6.1.4.1.26122.2.8 | NOTE: Available depending on device type and model, eg. amplifier, kit, device has ETH switch... |
| coolingFanFault | 1.3.6.1.4.1.26122.2.8.1 | There is a cooling fan fault eg. low speed, not running. Trap description will provide RPM and fan details |
| missingAmpModule | 1.3.6.1.4.1.26122.2.8.2 | Amplifier module is missing |
| psuVoltageFault | 1.3.6.1.4.1.26122.2.8.3 | Power supply voltage is not within operational range. Trap description will provide more information about voltage values |
| lineVoltageFault | 1.3.6.1.4.1.26122.2.8.4 | Selected speaker line voltage is not applied. |
| letFault | 1.3.6.1.4.1.26122.2.8.5 | Reported only if Line End Transponder (LET) monitoring enabled and configured. LET has failed. Trap description will provide let channel and number |
| ampShutdown | 1.3.6.1.4.1.26122.2.8.6 | Amplifier audio channel is shut down. Trap description will provide details about affected channel |
| slmFault | 1.3.6.1.4.1.26122.2.8.7 | Speaker Line Monitoring (SLM) related fault has occurred. Trap description will provide fault details and affected channel |
| fuseBroken | 1.3.6.1.4.1.26122.2.8.8 | Fuse is broken. Trap description will provide information about affected fuse |
| ampDisabled | 1.3.6.1.4.1.26122.2.8.9 | Amplifier audio channel is disabled. Trap description will provide details about affected channel |
| lineInFault | 1.3.6.1.4.1.26122.2.8.10 | Reported only if Line In monitoring enabled. Line in is disconnected |
| rcoFault | 1.3.6.1.4.1.26122.2.8.11 | Reported only if RCO monitoring enabled. Control output is not set or cleared. Trap description will provide more info about affected output and fault details |
| rciFault | 1.3.6.1.4.1.26122.2.8.12 | Reported only if RCI monitoring enabled. Control input shorted or not connected. Trap description will provide more info about affected input and fault details |
| dcPowerFault | 1.3.6.1.4.1.26122.2.8.13 | Reported only if DC Power monitoring enabled. AC power disconnected |
| acPowerFault | 1.3.6.1.4.1.26122.2.8.14 | Reported only if AC Power monitoring enabled. AC power disconnected |
| ethPortDisconnected | 1.3.6.1.4.1.26122.2.8.15 | Reported only if ETH port monitoring enabled. Ethernet port is disconnected. Trap description will provide more info about affected port number |
| micFault | 1.3.6.1.4.1.26122.2.8.16 | Reported only if mic monitoring is enabled. Microphone is not connected or shorted. Trap description will provide fault details |
| missingEmbdr | 1.3.6.1.4.1.26122.2.8.17 | Panel device is missing EMBDR expansion modules |
| swFault | 1.3.6.1.4.1.26122.2.8.18 | Software daemon has stopped working. Trap description will provide more info about affected daemon |
| tempFault | 1.3.6.1.4.1.26122.2.8.19 | High temperature is detected. Trap description will provide more info about value and affected sensor. |
| customFault | 1.3.6.1.4.1.26122.2.8.20 | Report External Custom Faults. Trap description will provide more info about fault |
Compliance and groups
Compliance
| Name | OID | Content |
|---|---|---|
| stentofonMIBCompliances | 1.3.6.1.4.1.26122.4.1 | |
| Mandatory Groups | alarmObjectsGroup
sipNotificationsGroup faultNotificationsGroup deviceInfoGroup sipGeneralGroup | |
| Optional Groups | sipRegistrationGroup
sipCallGroup deviceStatusGroup audioInputsGroup controlIOGroup ethernetGroup amplifierGroup letsGroup |
Groups
| Name | OID | Content | Description |
|---|---|---|---|
| stentofonMIBGroups | 1.3.6.1.4.1.26122.4.2 | ||
| sipRegistrationGroup | 1.3.6.1.4.1.26122.4.2.1 | serverType
serverAddress isRegistered lastRegistration |
A collection of registration related objects, available only when device is in SIP/Pulse mode" |
