Actions

Difference between revisions of "ICX Web"

From Zenitel Wiki

(User Management)
(User Management)
Line 377: Line 377:
  
 
{{note|
 
{{note|
''* [[Communicate_(alphaPro)|AlphaPro]] is using the "Read/Write User" credentials.''  
+
''* [[Communicate_(alphaPro)|AlphaPro]] is using the "Read/Write User" credentials.'' <br>
 
''* High Availability system (IPHA) is using the "Read/Write User" credentials.'' }}
 
''* High Availability system (IPHA) is using the "Read/Write User" credentials.'' }}
 
<br>
 
<br>

Revision as of 13:44, 18 September 2019

The web interface of the ICX-500 Gateway

This article describes the web interface of the ICX-500 Gateway.

The ICX-500 gateway runs an embedded web server. It allows the users to log in using a standard web browser such as Chrome or Firefox to operate and manage the ICX-500 system. The web server provides functions for system monitoring, configuration, and software upgrade.

Initial connection

Connect the laptop to Eth0, and enter 169.254.1.5 in the web browser

Logging in

Initial connection is done by connecting a laptop to Eth port 0, open a web browser (e.g. Firefox or Chrome), and type in the IP address in the address field of the browser:

The Login page


  • Default IP address 169.254.1.5
  • Default Username: admin
  • Default Password: alphaadmin

These credentials will give Read/Write privileges, making it possible to do changes in the configuration.

To log in with Read privileges only, the credentials are:

  • Default Username: alpha
  • Default Password: com

With these credentials one can check status and read information, but not make any changes to the system.

Changing Default User Name and Password

For security reasons it is recommended to change the default user names and passwords.

  • Select System Configuration > User Management
  • Enter the Current Password for both Read access and Read/Write access (default: com and alphaadmin)
  • Enter new User Name and Password
  • Re-enter the New Passwords to confirm
  • Verify by clicking Update User 1 and Update User 2
  • Write down the selected passwords and keep them in a secure place.

Saving and Applying changes

When new configuration parameters are entered, they are saved to the configuration file by clicking Save. To apply the new settings to the running configuration, click Apply.


System Monitoring

Node Information

Shows general information about the system such as Node Name and Node Number. It also shows state information; different times and memory usage. Information about the Software Configuration, and the Hardware Configuration (the different boards and versions), and also the state of the different processes running in the system.


Node Information


  • Node name: The name of the gateway, as configured from AlphaPro, Exchange & System > System menu.
  • Node number: Default node number is 1. The node number is used for communication between gateways interconnected in a network (AlphaNet). The node number can be changed from AlphaPro, Exchange & System > System menu.
  • Operational: Enabled: The intercom application (vs-amcd) is running. Disabled: The intercom application is not running.
  • Active Calls: Shows the number of currently active calls. Refresh (F5) the web page to see current status. If there is a need to restart the system, one can wait until there are no active calls in the system.
  • Current System Time: Shows the current time in the ICX-500, as presented in display stations.
  • System Uptime: The time elapsed since last time the system (Linux) started
  • ICXCORE Uptime: The time elapsed since last time the intercom application (vs-amcd) started
  • MAC Address: Shows the MAC address of the ICX-500.
  • Total Space (FLASH / DATA FLASH / RAMS): Total memory space.
    • FLASH: Memory space for program files, such as Linux and all program modules (vs-amcd, vs-sipd, vs-alphaweb etc.)
    • DATA FLASH: Memory space for storing of data, such as log files, voice messages and billing data (Not program files)
    • RAMFS: RAM File System for storing of temporary data, such as package uploads, web work files, Billing configuration and various status data.
  • Free Space (FLASH / DATA FLASH / RAMS): Available space in Flash memory.
  • Free RAM: Available space in RAM memory.
  • Active Partition: Show which of the two partitions A or B that is currently active.
  • ICXCORE System Package: Show the version of the software package running on the partition that is currently active.
  • Customer Database: The version of the customer database


Services
In the "Services" section one can see which software services are currently running, and their version number.


Stations/Devices

Configured

Stations/Devices - Configured


The table can be sorted by clicking on the relevant header. In the Search field you can search for any free text, e.g. directory number, display text or IP address. Click on Download device list to open the station list in Excel spreedsheet.

  • Physical Numbers: The physical number is the index number to which the station or device is assosiated.
  • Directory Number: The directory number is the number you must dial to reach the station.
  • Display Text: The caller ID of the station as programmed in AlphaPro, Users & Stations.
  • IP Address: The IP address of the IP Station or SIP Station. Clicking on the IP address will open a new tab in your browser and connect to that IP address.
  • MAC Address: Shows the MAC address of IP stations.
    • (0013cb00c7e9): When the MAC address is displayed in brackets, the station is "Registered with Directory Number". The MAC address will only show when the station is registered, else it will show DIP free MAC.
    • 0013CB00C7E9: When the MAC address is displayed without brackets, the station is configured in AlphaPro to "Register with its MAC address". The MAC address will show regardless if the station is registered or not.
    • DIP free MAC: The IP station is configured in AlphaPro to "Register with Directory Number", but is not registered.
    • SIP Station: The station is configured as a "SIP Station" in AlphaPro.
  • Status : Shows the registration status of the station
    • Not Registered: The IP station or SIP station is configured in the ICX, but has not been able to register.
    • Registered: The IP station or SIP station has successfully registered to the ICX.
    • No License: The registration was rejected due to missing license.
  • Type: Shows what type of equipment which is connected/registered.
    • 8020 - Dual Display Station
    • 8022 - INCA IP Sub Station
    • 8023 - Flush Master Station
    • 8024 - Desk Master Station
    • 8026 - IP ARIO
    • 8121 - Turbine Compact
    • 8124 - Turbine Extended
    • 8511 - TFIX station
    • 100 - SIP Phone/Station
    • 101 - IP Dummy Station
  • SW Ver: Shows the software version on the IP station.
  • HW Rev: Shows the IP station hardware version.
  • Reg Time: Registration Time. Shows the last time the station got registered to the ICX.
  • Reg Count: Registration Counter. Shows the number of registerations to the ICX-500 gateway. The counter will be cleared when the ICX is reset.
  • MC: MultiCast. Status information about Group Audio configuration (Groupcall, Audio Program, Simplex Conference) and status of the IP station.
    • UC: Unicast
    • M0 or M1: Direct multicast on ethernet ports 0 or 1
    • R0 to R4: Relayed multicast to Group 0 to 4
See Multicast for more details.

Unconfigured

The "Unconfigured" list shows stations that are able to connect to the ICX-500 gateway, but not able to register.

Typical reasons for not being able to register are:

  • The directory number specified in the station web does not exist in the ICX-500 gateway
  • The "CCoIP Station" flag is not enabled

Check "Directory Number" and "CCoIP Station" flag settings in AlphaPro, Users & Stations.

Stations/Devices - Unconfigured



AlphaNet

This table shows all AlphaNet and SIP Trunk connections.

System Monitoring - AlphaNet


The table shows:

  • Node ID: Unique index number (1 - 254) of the ICX node or the SIP Trunk node
  • Node Prefix: The prefix to dial on the intercom station to reach that node
  • Name: Shows the name of the node. If the name is changed from AlphaPro, a small reset is required for the name to be updated.
  • Type:
    • AC_IP: AlphaCom or ICX node.
    • SIP: SIP Trunk node.
  • SW Ver: Software Version of the node
  • Node IP: The IP Address of the node
  • Status: Shows the communication status to the remote node
    • Up: The communication with the node is OK
    • Down: Communication error with the node
  • Ping Test: Check if this node can do a ping request to the remote nodes. If Ping is OK, the ping time for each node will appear in the list

See also AlphaNet Troubleshooting


Audio Statistics

The ICX-500 collects Audio Statistics and RTP Statistics for local calls as well as for AlphaNet and SIP Trunk calls. The statistics are cleared when the ICX-500 is reset.

Audio Statistics


Audio Statistics:

  • Connection Type: Local calls inside this node, AlphaNet calls or SIP Trunk calls.
  • Connection Path: Shows between which nodes the statistics are for
  • Seconds of Audio: The total time of audio for all conversations
  • Connections: The number of connections since last reset
  • Max Lines: The peak of concurrent calls


RTP Statistics:
Click on View Details on one of the connections to see detailed RTP statistics for that connection:

  • Time (sec): Total duration of connections
  • Connections: Number of connections
  • TxPacktes: Count of RTP packets transmitted
  • RxPacktes: Count of RTP packets received in time playout
  • RxLate: Count of RTP packets received too late for playout
  • RxLost: Count of RTP packets not received at all
  • RxLost (‰): (RxLate / RxPacktes) * 1000
  • RxLost (‰): (RxLost / RxPacktes) * 1000

The "Jitter Avg" and "Delay Avg" are average values of the last 10 connections:

  • Jitter Avg (ms): Jitter computed as in A.8 of RFC3550, sampled once every second, and converted to milliseconds.
  • Delay Avg (ms): Localt Rx jitter buffer delay, sampled once every second, and converted to milliseconds.


Logs

Log files stored on the ICX-500 gateway can be viewed or downloaded by selecting System Monitoring > Logging.

View Logs


  • To view a log file directly in the browser, Select Log to read, then press Submit.
  • To download the log file, press the link under Filename, and store the log file on the laptop
Note icon By default logging is disabled. To enable logging, select System Configuration > Logging


System Configuration

Interfaces

There are two Ethernet interfaces on the ICX-500 Gateway, Eth0 and Eth1. The IP address is set by using CIDR notation. It appends a slash character ("/") to the address and a decimal number specifying the number of bits (out of the total 32 bits of an IP address) that the network prefix consists of.

Factory Default settings are:

  • Eth0: 169.254.1.5/16
  • Eth1: 0.0.0.0/32 (obtain IP Address automatically - DHCP)

Enter the IP address, press Validate, and then Save & Apply.

IP address and subnet mask is defined in CIDR notation


OBS icon It is highly recommended to use Static IP addresses on the ethernet ports


Examples of CIDR notation and equivalent dot-decimal notation:

  • 169.254.1.5/16 is equivalent to IP address 169.254.1.5 and net mask 255.255.0.0.
  • 10.5.101.30/24 is equivalent to IP address 10.5.101.30 and net mask 255.255.255.0.
  • 192.168.1.40/26 is equivalent to IP address 192.168.1.40 and net mask 255.255.255.192.

See here for more examples.


Routes

The Routing table must be configured if there is a need to communicate with devices outside own subnet. Three different route types can be defined:

  • Default route (= Default gateway)
  • Net route - A route to one particular IP network
  • Host route - A route to one particular host

Defining a Default Gateway

To define a Default Gateway, select Add New, and enter:

  • Destination net = 0.0.0.0/0
  • Gateway on local subnet = IP Address of the default gateway
  • Interface = On which Ethernet interface the default gateway is located
  • Press Validate
  • Press Save & Apply
Defining 10.9.8.1 as the Default Gateway on Eth1


OBS icon Only one Default Gateway must be defined.


Defining a Net Route

To define a route to one particular network, select Add New, and enter:

  • Destination net = IP address of the remote IP network in CIDR notation
  • Gateway on local subnet = IP Address of the gateway
  • Interface = On which Ethernet interface the gateway is located
  • Press Validate
  • Press Save & Apply
Defining a route to the network 10.9.3.0 via gateway 10.9.8.1 on Eth1


Defining a Host Route

To define a Host route, select Add New, and enter:

  • Destination net = <IP address of the host>/32
  • Gateway on local subnet = IP Address of the gateway
  • Interface = On which Ethernet interface the gateway is located
  • Press Validate
  • Press Save & Apply
Defining a route to the host 10.9.3.40 via the Gateway 10.9.8.1 on Eth1. Note that the CIDR mask must be "/32"


Filters

The built-in firewall of the ICX-500 Gateway is by default configured for management services (AlphaPro, Web Interface) on Ethernet port 0, and VoIP services (e.g. IP- and SIP stations, AlphaNet) on ethernet port 1.

Default Filters Settings



In the Filters Settings one can modify what services should be available on each ethernet interface.

New TCP or UDP ports can be added by selecting Add Filter. Remember to enable it after adding!

Adding TCP port 4001 to the Filters



Stations/Devices.

From the Stations/Devices list some user parameters can be modified.

The table can be sorted by clicking on the relevant header. In the Search field you can search for any free text, e.g. directory number, display text or IP address.

Stations/Devices


By clicking on a station in the list, the following parameters can be modified:

  • Directory Number
  • Display Text
  • COS (Class of service)
  • Volume
  • Noise Reduction
  • Always Private
Modify station configuration


Changes will take immediate effect. No reset is required.

OBS icon Configuration changes done from the ICX web interface are stored in the ICX-500 Gateway. In order to syncronize AlphaPro with the actual configuration of the ICX Gateway, it is important to perform a GetAll from AlphaPro


Quick Edit Mode

When multiple changes are to be made, the Quick Edit Mode can be enabled, and each parameter can be modified directly from the table without having to open an extra window.

Quick Edlt Mode let you do multiple edits in an easy way



Remember to click on Apply Changes to save the changes.

Logging

There are three different log types:

  • Debug Log: Low level messages. For debugging purposes for software engineers.
  • System Log: Provides log events for monitoring the health of the ICX system. The log includes Station Line errors, restart, backup/restore, Customized event logging (LOG command) etc.
  • Call Statistics Log: Detailed information about Calls, Call Requests, Group calls, external SIP trunk calls

There are four different log Destinations:

  • Local Filesystem - Log files are stored locally on the ICX-500 Gateway. Logs can be viewed or downloaded from System Monitoring > Logs
  • Remote SysLog - Enter the IP Address of the remote computer, and the protocol type (UDP or TCP)
  • E-Mail - If the ICX-500 has access to an e-mail server, log events can be forwarded to a predefined e-mail address
  • SNMP Trap - Enter the IP Address of the remote computer running the SNMP service. Select SNMP System Information to configure additional SNMP parameters (Name, Location, Contact, Community String and SNMP Port).
Log configuration



To configure logging press Edit next to the Destination, and enter relevant parameters. The different logs are enabled by setting "Pri Level" = Info.

Enable logs by setting Pri Level = "Info"


After changed are Saved and Applied, the logging can be tested by clicking on "Generate test log messages".

To filter on a specific text in the log strings, add the required text in the Contains field. Only log events that contain this text will be sent to the log.


Logging to Local Filesystem
The log system is creating a new file every day for each of the log types (Debug, System and Statistics).

Log rotation is used to prevent the logs from growing out of control. Every 10 minutes there is a check if the log files are consuming more than 20MB of memory space. If more than 20MB, the oldest log file will be deleted, until the remaining space is below 20MB. I.e. you will loose one day of logging each time a log file is deleted.

Log Space in Local Filesystem


Clean up will remove 10% of the oldest log content. Delete will delete the complete log file.


Licensing

For how to obtain and install licenses, see Licenses for ICX-500 and ICX-Core.

Installed licenses are displayed in System Configuration > Licensing.

ICX-500 License management page



The ICX system comes with a 20-day free license period. Until valid licenses are installed, the remaining time of the free period is displayed.

Note icon
  • From factory there is a 20-day free license period during which all features can be used without the need of any license.
  • When the free license period expires, there must be a valid license installed, if not the licensed feature or device will cease to operate


License Configuration - Free license period



User Management

From the User Management page the username and password for logging into the ICX can be changed.

User Management Form


For security reasons it is highly recommended to change the default username and password.

Default username/password:

  • Read User: alpha/com
  • Read/Write User: admin/alphaadmin
  • Custom Script User: scripter/alphascript
Note icon

* AlphaPro is using the "Read/Write User" credentials.
* High Availability system (IPHA) is using the "Read/Write User" credentials.



Time and Date

Time and Date Settings


The Time and Date section shows the current time zone configured.

In the Select New Region section a new time zone can be configured. When a valid time zone is configured, the ICX will automatically adjust for daylight saving time.

In the Set Localtime section, the date and time can be manually set.

In the Configure Network Time Protocol (NTP) Server section the ICX can be configured to synchronise the time to a Network Time Protocol (NTP) server. Enter the IP address of the NTP server, then Set Server. The ICX will now check if this is a valid NTP server, and display a message accordingly. The connection to the NTP Server can also be tested by the Test Server button. The button Get Time will instantly read the NTP time and set the time and date.

When the ICX is configured to use NTP Server, the time and date is automatically syncronized once an hour (20 minutes past the hour).

NTP Clock Drift Adjustment: If there is no NTP Server available at site where the ICX500 Gateway is to be installed, there is an option to temporarily connect the ICX to a network with NTP Server during commisioning (e.g. in the workshop before shipping to end customer). Configure the ICX to syncronize the time to this NTP server. Now the internal ICX clock will be compared to the NTP time, and the offset will be calculated. One should leave the ICX connected to the NTP network for at least 24 hours to get the best result. When the ICX is moved to a network without NTP Server, it will use this offset value to correct the real time clock in ICX.

When an offset value has been calculated, the Slew will show a value, and the Update Time will show the date and time when the offset value was stored.


DNS

TBD

Hostnames

TBD

DHCP server

TBD

Messaging

TBD

High Availability

TBD

System Maintenance

System Recovery

  • Small Reset: Reset main applications
  • Reboot: Reboots the system
  • Chilly Restart: Reset main applications and clear state data like mails, transfers, absense, %udd and program selection. Configuration data are kept.
  • Load Factory Default: Reset intercom configuration data. IP settings are kept.
  • Clean & Factory Defaults: Reset intercom configuration data. Remove License, SysLog and Backup files. IP settings are kept.

System Upgrade

TBD

IP Device Upgrade

TBD

Backup and Restore

TBD

Import

TBD

Help

Contains a link to this ZenitelWiki article.