Actions

Difference between revisions of "AlphaCom XE26"

From Zenitel Wiki

 
(30 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
[[Image:XE26.PNG|thumb|250px|AlphaCom XE26 Audio Server with HD Voice]]
 
[[Image:XE26.PNG|thumb|250px|AlphaCom XE26 Audio Server with HD Voice]]
  
===<u>Highlights</u>===
+
=Highlights=
 
* Made to provide critical communication in any environment
 
* Made to provide critical communication in any environment
 
* Supports 552 IP stations and 138 analog intercom stations
 
* Supports 552 IP stations and 138 analog intercom stations
Line 7: Line 7:
 
* Fully compatible with any AlphaCom system
 
* Fully compatible with any AlphaCom system
  
===<u>[http://www.zenitel.com/product/alphacom-xe26 Additional Documentation on Zenitel.com]</u>===
+
=Variants=
 +
There are three standard cabinet models: 19” rack mounting, floor cabinet, and floor cabinet with distribution field:
 +
[[Image:XE26 installation.PNG|Mounting AlphaCom XE26|thumb|left|500px]]
 +
<br style="clear:both;" />
 +
 
 +
=Mounting & Dimensions=
 +
The cabinet has room for installation of 26 circuit boards in total: one AMC-IP processor board, one APC program & clock board, and up to 24 feature boards. The server also includes a mains power supply and a cooling fan.
  
===<u>Variants</u>===
+
[[File:XE26FrontView.PNG|300px|left|thumb|Front View]]
[[Image:XE26 installation.PNG|Mounting AlphaCom XE26|thumb|left|500px]]
+
<br style="clear:both;" />
 +
[[File:XE26RearView.PNG|300px|left|thumb|Rear View]]
 +
<br style="clear:both;" />
 +
[[File:XE26TopView.png|300px|left|thumb|Top View]]
 +
<br style="clear:both;" />
 +
[[File:XE26SideView.PNG|300px|left|thumb|Side View]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
===<u>Board positions</u>===
+
=Board positions=
[[Image:XE20 backplane2.png|thumb|500px|left|Board positions and physical numbers in AlphaCom XE20]]
+
[[Image:XE26 backplane2.png|thumb|500px|left|Board positions and physical numbers in AlphaCom XE20 seen from the rear]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
===<u>Connections</u>===
+
=Connections=
 
[[File:XE26 Connections.PNG|thumb|left|500px]]
 
[[File:XE26 Connections.PNG|thumb|left|500px]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
* The exchange is powered from the mains.
 
* The two-pair star wired intercom cables are connected to connection boards or a separate distribution field
 
* Each [[ASLT|subscriber line card]] provides 6 freely programmable Remote Control Outputs ([[RCO]])
 
* Two RJ-45 Ethernet terminals on the [[Filter card AMC-IP|IP filter board]] are used for IP LAN and WAN communication
 
* 6 [[Audio Program|program distribution]] sources can be connected to the [[APC - AlphaCom Program & Clock Board|APC board]] via an optional program connection board. Up to 64 extra programs may be added using AGA boards with 16 programs per board
 
* The [[Filter card APC|optional program connection]] board has input for 6 Remote Control Inputs ([[RCI]]) which can initiate programmed actions
 
* The serial ports with RS232 and RS422/RS485 interfaces are used for connecting to equipment using these protocols. Eth0 is also used for programming
 
  
====Serial Ports====
+
===Power===
Serial Port 0 - RJ45 (RS232 Only)
+
The exchange is powered from the mains.
 +
 
 +
===Network===
 +
Two RJ-45 Ethernet terminals on the [[Filter card AMC-IP|IP filter board]] are used for IP LAN and WAN communication
 +
 
 +
===Analogue Intercom Stations===
 +
The two-pair star wired intercom cables are connected to connection boards on the cabinet DIN rail or in a separate distribution field
 +
 
