Actions

Difference between revisions of "Honeywell Pro-Watch"

From Zenitel Wiki

(Introduction)
 
Line 4: Line 4:
  
 
Pro-Watch supports both serial and IP data connections. AlphaCom also support both methods, while in ICX one must use an Ethernet to Serial Converter if serial data is needed.  
 
Pro-Watch supports both serial and IP data connections. AlphaCom also support both methods, while in ICX one must use an Ethernet to Serial Converter if serial data is needed.  
 
== Configuration ==
 
For a '''serial data connection''' set the following parameters in AlphaPro, '''Exchange & System''' > '''Serial Ports''' (Applicable to AlphaCom only):
 
* Enable the MPC DataProtocol port
 
* Select either Serial 0 or Serial 1, depending on the port which will be used for the physical connection to Pro-Watch
 
* Bit Rate: 9600
 
* Parity: Even
 
* Data Bits: 7
 
* Stop Bits: 1
 
<br>
 
For an '''IP-link''' set the following parameters (Applicable to both AlphaCom and ICX):
 
* Enable the MPC DataProtocol port
 
* Select TCP/IP server
 
* Enter the TCP port number
 
 
In the Web interface make certain that the port is opened in the "Filters" page.
 
  
 
==Licenses ==
 
==Licenses ==
Line 25: Line 9:
  
 
==Capabilities==
 
==Capabilities==
* Once the ICX/AlphaCom has been defined in Pro-Watch, all individual STENTOFON intercom stations can be defined and be put onto graphical maps.
+
* Once the ICX/AlphaCom has been defined in Pro-Watch, all individual intercom stations can be defined and be put onto graphical maps.
 
* Intercom stations can be associated with Pro-Watch workstations, allowing operators to set up calls directly from the workstation.
 
* Intercom stations can be associated with Pro-Watch workstations, allowing operators to set up calls directly from the workstation.
* Remote intercom stations (normally sub-stations) can be associated with logical devices such as doors. A call can then be made via for instance a right click on the door icon.
+
* Remote intercom stations (normally sub-stations) can be associated with logical devices such as doors. A call can then be made via for instance a right-click on the door icon. Intercoms may also be called from the Alarm Monitor, see the Pro-Watch Software Suite User Guide for more details.
* Intercom station statuses such as calls between stations, or canceled calls are shown in an event viewer. The ICX/AlphaCom produces more events than are required in a specific installation; it is therefore possible to select the events of interest during commissioning, see the Pro-Watch installation guide for details.
+
* Intercom station statuses such as calls between stations, or canceled calls are shown in an event viewer. The ICX/AlphaCom produces more events than are required in a specific installation, it is, therefore, possible to select the events of interest during commissioning, see the Pro-Watch installation guide for details.
 
* All intercom calls, events and alarms that report into Pro-Watch are stored in the system database for future audit trail and reporting capabilities.
 
* All intercom calls, events and alarms that report into Pro-Watch are stored in the system database for future audit trail and reporting capabilities.
  
