Difference between revisions of "INCA Hotline LED Indicators"
From Zenitel Wiki
(Created page with "====Station LED==== LED4 - Red 5mm LED on board rear side. This LED is on some models visible through the front plate, on others not. File:IP Hotline Station LED.PNG|left|t...") |
(→Station LED) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | == Station LED == | |
LED4 - Red 5mm LED on board rear side. | LED4 - Red 5mm LED on board rear side. | ||
| Line 6: | Line 6: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
'''Blinking at 1 second intervals:'''<br> | '''Blinking at 1 second intervals:'''<br> | ||
| − | Station | + | Station cannot register to the server/controller |
Possible reasons: | Possible reasons: | ||
| − | * | + | * Invalid network settings (IP address and network mask) in the device |
| − | + | * Wrong or missing account settings (Server IP, directory number, password..) | |
| − | * | + | * Failing to register due to missing license in the server |
| − | * | + | * The server is offline |
| − | + | * Network or Server firewall is not blocking port 50001 (ICX-AlphaCom) or 5060 (Edge/SIP) | |
| − | + | If the server is on a different subnet, check that | |
| − | + | * A valid Default gateway is defined | |
| − | |||
| − | |||
| − | * | ||
| − | * | ||
'''No blinking:''' | '''No blinking:''' | ||
Possible reasons: | Possible reasons: | ||
| − | * Station connected and registered to the | + | * Station connected and registered to the server/controller |
* Station not powered up (if no other LEDs are active) | * Station not powered up (if no other LEDs are active) | ||
| − | + | '''Blinking at 5 second intervals:'''<br/> | |
| − | + | {{Note| This LED behaviour only applies in ICX-AlphaCom mode}} | |
| − | + | Station connected but NOT registered in the ICX-AlphaCom | |
| − | |||
| − | '''Blinking | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Possible reasons: | Possible reasons: | ||
| − | * | + | * Station has not been programmed in AlphaPro |
| − | * | + | * Missing IP Station license in ICX-AlphaCom |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | [[Category:Station Indication LEDs]] | |
| − | [[ | ||
| − | |||
| − | |||
| − | |||
Latest revision as of 12:45, 20 November 2020
Station LED
LED4 - Red 5mm LED on board rear side.
This LED is on some models visible through the front plate, on others not.
Blinking at 1 second intervals:
Station cannot register to the server/controller
Possible reasons:
- Invalid network settings (IP address and network mask) in the device
- Wrong or missing account settings (Server IP, directory number, password..)
- Failing to register due to missing license in the server
- The server is offline
- Network or Server firewall is not blocking port 50001 (ICX-AlphaCom) or 5060 (Edge/SIP)
If the server is on a different subnet, check that
- A valid Default gateway is defined
No blinking:
Possible reasons:
- Station connected and registered to the server/controller
- Station not powered up (if no other LEDs are active)
Blinking at 5 second intervals:
|
This LED behaviour only applies in ICX-AlphaCom mode |
Station connected but NOT registered in the ICX-AlphaCom
Possible reasons:
- Station has not been programmed in AlphaPro
- Missing IP Station license in ICX-AlphaCom