 +
===Program Input===
 +
6 [[Audio Program|program distribution]] sources can be connected to the [[APC - AlphaCom Program & Clock Board|APC board]] via an optional program connection board. Up to 64 extra programs may be added using AGA boards with 16 programs per board
 +
 
 +
===Serial Ports===
 +
The serial ports with RS232 and RS422/RS485 interfaces are used for connecting to equipment using these protocols
 +
 
 +
[[Image:AMC-IP-Connections.PNG|thumb|left|400px]]
 +
<br style="clear:both;" />
 +
 
 +
====Serial Port 0====
 +
RJ45 (RS232 Only)
 
:No additional settings necessary
 
:No additional settings necessary
  
----
+
====Serial Port 1====
 
+
RJ45 (RS232/422/485)
Serial Port 1 - RJ45 (RS232/422/485)
 
 
:Additional settings:
 
:Additional settings:
 
:'''RS232:'''
 
:'''RS232:'''
 
:* [[AMC-IP_-_AlphaCom_Processor_Board_(Red)#Switches_and_jumpers|Switch 8 on S601]] on the AMC-IP board must be set to OFF.
 
:* [[AMC-IP_-_AlphaCom_Processor_Board_(Red)#Switches_and_jumpers|Switch 8 on S601]] on the AMC-IP board must be set to OFF.
  
:'''RS422:'''
+
:'''RS422/485:'''
 
:* [[AMC-IP_-_AlphaCom_Processor_Board_(Red)#Switches_and_jumpers|Switch 8 on S601]] on the AMC-IP board must be set to ON.
 
:* [[AMC-IP_-_AlphaCom_Processor_Board_(Red)#Switches_and_jumpers|Switch 8 on S601]] on the AMC-IP board must be set to ON.
:* Set the two jumpers on the AMC-IP [[Filter card AMC-IP|Filterboard]] to the correct position.
+
:* Use the two jumpers on the AMC-IP [[Filter card AMC-IP|Filterboard]] to select between RS422 and RS485.
 
[[File:SerialPortJumpers XE20 26.png|thumb|left|500px|RS422/485 selector for Serial Port 1 on the XE26 AMC-IP Filterboard]]
 