 +
==ICX System Configuration==
 +
Use AlphaPro, the standard ICX programming tool to enter the parameters to enable communication between ICX and Honeywell Pro-Watch.
 +
* Go to Exchange & System > Serial Ports and set the following parameters:
 +
** MPC Data Protocol
 +
** TCP/IP server
 +
** Enter a Port number
 +
*** In the screenshot, port 4005 is used as an example.
 +
 +
[[File:Prowatch_alphapro.png|thumb|left|700px|The port must be defined and opened in the ICX firewall]]
 +
<br clear=all/>
 +
 +
Use a web browser to log into the ICX webserver, (default username/password = admin/alphaadmin)
 +
* Select System Configuration > Filters
 +
[[File:Prowatch_icxweb.png|thumb|left|700px|Enable the selected TCP port]]
 +
<br clear=all/>
 +
 +
If the port is not in the list yet, use Add Filter to define it. In the above screenshot, it has been defined with the name Honeywell but any meaningful name can be given. Enable this TCP port on the relevant Ethernet port (Eth0 or Eth1).
 +
 +
==Pro-Watch configuration==
 +
The following steps are done in Pro-Watch under '''Hardware Configuration'''.
 +
 +
===Add a site===
 +
In the Hardware Configuration, create a site. To do this right-click in the Hardware Configuration tree view and select '''New
 +
> Site ''' to display the Add Sites dialog box.<br/>
 +
 +
Next, enter the required information:
 +
#Enter a Site ID, a unique name that identifies the site. You cannot have duplicate Site IDs.
 +
# Enter a Description of the site.
 +
# Click the icon next to the Workstation field and select the workstation that will poll the panel on this site.
 +
# Click the icon next to the Primary Workstation field and select the primary workstation that will poll the panel on this site.
 +
# Click the icon next to the Secondary Workstation field and select the secondary workstation that will poll the panel on this site.
 +
# Click OK. The new site appears in the tree view in the Pro-Watch Hardware Configuration window.
 +
 +
 +
[[File:Prowatch_addsite.png|thumb|left|700px|Add site]]
 +
<br clear=all/>
 +
 +
===Add and define a channel===
 +
 +
====Add a channel====
 +
Select the added site in the Hardware Configuration tree view, right-click and select '''New > Channel'''. From the dropdown menu set the channel type to Stentofon and click OK to proceed to define the channel.
 +
 +
[[File:Prowatch_addchannel.png|thumb|left|700px|Add the channel type]]
 +
<br clear=all/>
 +
 +
====Define the channel====
 +
# In the Define Channel Information dialog box, enter an identifying channel description.
 +
# Select the Installed check box. This assures the channel is installed and operational.
 +
# Select a time zone from the drop-down list.
 +
# Enter the maximum number of poll attempts.
 +
# Enter the poll delay interval between each polling. This number is in milliseconds.
 +
# Enter the communications break; the host must receive communication from the device within the specified time or the host will determine the communication as broken.
 +
# The spool directory is automatically created; this is where spool files temporarily reside during a download. The spool directory is created within the Pro-Watch directory.
 +
# Click Next to display the Communications Parameters dialog box.
 +
 +
 +
[[File:Prowatch_definechannel.png|thumb|left|700px|Define the channel]]
 +
<br clear=all/>
 +
 +
In the Communications Parameters window do the following steps:
 +
<ol>
 +
<li> Select a port type. Set the port type to '''TCP/IP'''.</li>
 +
<ul> <li> <span style="font-size:90%"> If serial port is used for the integration, the port type should be set to Hardwired</span> </li> </ul>
 +
<li> In the IP address field, enter the IP address of the ICX-Alphacom and the TCP port defined in the web interface in the next field. Click Next to display the Partitions dialog box. </li>
 +
 +
 +
[[File:Prowatch_commparam.png|thumb|left|700px|Define the IP address and port of the ICX-Alphacom]]
 +
<br clear=all/>
 +
 +
 +
<li> Add a partition if needed.</li>
 +
<li> Click Finish on the Partitions dialog box to complete adding the channel. A warning message appears notifying you to add the channel to the appropriate routing group</li>
 +
 +
 +
[[File:Prowatch_partitions.png|thumb|left|700px|Add partition if needed]]
 +
<br clear=all/>
 +
</ol>
 +
 +
If the connection is successful, the channel icon will be green.
 +
 +
[[File:Prowatch_icxconnected.png|thumb|left|700px|ICX-Alphacom is successfully integrated with Pro-Watch]]
 +
<br clear=all/>
 +
 +
===Add intercom===
 +
To add the intercoms in the system, in the hardware configuration tree view, right-click on the created channel
 +
 +
[[File:Prowatch_addintercom.png|thumb|left|700px|Add intercom]]
 +
<br clear=all/>
 +
 +
Enter the description for the intercom and in '''Address''' field enter the '''Directory number''' assigned to that intercom in the ICX-Alphacom
 +
If the intercom is to be a primary station, enable the primary station check box and click OK. In order for an intercom to be assigned to a workstation, the Primary station checkbox must be enabled.
 +
When an intercom is assigned to a workstation, that intercom allows a dispatcher to communicate with an individual at an access point.
 +
 +
[[File:Prowatch_intercomparam.png|thumb|left|700px|Enter the correct intercom parameters]]
 +
<br clear=all/>
 +
 +
Repeat the steps above for all intercoms that need to be added.
 +
 +
[[File:Prowatch intercoms.png|thumb|left|700px|Intercoms list]]
 +
<br clear=all/>
 +
 +
 +
===Assign an intercom to a workstation===
 +
In the Pro-Watch Database Configuration tree list, click Workstations to display in the right pane the icons of currently-configured workstations. Right-click the workstation you want to edit, and select Properties. The Edit Workstations dialog box appears.
 +
 +
# Go to '''Intercoms''' tab.
 +
# Click Add to see the list of primary stations.
 +
# Select the station that should be assigned to the selected workstation and click OK
 +
# Click OK to save the information
 +
 +
 +
[[File:Prowatch_assignintercom.png|thumb|left|700px|Assign an intercom to workstation]]
 +
<br clear=all/>
 +
 +
==Intercom controls==
 +
 +
The Intercom Controls dialog box allows you to define a source and target intercom and initiate a connection between the two. Intercom controls also allow you to assign a connection priority.
 +
 +
To display the intercom control dialog box, click the intercom icon marked on the image bellow
 +
 +
[[File:Prowatch_intercomicon.png|thumb|left|700px|Open intercom controls]]
 +
<br clear=all/>
  
