Actions

Difference between revisions of "Broadcast messages (ACDP)"

From Zenitel Wiki
Line 26: Line 26:
 
|-
 
|-
 
|[[CONF_NOT_ROOT  ]] || align=center | || align=center |0x007C || Broadcast message. Sender informs that it is no longer root of conference  
 
|[[CONF_NOT_ROOT  ]] || align=center | || align=center |0x007C || Broadcast message. Sender informs that it is no longer root of conference  
−
|-
 
−
|[[SET_GRP_FILT ]] || align=center | GFLT || align=center | 0x007D || Set group call filter for a station
 
−
|-
 
−
|[[CONSOLE_REQ  ]] || align=center | || align=center |0x007E || Log on to system debug console (TST)
 
−
|-
 
−
|[[CONSOLE_DISC ]] || align=center |  || align=center |0x007F || Log off from system debug console (TST)
 
−
|-
 
−
|[[NAME_EXTENSION ]] || align=center |   || align=center | 0x0080  || Special exchange mode using two line names: Send the second line through AlphaNet
 
−
|-
 
−
|[[GROUP_MEMBERSHIP ]] || align=center | GRM || align=center | 0x0081  || Set group membership in NVRAM for a station
 
−
|-
 
−
|[[SET_MAIL_TIMEOUT ]] || align=center | SMT || align=center | 0x0082  || Set the timer of a mail queue entry
 
−
|-
 
−
|[[COPY_MAIL  ]] || align=center |CPYM || align=center |0x0083  || Send a copy of a mail in own queue to a new destination (station or group)
 
−
|-
 
−
|[[RCI_CHANGED]] || align=center | $RCIC || align=center | 0x0084  ||New RCI state reported from the exchange
 
−
|-
 
−
|[[RCO_CHANGED  ]] || align=center | RCOC|| align=center | 0x0085  || New RCO state reported from the exchange
 
−
|-
 
−
|[[PARK_INQ_BROKER ]] || align=center | INQ || align=center | 0x0086  || Park station from conversation, enter Inquiry call state
 
−
|-
 
−
|[[UNPARK ]] || align=center |  || align=center | 0x0087  || Unpark station from Inquiry call state station, return to conversation
 
−
|-
 
−
|[[REQ_TRANSF_CALL  ]] || align=center | TRFC || align=center | 0x0088  || Transfer call in an Inquiry Call situation.
 
−
|-
 
−
|[[WRITE_USER_DEF_DATA ]] || align=center | WUDD || align=center | 0x008A  || Write User Defined Data (UDD)
 
−
|-
 
−
|[[CONF_TALK ]] || align=center |  || align=center |0x008B || Set Simplex conference speaker
 
−
|-
 
−
|[[CONF_TALK_STOP ]] || align=center | || align=center |0x008C  || Stop station form feeding Simplex conference
 
−
|-
 
−
|[[MAILQ_NAVIG ]] || align=center |  || align=center | 0x008D  || Do operation on mail queue, or step current mail in mail queue
 
−
|-
 
−
|[[DISCON_ST ]] || align=center | || align=center |0x008E  || Disconnect station from ongoing feature
 
−
|-
 
−
|[[SET_TIMER ]] || align=center | ST  || align=center | 0x008F || Start or stop a timer
 
−
|-
 
−
|[[SET_STATION_COS ]] || align=center | SSC || align=center | 0x0090 || Set COS membership in NVRAM for a station
 
−
|-
 
−
|[[MODIFY_COS_CONTENTS]] || align=center | $MCC || align=center | 0x0091 || Modify feature membership in COS in NVRAM
 
−
|-
 
−
|[[GLOBAL_SEARCH]]|| align=center |  || align=center | 0x0092 || internally used for timeout of call request in AlphaNet
 
−
|-
 
−
|Unused|| align=center |  || align=center | 0x0093 || Unused
 
−
|-
 
−
|[[DIAL_DAK ]] || align=center | || align=center |0x0094  || Dial DAK on a station
 