[[File:SerialPortJumpers XE20 26.png|thumb|left|500px|RS422/485 selector for Serial Port 1 on the XE26 AMC-IP Filterboard]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
 +
===Remote Control Inputs (RCI)===
 +
====Connections====
 +
The [[Filter card APC|optional program connection]] board has input for 6 Remote Control Inputs ([[RCI]]) which can initiate programmed actions
 +
 +
[[File:RCI XE26.png|left|thumb|500px|right|RCI inputs in an AlphaCom XE20 and XE26]]
 +
<br style="clear:both;" />
 +
 +
====Configuration====
 +
In [[AlphaPro]] there is an [[Exchange_%26_System_%28AlphaPro%29#RCI|RCI table]], where the physical address of the input is entered, along with the desired actions. The physical address is given as [[device]] + pin-number.
 +
 +
The RCI table supports up to 140 inputs.
 +
* For internal RCIs in the AlphaCom XE1, the device address is 68, and the pin number is 1-6.
 +
* Internal pin number 8 is the [[Temperature Alarm|temperature alarm]]
 +
* Mappings for the internal RCI's are [[Autoload|autoloaded]]. Mappings for external RCI's (Slave modules, RIO's or IPARIO) must be manually programmed.
 +
 +
{| border="1"
 +
! style="background:#ffdead;" width="150" |&nbsp;
 +
! style="background:#ffdead;" width="80" |RCI Type
 +
! style="background:#ffdead;" width="150" |Device/Station physical Number
 +
! style="background:#ffdead;" width="100" |Pin Number
 +
|-
 +
| align=center | AlphaCom XE26 || align=center | Device || align=center | 65-68 || align=center | 1 - 6
 +
|-
 +
|}
 +
 +
====Example====
 +
<big>Start fire alarm message and activate rotating lamp:</big>
 +
[[File:RCI Conf Example1.PNG|left|800px]]
 +
<br style="clear:both;" />
 +
 +
[[File:RCI Conf Example2.PNG|left|500px]]
 +
<br style="clear:both;" />
 +
 +
AMG 1 3 - Alarm Message 3 (8193) to group 1 (84)
 +
RCO 5 ON – Turn on the relay that controls the lamp
 +
 +
AMG 1 0 – Alarm Message OFF to group 1 (84)
 +
RCO 5 OFF – Turn off the lamp
 +
 +
'''Note:''' Multiple commands are separated by semicolon ( ; )
 +
 +
===Remote Control Outputs (RCO)===
 +
Each [[ASLT|subscriber line card]] provides 6 freely programmable Remote Control Outputs ([[RCO]])
 +
 +
{| border="1"
 +
! style="background:#ffdead;" width="250" |Device
 +
! style="background:#ffdead;" width="50" |# of RCO's
 +
! style="background:#ffdead;" width="300" |Comment
 +
! style="background:#ffdead;" width="400" |Hardware required
 +
|-
 +
| align=center | AlphaCom XE26]] || align=center | 138|| align=center | 6 RCOs per [[ASLT]] card or [[ATLB-12]] card || align=center | [[MRBD - Relay Board|MRBD relay board]] + [[Power Distribution Board|PDB Power Distribution Board]]
 +
|-
 +
|}
 +
 +
=Factory Reset (coldstart)=
 +
Performing a '''cold start''' of the AMC-IP board will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0.
 +
 +
[[File:AMC-IP ColdStartButton2.png|thumb|left|100px|Cold start button on AMC-IP board]]
 +
<br style="clear:both;" />
 +
 +
===Cold start procedure===
 +
[[Image:Cold Start of AMC-IP.jpg|right|200px|thumb|Cold start to load default factory settings]]
 +
*Press the reset button on the [[APC|APC board]] briefly while keeping the cold start button pressed.
 +
*Keep the cold start button pressed at least 2 sec. after power on. The AMC status LED will blink green when the boot is ready.
 +
<br style="clear:both;" />
 +
 +
=== Cold-start of AMC application only, keep IP setting ===
 +
[[Image:Cold Start of AMC-IP.2.jpg|right|200px|thumb|Cold-start of AMC application]]
 +
*Press the reset button on the [[APC|APC board]] briefly.
 +
*After 10 seconds, press the cold start button on the AMC-IP board.
 +
*Keep the cold start button pressed until the AMC status LED is blinking green.
 +
<br style="clear:both;" />
 +
 +
===Modify Factory Default Settings===
 +
After cold start the system is set up with a default program and is working without any further programming. To change or add to the default settings, the [[AlphaPro]] programming tool must be used.
 +
 +
===Other methods of factory default===
 +
A factory default can also be achieved in other ways:
 +
* '''From [[AlphaWeb]]''': System Maintenance -> System Recovery -> Load Factory Defaults
 +
* '''From [[AlphaPro]]:''' Upload a default AlphaPro database to the exchange
 +
 +
=Upgrade=
 +
===Software upgrade===
 +
See [[AMC-IP software upgrade]]
 +
 +
===Hardware Upgrade===
 +
See [[AlphaCom Exchange Upgrade]]
 +
 +
= Additional Documentation on Zenitel.com=
 +
* [http://www.zenitel.com/product/alphacom-xe26 Additional Documentation on Zenitel.com]
  
 
[[Category:AlphaCom Servers]]
 
[[Category:AlphaCom Servers]]

Latest revision as of 14:22, 27 February 2018

AlphaCom XE26 Audio Server with HD Voice

Highlights

  • Made to provide critical communication in any environment
  • Supports 552 IP stations and 138 analog intercom stations
  • SIM card based software configuration and disaster recovery
  • Fully compatible with any AlphaCom system

Variants

There are three standard cabinet models: 19” rack mounting, floor cabinet, and floor cabinet with distribution field:

Mounting AlphaCom XE26


Mounting & Dimensions

The cabinet has room for installation of 26 circuit boards in total: one AMC-IP processor board, one APC program & clock board, and up to 24 feature boards. The server also includes a mains power supply and a cooling fan.

