Difference between revisions of "Flowire Software Upgrade Procedure"
From Zenitel Wiki
(→Create the special USB-Serial cable) |
|||
| Line 15: | Line 15: | ||
== Create the special USB-Serial cable == | == Create the special USB-Serial cable == | ||
* You need an RS232 cable with 3,3V TTL level. For example: http://au.element14.com/ftdi/ttl-232r-3v3/connector-type-a/dp/1329311 | * You need an RS232 cable with 3,3V TTL level. For example: http://au.element14.com/ftdi/ttl-232r-3v3/connector-type-a/dp/1329311 | ||
| + | * You also need a ribbon cable. Suggested type: http://no.farnell.com/harwin/m50-9011042/receptacle-to-dip-150mm-20way/dp/2289813 | ||
* Create an adapter cable to connect to the debug connector on Flowire: | * Create an adapter cable to connect to the debug connector on Flowire: | ||
[[File:Flowire cable.PNG|thumb|left|500px|Flowire cable]] | [[File:Flowire cable.PNG|thumb|left|500px|Flowire cable]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | |||
* On the Flowire, you must connect to these pins: | * On the Flowire, you must connect to these pins: | ||
** 7: GND | ** 7: GND | ||
| Line 26: | Line 26: | ||
[[File:FlowirePins.PNG|thumb|left|500px|Flowire pinning]] | [[File:FlowirePins.PNG|thumb|left|500px|Flowire pinning]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | |||
== PC setup == | == PC setup == | ||
Revision as of 14:18, 17 April 2015
This is a step by step guide to upgrading the software in Flowire through the serial interface.
Requirements
- Windows PC
- TFTPS server, for example Tftpd32 or Tftpd64 by Ph. Jounin (http://tftpd32.jounin.net)
- Telnet software, for example PuTTY by Simon Tatham (http://www.chiark.greenend.org.uk/~sgtatham/putty/)
- Simple network switch
- 2 Ethernet cables
- Special USB-Serial cable with JTAG connector
- Flowire unit
- Flowire power supply
Create the special USB-Serial cable
- You need an RS232 cable with 3,3V TTL level. For example: http://au.element14.com/ftdi/ttl-232r-3v3/connector-type-a/dp/1329311
- You also need a ribbon cable. Suggested type: http://no.farnell.com/harwin/m50-9011042/receptacle-to-dip-150mm-20way/dp/2289813
- Create an adapter cable to connect to the debug connector on Flowire:
- On the Flowire, you must connect to these pins:
- 7: GND
- 8: UART1_TX – Connect this to Rx on the serial cable
- 16: UART1_RX – Connect this to Tx on the serial cable
PC setup
- Set static IP address 169.254.1.2 on your PC
- Connect the USB-Serial cable
- Check the "Windows Device Manager" to see which serial port it chooses. It will be listed under “Ports (COM % LPT)” as USB Serial COM port #x, where x represents the COM port number. Double click it and change the port settings from 9600 baud to 115200 baud.
TFTP server setup
- Start the Tftpd
- From the main window browse to the folder where the software files are kept. Choose the PC LAN port as the server interface:
