Difference between revisions of "Fader Resource"
From Zenitel Wiki
(→Realization) |
(→Realization) |
||
| (9 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| + | {{A}} | ||
Fader Resources are used in the AlphaCom System for providing clickfree audio switching between sources in group audio features. | Fader Resources are used in the AlphaCom System for providing clickfree audio switching between sources in group audio features. | ||
= Usage = | = Usage = | ||
| − | One fader resource is used when one of the following functions | + | One fader resource is used when activating one of the following functions: |
| − | * Groupcall | + | * Groupcall - switch between gong tone and microphone, fade in/out when m-key is pressed/released. |
* Simplex conference | * Simplex conference | ||
| − | In a | + | In a [[MultiModule]], one fader is needed in each participant module. |
| − | A fader is used along with two timeslots. The audio source is connected to the source timeslot. The fader loops the audio to the distribution timeslot. All listeners listen on the distribution timeslot. When switching sources, the fader fades out the source audio, and keep feeding the distribution timeslot during the switch. The listeners are not involved in the switch. | + | A fader is used along with two timeslots. The audio source is connected to the source timeslot. The fader loops the audio to the distribution timeslot. All listeners listen on the distribution timeslot. When switching sources, the fader fades out the source audio, and keep feeding the distribution timeslot during the switch. The listeners are not involved in the switch. |
= Realization = | = Realization = | ||
| Line 16: | Line 17: | ||
We use the otherwise unused SBI subchannel 0 of the Audio Scanners as Fader Resource. (All SBI Channel has a fader function on subchannel 0). The SBI subchannel is set in Loopback mode when used as Fader Resource. | We use the otherwise unused SBI subchannel 0 of the Audio Scanners as Fader Resource. (All SBI Channel has a fader function on subchannel 0). The SBI subchannel is set in Loopback mode when used as Fader Resource. | ||
| − | + | Fader resources are found on these boards: | |
| − | * ASLT | + | * AMC-IP: 12 faders (from AMC 10.31) |
| − | * ATLB | + | * ASLT: 2 faders |
| − | * | + | * ATLB-12: 4 faders |
| + | * ATLB: 2 faders | ||
| − | |||
| − | |||
| − | [[Category: | + | The AMC-IP board provides 12 fader resources, by using unused "SBI channels" realized by the FPGA. These faders limits the audio to 7 kHz bandwidth. The AMC SW will use SBI based faders if available, and fall back to FPGA faders if no SBI faders are available. For FPGA faders, audio is looped via the DSP. This is because treble deemphasis is done in FPGA, while the preempasis is done in DSP. |
| + | |||
| + | Also see: [[AlphaCom Audio Switching Hardware]]. | ||
| + | |||
| + | [[Category: AMC Software]] | ||
Latest revision as of 08:17, 8 September 2017
Fader Resources are used in the AlphaCom System for providing clickfree audio switching between sources in group audio features.
Usage
One fader resource is used when activating one of the following functions:
- Groupcall - switch between gong tone and microphone, fade in/out when m-key is pressed/released.
- Simplex conference
In a MultiModule, one fader is needed in each participant module.
A fader is used along with two timeslots. The audio source is connected to the source timeslot. The fader loops the audio to the distribution timeslot. All listeners listen on the distribution timeslot. When switching sources, the fader fades out the source audio, and keep feeding the distribution timeslot during the switch. The listeners are not involved in the switch.
Realization
We use the otherwise unused SBI subchannel 0 of the Audio Scanners as Fader Resource. (All SBI Channel has a fader function on subchannel 0). The SBI subchannel is set in Loopback mode when used as Fader Resource.
Fader resources are found on these boards:
- AMC-IP: 12 faders (from AMC 10.31)
- ASLT: 2 faders
- ATLB-12: 4 faders
- ATLB: 2 faders
The AMC-IP board provides 12 fader resources, by using unused "SBI channels" realized by the FPGA. These faders limits the audio to 7 kHz bandwidth. The AMC SW will use SBI based faders if available, and fall back to FPGA faders if no SBI faders are available. For FPGA faders, audio is looped via the DSP. This is because treble deemphasis is done in FPGA, while the preempasis is done in DSP.
Also see: AlphaCom Audio Switching Hardware.