Front View


Rear View


Top View


Side View


Board positions

Board positions and physical numbers in AlphaCom XE20 seen from the rear


Connections

XE26 Connections.PNG


Power

The exchange is powered from the mains.

Network

Two RJ-45 Ethernet terminals on the IP filter board are used for IP LAN and WAN communication

Analogue Intercom Stations

The two-pair star wired intercom cables are connected to connection boards on the cabinet DIN rail or in a separate distribution field

Program Input

6 program distribution sources can be connected to the APC board via an optional program connection board. Up to 64 extra programs may be added using AGA boards with 16 programs per board

Serial Ports

The serial ports with RS232 and RS422/RS485 interfaces are used for connecting to equipment using these protocols

AMC-IP-Connections.PNG


Serial Port 0

RJ45 (RS232 Only)

No additional settings necessary

Serial Port 1

RJ45 (RS232/422/485)

Additional settings:
RS232:
RS422/485:
  • Switch 8 on S601 on the AMC-IP board must be set to ON.
  • Use the two jumpers on the AMC-IP Filterboard to select between RS422 and RS485.
RS422/485 selector for Serial Port 1 on the XE26 AMC-IP Filterboard


Remote Control Inputs (RCI)

Connections

The optional program connection board has input for 6 Remote Control Inputs (RCI) which can initiate programmed actions

RCI inputs in an AlphaCom XE20 and XE26


Configuration

In AlphaPro there is an RCI table, where the physical address of the input is entered, along with the desired actions. The physical address is given as device + pin-number.

The RCI table supports up to 140 inputs.

  • For internal RCIs in the AlphaCom XE1, the device address is 68, and the pin number is 1-6.
  • Internal pin number 8 is the temperature alarm
  • Mappings for the internal RCI's are autoloaded. Mappings for external RCI's (Slave modules, RIO's or IPARIO) must be manually programmed.
  RCI Type Device/Station physical Number Pin Number
AlphaCom XE26 Device 65-68 1 - 6

Example

Start fire alarm message and activate rotating lamp:

RCI Conf Example1.PNG


RCI Conf Example2.PNG


AMG 1 3 - Alarm Message 3 (8193) to group 1 (84)
RCO 5 ON – Turn on the relay that controls the lamp
AMG 1 0 – Alarm Message OFF to group 1 (84)
RCO 5 OFF – Turn off the lamp

Note: Multiple commands are separated by semicolon ( ; )

Remote Control Outputs (RCO)

Each subscriber line card provides 6 freely programmable Remote Control Outputs (RCO)

Device # of RCO's Comment Hardware required
AlphaCom XE26]] 138 6 RCOs per ASLT card or ATLB-12 card MRBD relay board + PDB Power Distribution Board

Factory Reset (coldstart)

Performing a cold start of the AMC-IP board will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0.

Cold start button on AMC-IP board


Cold start procedure

Cold start to load default factory settings
  • Press the reset button on the APC board briefly while keeping the cold start button pressed.
  • Keep the cold start button pressed at least 2 sec. after power on. The AMC status LED will blink green when the boot is ready.


Cold-start of AMC application only, keep IP setting

Cold-start of AMC application
  • Press the reset button on the APC board briefly.
  • After 10 seconds, press the cold start button on the AMC-IP board.
  • Keep the cold start button pressed until the AMC status LED is blinking green.


Modify Factory Default Settings

After cold start the system is set up with a default program and is working without any further programming. To change or add to the default settings, the AlphaPro programming tool must be used.

Other methods of factory default

A factory default can also be achieved in other ways:

  • From AlphaWeb: System Maintenance -> System Recovery -> Load Factory Defaults
  • From AlphaPro: Upload a default AlphaPro database to the exchange

Upgrade

Software upgrade

See AMC-IP software upgrade

Hardware Upgrade

See AlphaCom Exchange Upgrade

Additional Documentation on Zenitel.com