IND - Indicator control for CRMIV LEDs, buzzer etc.

The IND (INDication) or GIND action are used in the Event Handler for sending commands to a station or a group of stations. The following stations are supporting the IND command:

• IP Flush Master and CRM V: Control the LED's in the DAK keys
• CRM IV: Control the LED's in the DAK keys, the internal buzzer or relay, and the backlight of the display
• DualDisplay station: Control the video-state of the DAK-display
• Priscom station: Control the outputs used for lamps, cell light, call LED and spare output
• IP-ARIO: Control the Error LED and the Radio LED
• IP Substation: Control relay and spare output
• Turbine station: Control relay and the 6 additional outputs
• ECPIR-3P and EBMDR-8 module

Note: Using the IND command also triggers a ST_STATE message on the OPC port; it is advisable to add two (or possibly more, depending on the system load) PAUSE commands before the IND command, especially when the event trigger is event 7, 8 or 44, When Change To OFF

Command syntax

IND command:

IND <station phys.no> <output> <LED no/buzzer> <Ind-type> [state]

Example: On station 2, key 23, turn green led, fast flashing, ON

IND 2 23 2 3 ON

GIND command:

GIND <group ind> <output> <LED no/buzzer> <Ind-type> [state]

<group ind> is the AlphaCom group index number 1-250. (Not the group directory number)

There must be a space between the command parameters.

Parameter description:

Station/Parameter	phys. number	output	LED no/buzzer	IND-type	[state]
CRM V and IP Flush Master (8024)	1 - 552	1-100 = DAK-key number	1 = Red LED 2 = Green LED	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
IP Substation (8022)	1 - 552	1 = Relay 2 = Spare output	Always "1"	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
Turbine station	1 - 552	17 = Relay 11-16 = Spare outputs See note below!	Always "1"	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
IP-LCM	1 - 552	17 = Relay 11-16 = Spare outputs 27-34 = external relays See note below!	Always "1"	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
ECPIR-3P	1 - 552	1-100 = DAK-key number 513 = Fault LED Requires AMC 13.1.x.x	1 = Red LED 2 = Green LED Always "1"	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
DualDisplay	1 - 552	1-100 = The DAK-key line	Always "1"	Video-state of the DAK-display: 0 = Normal 1 = Inverse 2 = Slow flash 3 = Fast flash	ON or OFF
IP-ARIO	1 - 552	1 = Radio LED 2 = Error LED	1 = Red LED (Radio and Error) 2 = Green LED (Radio LED only)	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
PrisCom	1 - 552	1 - 4 = Lamp outputs 5 - 6 = Spare outputs 7 = Relay (Cell light) 8 = Call LED	Always "1"	1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority)	ON or OFF
CRM IV	1 - 552	1-100 = DAK-key number 1023 = Buzzer 1024 = Display backlight	DAK-key: 1 = Red LED 2 = Green LED Buzzer: 1 = Internal buzzer 2 = External buzzer (relay) Display backlight: 1 = Backlight	DAK LED's: 1 = continuous (low priority) 2 = slow flash (medium priority) 3 = fast flash (high priority) Buzzers: 1 = 1 bleep per 8 seconds (low priority) 2 = 1 bleep per 2 seconds (medium priority) 3 = 4 bleeps per second (high priority) 4 = continuous (alarm priority) Display backlight: 1 = continuous	ON or OFF

The state parameter is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.

Note on Turbine: The output numbers depend on the AMC software version. AMC version 11.2.3.9 and earlier: Use IND numbers 1 - 7 AMC version 11.2.3.10: Outputs cannot be controlled by IND command AMC version 11.2.3.11 and later: Use IND numbers 11 - 17

Related articles

• CRM IV: LED and buzzer control
• CRM IV: Indicate status of remote stations in AlphaNet
• RCO - Remote Control Output
• $SET_IPRCO: This data command can be used to activate Remote Control Outputs on IP Stations and IPARIO without having to define the RCO's in the RCO table.