 +
In the intercom controls window do the following steps:
 +
# Select the source intercom. The source intercom must be a primary intercom. You must add the primary intercom to the workstation before the drop-down list will be populated.
 +
# Select the target intercom. The target intercom can be any other intercom in the system.
 +
# Select the connection priority. Dial priority is the standard priority of a call. Low Priority Direct and High Priority Direct can be used to override calls that are in progress, which are of lower priority.
  
 +
[[File:Prowatch_intercomcontrols.png|thumb|left|700px|Start a call from the interface]]
 +
<br clear=all/>
  
 
[[Category:3rd party integration]]
 
[[Category:3rd party integration]]

Latest revision as of 13:57, 11 February 2022

AI.png

Introduction

The integration between ICX or AlphaCom and the Pro-Watch from Honeywell is via the MPC protocol.

Pro-Watch supports both serial and IP data connections. AlphaCom also support both methods, while in ICX one must use an Ethernet to Serial Converter if serial data is needed.

Licenses

  • When used with the ICX System, the following license is required in the ICX in order to enable the MPC protocol: 1002602400 - ILI-IF Interface enabling

Capabilities

  • Once the ICX/AlphaCom has been defined in Pro-Watch, all individual intercom stations can be defined and be put onto graphical maps.
  • Intercom stations can be associated with Pro-Watch workstations, allowing operators to set up calls directly from the workstation.
  • Remote intercom stations (normally sub-stations) can be associated with logical devices such as doors. A call can then be made via for instance a right-click on the door icon. Intercoms may also be called from the Alarm Monitor, see the Pro-Watch Software Suite User Guide for more details.
  • Intercom station statuses such as calls between stations, or canceled calls are shown in an event viewer. The ICX/AlphaCom produces more events than are required in a specific installation, it is, therefore, possible to select the events of interest during commissioning, see the Pro-Watch installation guide for details.
  • All intercom calls, events and alarms that report into Pro-Watch are stored in the system database for future audit trail and reporting capabilities.

ICX System Configuration

Use AlphaPro, the standard ICX programming tool to enter the parameters to enable communication between ICX and Honeywell Pro-Watch.

  • Go to Exchange & System > Serial Ports and set the following parameters:
    • MPC Data Protocol
    • TCP/IP server
    • Enter a Port number
      • In the screenshot, port 4005 is used as an example.
The port must be defined and opened in the ICX firewall


Use a web browser to log into the ICX webserver, (default username/password = admin/alphaadmin)

  • Select System Configuration > Filters
Enable the selected TCP port


If the port is not in the list yet, use Add Filter to define it. In the above screenshot, it has been defined with the name Honeywell but any meaningful name can be given. Enable this TCP port on the relevant Ethernet port (Eth0 or Eth1).

