AlphaPro Release Notes

Software in production: AlphaPro 10.24<br\> Software released date: 2007-04-12<br\> NOTE: AlphaPro requires Windows 2000 or XP to run.<br\><br\>

AlphaPro Versions

<br\>

AlphaPro 10.25 (2007-06-15)

Run InstallAlphaPro.exe from the installation set. 
The installation can be used as an upgrade of v10.0.1 of AlphaPro (installed on top of old version).

Functional changes

---

Automatic reconnect: By right-clicking on the communication button in AlphaPro, there will be a menu with two options: Logout and Automatic reconnect. The Logout option will be disabled if not logged in yet. The Automatic reconnect function has an on/off state that is visualized with a check-mark to the left of the menu option. When turned on and the TCP connection to the AMC is broken, AlphaPro will try to reconnect and log in to the node again.<br\><br\>

New fields: In Exchange|System:<br\> .ex_profile.glob_const.priv_ring_mail_pri<br\> .ex_profile.glob_const.bc_event_node<br\> .ex_profile.glob_const.max_off_hook_delay<br\> .ex_profile.timeouts.dig_col_timeout<br\> .ex_profile.timeouts.sip_dial_dly<br\> .ex_profile.flags.use_IP_ICC<br\> .ex_profile.flags.DSP_duplex<br\> .ex_profile.flags.private_ringing_SIP<br\> .ex_profile.flags.prog_feed_in_master<br\> .ex_profile.ip_config.mcast_addr_base<br\> .ex_profile.ip_config.mcast_net_rly[5].net_addr<br\> .ex_profile.ip_config.mcast_net_rly[5].net_mask<br\><br\>

Errors corrected

---

3192: Hebrew problem on station display:<br\> Correction in wacs to handle 4 byte boolean variable in AMC 10.<br\>

3190: Event action - radio button:<br\> When you add a new event from the Users & Stations window, neither of the two radio buttons for Action Command or RCO is activated. So when you enter your actions strings and press OK the action commands are not saved. When entering Events from Exchange & System it is OK. Corrected.<br\>

2839: RCI - Faults:<br\> Programmed information on RCI 140 (amongst other programming) + SendChg. Then GetAll. In the RCI | Faults window the programming of RCI 140 appears in the disabled fields (OFF action, Device number, Pin number, Delay) of the Faulty station/board/device/AGA. Corrected.<br\>

3194: SIP Registrar on eth1 not OK:<br\> Using SIP Registrar on eth1 would not work. Corrected.<br\>

3199: Inser new event, subevent:<br\> When inserting a new event the subevent field must be cleared (set to 0). When inserting a new event the same subevent number as from the last highlighted event is used. If this subevent was different from 0 the new event might not work. Corrected<br\>

3200: Event - Edit action command:<br\> When editing the action command of an existing event, the button OK and Cancel doesn't become active. You must place the cursor in another field first. Corrected.<br\>

3189: Event is changed when owner is:<br\> When owner is changed in event handler from station to UDP or visa versa the event part is reset. That is event type will be 01 - Audio, when change to will be ON or OFF and any related to information is deleted. Corrected.<br\>

3186: Transfer configuration to AMC:<br\> Speed improvement when transferring data to AMC (SendChg).<br\>

3207: Convertion of AMC9 databases:<br\> A database from 9.23 is converted in 10.25. Then I set the node type to be AlphaCom E. The IP address is not saved after pressing OK. Corrected.<br\>

3212: AlphaPro can't start after del network:<br\> Corrected.<br\>

3204: Deleting the only node -> AP closes:<br\> AlphaPro closes when deleting the one and only node in a network. Corrected.<br\>

3222: Crash when defining groups:<br\> When adding many stations (>100) into groups, AlphaPro will eventually crash. Corrected.<br\>

3221: AlphaPro can't get/set IP address:<br\> After a GetAll the IP address is 0.0.0.0 on all nodes except the connected node it self. All remote nodes and SIP nodes have IP 0.0.0.0. When trying to edit an IP address, the information is not stored. Corrected.<br\>

2859: Wacs not restored:<br\> Corrected by implementing the 'Automatic reconnect' function (see Automatic reconnect).<br\>

Unregistered bugfixes:<br\> New text for event trigger 31 and 32:<br\> Event 31: FEAT_M_KEY<br\> Event 32: FEAT_OFF_HOOK<br\><br\>

Updated MDF files:<br\> Related to Issue 2952 (AMC, dual display) a new line is added to the default MDF files:<br\>

#UMSG 10 14  % H_SDMSG_SEL_MAIL
% Parameter: 1 - Dir.no. dialled
"Dial Mail#clr"
" message: $dno:1#clr"
"#pos(6,1)#clr"   <-- New line
(12,1)

Known bugs/workarounds:<br\> None as of now.