−
|-
 
−
|[[SNV  ]] || align=center | SNV || align=center | 0x0095 || Update specific system settings (NVRAM) values
 
−
|-
 
−
| [[TEMP_PROG]] ||align=center| ||align=center|0x0096|| Temporarily "mute" program distribution to a station
 
−
|-
 
−
| [[DTMF_CONN]] ||align=center| ||align=center|0x0097|| Generate DTMF tone during conversation (Only during conversation with RingMaster)
 
−
|-
 
−
|[[PAR_RING]] ||align=center|    ||align=center  | 0x0098 || Add a Parallel Ringer station to a call in ringing state
 
−
|-
 
−
|[[GET_ST_STATE]]|| align=center |  || align=center | 0x0099 || Get status for a station
 
−
|-
 
−
|[[ST_STATE]]|| align=center |  || align=center | 0x009A || Status of a station. response to GET_ST_STATUS
 
−
|-
 
−
|[[RESET_AUDIO_LINK]] || align=center |   || align=center | 0x8000 || Reset audio link between nodes
 
−
|-
 
−
|[[AUDIO_PATH_SETUP  ]] || align=center | || align=center |0x8001 || Set up audio path between a source node and a destination node (possibly via
 
−
 
−
transit nodes)
 
−
|-
 
−
|[[AUDIO_PATH_OK ]] || align=center | || align=center |0x8002 || End to end message: Audio path is ready
 
−
|-
 
−
|[[AUDIO_LINK_OK ]] || align=center |  || align=center |0x8003|| Response to AUDIO_PATH_SETUP. Channel number is OK
 
−
|-
 
−
|[[AUDIO_LINK_NOT_AVAILABLE ]] || align=center |  || align=center |0x8006 || Response to AUDIO_PATH_SETUP from next node: Channel not granted
 
−
|-
 
−
|[[AUDIO_LINK_RELEASE ]] || align=center |  || align=center |0x8005 || Used to release audio path backwards stepwise from node to node when setup meets
 
−
 
−
busy or faulty link
 
−
|-
 
−
|[[AUDIO_PATH_DISCONNECT  ]] || align=center | || align=center |0x8006  || Release the end­to­end audio path. Normal disconnect from source or
 
−
 
−
destination
 
−
|-
 
−
|[[AUDIO_PATH_DELAY  ]] || align=center | || align=center |0x8007  || Set Duplex switch delay
 
−
|-
 
−
|[[CHECK_AUDIO_PATH ]] || align=center | || align=center |0x800E || Check of established audio path at regular intervals
 
−
|-
 
−
|[[AUDIO_PATH_CHECK_OK ]] || align=center | || align=center |0x800F || Positive response to CHECK_AUDIO_PATH
 
−
|-
 
−
|[[AUDIO_CH_LOOPBACK_REQ ]] || align=center |  || align=center |0x8010  || Request for loopback audio connection. Used by the Audio Channel Testing
 
−
 
−
process 
 
−
|-
 
−
|[[AUDIO_CH_LOOPBACK_ACK]] || align=center |  || align=center |0x8011  ||Positive acknowledge of AUDIO_CH_LOOPBACK_REQ
 
−
|-
 
−
|[[AUDIO_CH_DISCON]] || align=center |  || align=center |0x8012  || Disconnect a audio channel after loopback test 
 
−
|-
 
−
|[[AUDIO_CH_FAULTY ]] || align=center |  || align=center |0x8013  || Response to AUDIO_CH_LOOPBACK_REQ: Requested channel was faulty
 
−
|-
 
−
|[[LOOPBACK_IMPOSSIBLE ]] || align=center |   || align=center | 0x8014  || Response to AUDIO_CH_LOOPBACK_REQ
 
−
|-
 
−
|[[AUDIO_CH_TONE_REQ ]] || align=center |  || align=center |0x8015 || Request a peer exchange to put a 500Hz tone on a audio channel
 