Pro-Watch configuration

The following steps are done in Pro-Watch under Hardware Configuration.

Add a site

In the Hardware Configuration, create a site. To do this right-click in the Hardware Configuration tree view and select New > Site to display the Add Sites dialog box.

Next, enter the required information:

  1. Enter a Site ID, a unique name that identifies the site. You cannot have duplicate Site IDs.
  2. Enter a Description of the site.
  3. Click the icon next to the Workstation field and select the workstation that will poll the panel on this site.
  4. Click the icon next to the Primary Workstation field and select the primary workstation that will poll the panel on this site.
  5. Click the icon next to the Secondary Workstation field and select the secondary workstation that will poll the panel on this site.
  6. Click OK. The new site appears in the tree view in the Pro-Watch Hardware Configuration window.


Add site


Add and define a channel

Add a channel

Select the added site in the Hardware Configuration tree view, right-click and select New > Channel. From the dropdown menu set the channel type to Stentofon and click OK to proceed to define the channel.

Add the channel type


Define the channel

  1. In the Define Channel Information dialog box, enter an identifying channel description.
  2. Select the Installed check box. This assures the channel is installed and operational.
  3. Select a time zone from the drop-down list.
  4. Enter the maximum number of poll attempts.
  5. Enter the poll delay interval between each polling. This number is in milliseconds.
  6. Enter the communications break; the host must receive communication from the device within the specified time or the host will determine the communication as broken.
  7. The spool directory is automatically created; this is where spool files temporarily reside during a download. The spool directory is created within the Pro-Watch directory.
  8. Click Next to display the Communications Parameters dialog box.


Define the channel


In the Communications Parameters window do the following steps:

  1. Select a port type. Set the port type to TCP/IP.
    • If serial port is used for the integration, the port type should be set to Hardwired
  2. In the IP address field, enter the IP address of the ICX-Alphacom and the TCP port defined in the web interface in the next field. Click Next to display the Partitions dialog box.
  3. Define the IP address and port of the ICX-Alphacom



  4. Add a partition if needed.
  5. Click Finish on the Partitions dialog box to complete adding the channel. A warning message appears notifying you to add the channel to the appropriate routing group
  6. Add partition if needed


If the connection is successful, the channel icon will be green.

ICX-Alphacom is successfully integrated with Pro-Watch


Add intercom

To add the intercoms in the system, in the hardware configuration tree view, right-click on the created channel

Add intercom


Enter the description for the intercom and in Address field enter the Directory number assigned to that intercom in the ICX-Alphacom If the intercom is to be a primary station, enable the primary station check box and click OK. In order for an intercom to be assigned to a workstation, the Primary station checkbox must be enabled. When an intercom is assigned to a workstation, that intercom allows a dispatcher to communicate with an individual at an access point.

Enter the correct intercom parameters


Repeat the steps above for all intercoms that need to be added.

Intercoms list



Assign an intercom to a workstation

In the Pro-Watch Database Configuration tree list, click Workstations to display in the right pane the icons of currently-configured workstations. Right-click the workstation you want to edit, and select Properties. The Edit Workstations dialog box appears.

  1. Go to Intercoms tab.
  2. Click Add to see the list of primary stations.
  3. Select the station that should be assigned to the selected workstation and click OK
  4. Click OK to save the information


Assign an intercom to workstation


Intercom controls

The Intercom Controls dialog box allows you to define a source and target intercom and initiate a connection between the two. Intercom controls also allow you to assign a connection priority.

To display the intercom control dialog box, click the intercom icon marked on the image bellow

Open intercom controls


In the intercom controls window do the following steps:

  1. Select the source intercom. The source intercom must be a primary intercom. You must add the primary intercom to the workstation before the drop-down list will be populated.
  2. Select the target intercom. The target intercom can be any other intercom in the system.
  3. Select the connection priority. Dial priority is the standard priority of a call. Low Priority Direct and High Priority Direct can be used to override calls that are in progress, which are of lower priority.
Start a call from the interface