Difference between revisions of "Configuration of the IP Vandal Resistant Substation TKIE"
From Zenitel Wiki
| Line 1: | Line 1: | ||
| − | {{ | + | {{AEPS}} |
| − | + | The call button and station LED on the IP Vandal Resistant Substation TKIE must be configured. | |
| − | The | ||
| − | == | + | ==Alphacom - ICX Mode== |
| − | Log into the station webserver and navigate to the I/O settings. | + | |
| + | ===Call Button=== | ||
| + | The call button is connected to input 1, and is by default set as input. | ||
| + | Input 1 is programmed in AlphaPro as DAK 11 in DAK window, or as sybtype 11 in event 30. | ||
| + | Example shows DAK 11 doing Call Request to station 101: | ||
| + | [[File:TKIE_DAK.png|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | Example shows input 1 calling station 101 using event 30: | ||
| + | [[File:Input1.PNG|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ===LED Settings=== | ||
| + | |||
| + | Log into the '''station webserver''' and navigate to the I/O settings. | ||
| + | The station LED is from factory wired to output 2. | ||
Choose I/O and set it as Output. | Choose I/O and set it as Output. | ||
| − | [[File: | + | [[File:Output2.png|thumb|left|700px]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | ==Control the LED== | + | ===Control the LED=== |
Use the event handler and define situations where the station LED shall be lit: | Use the event handler and define situations where the station LED shall be lit: | ||
| − | * | + | * Microphone active: |
| − | [[File: | + | [[File:TKIE_MicOpen.png|thumb|left|700px]] |
| + | <br style="clear:both;" /> | ||
| + | |||
| + | * Call Request and Ringing Group call with blinking LED: | ||
| + | [[File:TKIE_CRmode.png|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ==IC-Edge Mode== | ||
| + | ===Call button=== | ||
| + | The call button is connected to input 1, and is by default set as input. The input is programmed in Edge Controller -> System Configuration -> Direct Access Key (DAK) and Buttons and Inputs. | ||
| + | The example below shows how to set up a call to directory number 101. The conversation will be ended if input or call button is pressed during conversation. | ||
| + | |||
| + | [[File:TKIE_Edge_Callbutton.PNG|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ===LED Settings=== | ||
| + | |||
| + | [[Advanced_Configuration_Mode_(Edge)|Advanced configuration mode]] must be enabled to make the following changes. | ||
| + | |||
| + | Log into the '''station webserver''' and navigate to the I/O settings. | ||
| + | The station LED is from factory wired to output 2. | ||
| + | |||
| + | Choose I/O and set it as Output. | ||
| + | [[File:Output2.png|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ===Control the LED=== | ||
| + | In Edge controller, go into System Configuration -> Special Setting and select Relay setting. | ||
| + | |||
| + | Choose to configure output 2 in the listbox. The recommended settings are shown below: | ||
| + | |||
| + | [[File:TKIE_Edge_Output2.png|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ==SIP Mode== | ||
| + | |||
| + | ===Call Button=== | ||
| + | |||
| + | The call button is connected to input 1, and is by default set as input. The input is programmed in SIP Configuration -> Direct Access Key (DAK). | ||
| + | The example below shows how to set up a call to directory number 101. The conversation will be ended if input or call button is pressed during conversation. | ||
| + | |||
| + | [[File:TKIE_SIP_CallButton.png|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ===LED Settings=== | ||
| + | |||
| + | [[Advanced_Configuration_Mode_(Edge)|Advanced configuration mode]] must be enabled to make the following changes. | ||
| + | |||
| + | Log into the '''station webserver''' and navigate to the I/O settings. | ||
| + | The station LED is from factory wired to output 2. | ||
| + | |||
| + | Choose I/O and set it as Output. | ||
| + | [[File:TKIE_SIP_io2.png|thumb|left|700px]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | ===Control the LED=== | ||
| + | |||
| + | In the station web server, go into SIP Configuration -> Relays/Outputs. | ||
| + | |||
| + | Choose to configure output 2 in the listbox. The recommended settings are shown below: | ||
| + | |||
| + | [[File:TKIE_SIP_Output2.png|thumb|left|700px]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
Revision as of 14:20, 28 May 2021
The call button and station LED on the IP Vandal Resistant Substation TKIE must be configured.
Contents
Alphacom - ICX Mode
Call Button
The call button is connected to input 1, and is by default set as input. Input 1 is programmed in AlphaPro as DAK 11 in DAK window, or as sybtype 11 in event 30. Example shows DAK 11 doing Call Request to station 101:
Example shows input 1 calling station 101 using event 30:
LED Settings
Log into the station webserver and navigate to the I/O settings. The station LED is from factory wired to output 2.
Choose I/O and set it as Output.
Control the LED
Use the event handler and define situations where the station LED shall be lit:
- Microphone active:
- Call Request and Ringing Group call with blinking LED:
IC-Edge Mode
Call button
The call button is connected to input 1, and is by default set as input. The input is programmed in Edge Controller -> System Configuration -> Direct Access Key (DAK) and Buttons and Inputs. The example below shows how to set up a call to directory number 101. The conversation will be ended if input or call button is pressed during conversation.
LED Settings
Advanced configuration mode must be enabled to make the following changes.
Log into the station webserver and navigate to the I/O settings. The station LED is from factory wired to output 2.
Choose I/O and set it as Output.
Control the LED
In Edge controller, go into System Configuration -> Special Setting and select Relay setting.
Choose to configure output 2 in the listbox. The recommended settings are shown below:
SIP Mode
Call Button
The call button is connected to input 1, and is by default set as input. The input is programmed in SIP Configuration -> Direct Access Key (DAK). The example below shows how to set up a call to directory number 101. The conversation will be ended if input or call button is pressed during conversation.
LED Settings
Advanced configuration mode must be enabled to make the following changes.
Log into the station webserver and navigate to the I/O settings. The station LED is from factory wired to output 2.
Choose I/O and set it as Output.
Control the LED
In the station web server, go into SIP Configuration -> Relays/Outputs.
Choose to configure output 2 in the listbox. The recommended settings are shown below:
