Actions

Difference between revisions of "Automatic Gain Control (AGC)"

From Zenitel Wiki
Line 34: Line 34:
  
  
−
*'''Enable AVC''': Check the box to enable automatic volume control. Volume is adjusted according to the ambient noise level. The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note that the AVC adjustment is disabled while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required).
+
*'''Enable AGC''': Check the box to enable automatic volume control. Volume is adjusted according to the ambient noise level. The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note that the AVC adjustment is disabled while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required).
 
*'''Debug in Display''': When enabled the station shows current volume level in the OLED display (applicable to TCIS-4, TCIx-5 and TCIx-6 stations)
 
*'''Debug in Display''': When enabled the station shows current volume level in the OLED display (applicable to TCIS-4, TCIx-5 and TCIx-6 stations)
−
*'''AVC Advanced Settings''': Check to open for more advanced AVC settings
+
*'''AGC mode''': Check to open for more advanced AVC settings
−
** '''Lower Threshold''': Threshold level for the AVC to start working. Valid range: 30-80 dBA. Default is 55 dBA.
+
* '''AGC gain profile''': Threshold level for the AVC to start working. Valid range: 30-80 dBA. Default is 55 dBA.
−
** '''Upper Threshold''': Threshold level for the AVC to stop working. Valid range: 60-120 dBA. Default is 100 dBA.
+
** '''AGC speed''': Threshold level for the AVC to stop working. Valid range: 60-120 dBA. Default is 100 dBA.
−
** '''Attack Rate''': How quickly the AVC adjusts gain on raising ambient audio level. Range: 1..100 dBA/sec. Default is 10 dBA/sec.
+
 
−
** '''Decay Rate''': How quickly the AVC adjusts gain on falling ambient audio level. Range: 1..100 dBA/sec. Default is 10 dBA/sec.
 
−
** '''Hysteresis''': Hysteresis around previous set ambient audio level before doing adjustments. Range: 1..10 dBA/sec. Default is 3 dBA.
 
−
** '''Far-End Lockout Time''': When playing audio in AVC zone (far-end-signal) AVC adjustments are locked. When there is a pause in the far-end-signal, adjustment commences after this lockout-time. Range: 1..100. Resolution is 100 ms. Default is "1" (= 100 ms).
 
  
 
[[Category: ICX-AlphaCom features]]
 
[[Category: ICX-AlphaCom features]]

Revision as of 16:37, 23 October 2023

AEIS.png
icon This article is under construction!


Zenitel IP devices supports Automatic Gain Control (AGC). The purpose of the AGC feature ..............


Default active???

Not config in TCIV+?


IC-Edge mode

Log in to the Edge Controller, and navigate to Edge Controller > System Configuration > Call and Audio, and enable "AGC":

Enabling AGC in an IC-Edge system



SIP and ICX-AlphaCom mode

Log in to the Zenitel IP device.

  • SIP mode: Navigate to SIP Configuration > Audio Settings, and enable "Automatic Gain Control (AGC)"
  • ICX-AlphaCom mode: Navigate to Advanced ICX-AlphaCom > Audio Settings, and enable "Automatic Gain Control (AGC)"
Enabling AGC on a device in SIP or ICX-AlphaCom mode (screenshot from firmware 7 and later)



Some additional settings are available in Advanced Configuration mode. Navigate to Audio Settings > Audio signal processing:

Advanced AGC settings (screenshot from firmware 7 and later)



  • Enable AGC: Check the box to enable automatic volume control. Volume is adjusted according to the ambient noise level. The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note that the AVC adjustment is disabled while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required).
  • Debug in Display: When enabled the station shows current volume level in the OLED display (applicable to TCIS-4, TCIx-5 and TCIx-6 stations)
  • AGC mode: Check to open for more advanced AVC settings
  • AGC gain profile: Threshold level for the AVC to start working. Valid range: 30-80 dBA. Default is 55 dBA.
    • AGC speed: Threshold level for the AVC to stop working. Valid range: 60-120 dBA. Default is 100 dBA.
Retrieved from "https://wiki.zenitel.com/w/index.php?title=Automatic_Gain_Control_(AGC)&oldid=234328"