Difference between revisions of "IP Flush Master DAK-48 Module"

Revision as of 14:29, 8 January 2021

DAK-48 Unit. Item number: 1008010100

The IP DAK-48 unit expands the:

with an additional 48 Direct Access Keys. Up to two DAK-48 units can be connected to one station.

Software and license requirements

Software:

IP Flush Master (INCA): Version 01.09.3.0 or later
IP Flush Master (Turbine): Version 6.0.3.0 or later
AMC-IP: Version 10.60.3.0 or later

License: To enable the use of the DAK48 module a license is required:

1009648001: License for CRM-V DAK expansion

Regardless if the CRM-V station is using one or two DAK48 modules, only one CRM-V DAK expansion license is required.

The DAK-48 module is supported in ICX-AlphaCom mode only, not in Edge, Pulse or SIP mode.

Installing the DAK-48 Expansion module

To interconnect the DAK-48 unit to the main unit, use the cable which is coming with the DAK-48 unit. The DAK-48 unit receive its power and data via this cable.

A standard patch cable (1:1) must not be used. It might damage the unit!

Installing the IP DAK-48 Unit:

Power off the IP Flush Master station by disconnecting the ethernet cable in the LAN port
Plug one end of the cable coming with the DAK-48 unit into the RJ45 port on the right hand side of the IP Flush Master station (when the station is viewed from the front).
Plug the other end of the cable into the left RJ45 port on the DAK-48 unit (when the unit is viewed from the front).
Power up the IP Flush Master station by connecting the ethernet cable to the LAN port

To add a second DAK unit, plug one end of an RJ45-RJ45 cable into the RJ45 port of the installed unit and plug the other end into the RJ45 port of the new unit.

Related products

Label Paper for IP DAK-48 Unit - 1008010101 (20 sheets)

@@ Line 1: / Line 1: @@
- '''Note!''' The license 1009648001 is required to extend the IP Flush Master with the optional IP DAK-48 Unit.
+{{AI}} [[File:1008010100.PNG|thumb|200px|DAK-48 Unit. Item number: 1008010100]]
+The '''IP DAK-48 unit''' expands the:
+* [[IP Flush Master -V2]]
+* [[IP Flush Master - 1008031000|INCA IP Flush Master Station]]
+with an additional 48 Direct Access Keys. Up to two DAK-48 units can be connected to one station.
-[[File:DAK48.jpg|thumb|DAK-48 Unit]]
+==Software and license requirements==
-:* Item number: [[DAK48 module - 1008010100|1008010100]]
+'''Software:'''
-The IP DAK-48 unit expands the IP Flush Master station with an additional 48 Direct Access Keys. This unit can also be used with the IP OR Station and the IP Master Station Kit.
+* IP Flush Master (INCA): Version 01.09.3.0 or later
+* IP Flush Master (Turbine): Version 6.0.3.0 or later
+* AMC-IP: Version 10.60.3.0 or later
- Before installation, disconnect power from the IP Flush Master station
+'''License:'''
+To enable the use of the DAK48 module a license is required:
+* 1009648001: [[Licenses#CRM-V_DAK_expansion|License for CRM-V DAK expansion]]
-The accompanying RJ45-RJ45 cable is used to install the DAK unit on an IP Flush Master station. This cable has an RJ45 plug at both ends. The two ends are interchangeable. Up to two DAK units can be installed per station. Each DAK unit has two RJ45 ports, one located on the left side and one on the right side.
+Regardless if the CRM-V station is using one or two DAK48 modules, only one CRM-V DAK expansion license is required.
+{{note|The DAK-48 module is supported in '''ICX-AlphaCom mode''' only, not in Edge, Pulse or SIP mode.}}
-<u>'''To install the IP DAK-48 Unit:'''</u><br/>
+== Installing the DAK-48 Expansion module ==
-* Plug one end of the RJ45-RJ45 cable into the RJ45 port on the right of the station (when the station is viewed from the front).
+To interconnect the DAK-48 unit to the main unit, use the cable which is coming with the DAK-48 unit. The DAK-48 unit receive its power and data via this cable.
-* Plug the other end of the RJ45-RJ45 cable into the left (when the unit is viewed from the front) RJ45 port on the DAK unit.
-[[File:IP_Master_DAK-48_Unit_Installation.PNG]]<br/>
+{{obs| A standard patch cable (1:1) must not be used. It might damage the unit!}}
-Installing the IP DAK-48 Unit
- To add another DAK unit, plug one end of an RJ45-RJ45 cable into the RJ45 port of
+Installing the IP DAK-48 Unit:
- the installed unit and plug the other end into the RJ45 port of the new unit.
+* Power off the IP Flush Master station by disconnecting the ethernet cable in the LAN port
+* Plug one end of the cable coming with the DAK-48 unit into the RJ45 port on the right hand side of the IP Flush Master station (when the station is viewed from the front).
+* Plug the other end of the cable into the left RJ45 port on the DAK-48 unit (when the unit is viewed from the front).
+* Power up the IP Flush Master station by connecting the ethernet cable to the LAN port
+[[File:IP_Master_DAK-48_Unit_Installation.PNG]]
+To add a second DAK unit, plug one end of an RJ45-RJ45 cable into the RJ45 port of the installed unit and plug the other end into the RJ45 port of the new unit.
 <br style="clear:both;" />
-===<u>Related article</u>===
+==Related articles==
-* [[Licenses#CRM-V_DAK_expansion|DAK expansion license]]
+* [[DAK-48 Module Dimensions & Mounting Instructions|Dimensions]]
+* [[Back box on wall mount - 1008098600]]
+* [[Back box flush mount - 1008098700]]
+* [[Licenses#CRM-V_DAK_expansion|AlphaCom DAK expansion license 1009648001]]
+* [[Licenses for ICX-500 and ICX-AlphaCom Core]]
+* [http://www.zenitel.com/product/crm-v-dak48 Additional Documentation on Zenitel.com]
+==Related products ==
+* Label Paper for IP DAK-48 Unit - 1008010101 (20 sheets)
 [[Category: INCA Backboxes and accessories]]
+[[Category: Turbine Backboxes and accessories]]

Difference between revisions of "IP Flush Master DAK-48 Module"

From Zenitel Wiki

Revision as of 14:29, 8 January 2021

Contents

Software and license requirements

Installing the DAK-48 Expansion module

Related articles

Related products