| sipCallGroup | 1.3.6.1.4.1.26122.4.2.2 | callState
callRemoteId incomingCallAttempts incomingCallsSuccess incomingCallsFailed outgoingCallAttempts outgoingCallsSuccess outgoingCallsFailed |
A collection of call state related objects, available only when device is in SIP/Pulse mode |
| sipGeneralGroup | 1.3.6.1.4.1.26122.4.2.3 | softwareVersion
buttonHangingStatus buttonHangingCounter soundTestLastResult soundTestFailedCounter soundTestErrorCounter soundTestSuccessCounter |
A collection of general device info objects available only when device is in SIP/Pulse mode |
| alarmObjectsGroup | 1.3.6.1.4.1.26122.4.2.4 | managedObjectClass
managedObjectInstance severity time description |
A collection of objects included in all notifications |
| sipNotificationsGroup | 1.3.6.1.4.1.26122.4.2.5 | ipsStarted
ipsShutdown sipRegistered sipUnregistered sipRegisterFailed callConnect callConnectFailed callDisconnect callAbnormalDisconnect soundTestSuccess soundTestFailed soundTestError buttonHanging buttonPressed buttonReleased relayActivated relayDeactivated dakPressed dakReleased |
A collection of notifications available only when device is in SIP/Pulse mode and dependent on device type and model |
| faultNotificationsGroup | 1.3.6.1.4.1.26122.4.2.6 | coolingFanFault
missingAmpModule psuVoltageFault lineVoltageFault letFault ampShutdown slmFault fuseBroken ampDisabled lineInFault rcoFault rciFault dcPowerFault acPowerFault ethPortDisconnected micFault missingEmbdr swFault tempFault customFault |
A collection of fault monitoring related notifications, availability based on device type and model |
| deviceInfoGroup | 1.3.6.1.4.1.26122.4.2.7 | infoPackageVersion
infoModelType infoModelNumber infoAmplifierType infoKernelVersion infoDeviceTreeVersion infoDisablement |
A collection of device info objects, some fields not available on all device types |
| deviceStatusGroup | 1.3.6.1.4.1.26122.4.2.8 | tempTableCount
tempSensorName tempCurrentString tempCurrentValue tempPeakString tempPeakValue tempAverageString tempAverageValue fanTableCount fanString fanValue voltageTableCount voltageString voltageValue powerType powerString powerMonitoring powerStatus |
A collection of device temperature, fan speed, internal voltages and power status objects, available on amplifier devices |
| audioInputsGroup | 1.3.6.1.4.1.26122.4.2.9 | lineInMonitoringState
lineInType lineInString lineInStatus |
A collection of audio inputs device objects, available only on devices with microphone or line in monitoring |
| controlIOGroup | 1.3.6.1.4.1.26122.4.2.10 | controlInputCount
controlInputString controlInputStatus controlInputMonitored controlOutputCount controlOutputString controlOutputStatus relayString relayIdleMode relayDelay relayState |
A collection of control input and control output (CIO) device objects, available only on devices with CIO monitoring |
| ethernetGroup | 1.3.6.1.4.1.26122.4.2.11 | ethMonitoringString
ethMonitoringState |
A collection of Ethernet switch monitoring objects, available on devices with Ethernet switch |
| amplifierGroup | 1.3.6.1.4.1.26122.4.2.12 | ampChannelCount
ampType ampChannelString ampChannelStatus ampChannelMonitorStatus |
A collection of amplifier info objects |
| letsGroup | 1.3.6.1.4.1.26122.4.2.13 | letChannel1Count
letChannel1Description letChannel1OperativeStatus letChannel1SoftwareVersion letChannel1HardwareVersion letChannel1Voltage letChannel2Count letChannel2Description letChannel2OperativeStatus letChannel2SoftwareVersion letChannel2HardwareVersion letChannel2Voltage |
A collection of line end transponder (LET) objects, available only on devices that support LET connections |