−
|-
 
−
|[[AUDIO_M_PATH_SETUP ]] || align=center | || align=center |0x8016  || Communication in a multi-node network
 
−
|-
 
−
|[[AUDIO_M_PATH_OK ]] || align=center | || align=center |0x8017 || Contains statuses for an AUDIO_M_PATH_SETUP from one or more destination exchanges
 
−
|-
 
−
|[[AUDIO_M_PATH_BACKTRACK  ]] || align=center | || align=center |0x8018 || AUDIO_M_PATH_SETUP failed
 
−
|-
 
−
|[[AUDIO_M_LINK_OK ]] || align=center |   || align=center |0x8019  || Per­ hop positive response to AUDIO_M_PATH_SETUP
 
−
|-
 
−
|[[AUDIO_M_FEED_REQ ]] || align=center | || align=center |0x801A || Global Simplex Conference: Some station is pressing the M-key when participating in
 
−
 
−
a conference
 
−
|-
 
−
|[[AUDIO_M_FEED_STOP ]] || align=center | || align=center |0x801B  || Global Simplex Conference: The station is releasing the M-key 
 
−
|-
 
−
|[[DUMMY  ]] || align=center | || align=center |0xFFFE  || Test message: Should be routed, accepted and ignored
 
 
|-
 
|-
 
|}
 
|}

Revision as of 21:32, 11 September 2007

This article shows some examples of the ACDP broadcast messages transmitted from the AlphaCom.

Message Short name Message no, Hex Description
ST_BUSY_BC   0x0036 Broadcast message: Intercom station is busy
ST_FREE_BC   0x0037 Broadcast message: Intercom station is free
CALL_STATUS_BC   0x0040 Broadcast message telling the status of a call
CONN_STATUS_BC   0x0041 Broadcast message telling that a connection is established
DISCON_STATUS_BC   0x0042 Broadcast message telling that a connection is disconnected
EXT_FEATURE_BC   0x0043 Broadcast message when a directory number (feature 50) is dialed on a station
Q_ELEM_ADDED   0x004B Broadcast message. Reports that a mail message has been added to a station’s mail queue
Q_ELEM_REMOVED   0x004C Broadcast message. Reports that a mail message has been removed from a station’s mail queue
CONF_IS_ROOT   0x007B Broadcast message. Sender informs that it is root of conference
CONF_NOT_ROOT   0x007C Broadcast message. Sender informs that it is no longer root of conference


The messages below are broadcast messages transmitted from the AlphaCom on the AlphaCom Data Protocol when a call is initiated by the command: $CALL L8002 L8009

014101FF2118410015003632018002=54
014101FF2119410016003632018009=5D
014101FF211A410017004007D706070B1A2D32018002320180090201=76
014101FF211B410018004107D706070B1A2D01043201800232018009=7F

Message explanation

Space is added for better readability. 

Message 014101FF2118410015003632018002=54 

0141 01FF 21 18 41 0015 0036 32018002 = 54
---- ---- -- -- -- ---- ---- -------- - --
 !    !   !  !  !   !    !       !    ! +- Checksum
 !    !   !  !  !   !    !       !    +--- Checksum next
 !    !   !  !  !   !    !       +-------- Station in NET_OBJ_REF format: dir no 8002, node 01
 !    !   !  !  !   !    +---------------- Message id: 0x0036 = Station is busy
 !    !   !  !  !   +--------------------- Reference: Value identifying receivers’ reference
 !    !   !  !  +------------------------- Message class: 65 (0x41) ‘A’ = AlphaCom
 !    !   !  +---------------------------- Options: The number of bytes is given by <hop­count­byte>
 !    !   +------------------------------- Hopcount byte
 !    +----------------------------------- Destination: Node 01, broadcast (0xFF)
 +---------------------------------------- Source: Node 01, module 65 (0x41)
Retrieved from "https://wiki.zenitel.com/w/index.php?title=Broadcast_messages_(ACDP)&oldid=58522"