Actions

Difference between revisions of "IP Flush Master Station LED Indications"

From Zenitel Wiki

 
(4 intermediate revisions by the same user not shown)
Line 3: Line 3:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
 
'''Blinking at 1 second intervals:'''<br/>
 
'''Blinking at 1 second intervals:'''<br/>
Station has no connection to the AlphaCom XE Audio Server.
+
Station cannot register to the server/controller
  
 
Possible reasons:
 
Possible reasons:
* No connection to Ethernet
+
* Invalid network settings (IP address and network mask) in the device
* Wrong AlphaCom IP address configured
+
* Wrong or missing account settings (Server IP, directory number, password..)
* Invalid IP address
+
* Failing to register due to missing license in the server
* No gateway or wrong gateway to the AlphaCom XE Audio Server
+
* The server is offline
 
+
* Network or Server firewall is not blocking port 50001 (ICX-AlphaCom) or 5060 (Edge/SIP)
'''Blinking at 5 second intervals:'''<br/>
+
If the server is on a different subnet, check that
Station connected but NOT registered in the AlphaCom XE Audio Server.
+
* A valid Default gateway is defined
 
 
Possible reasons:
 
* Station has not been programmed in AlphaPro
 
* Missing IP Station license in AlphaCom XE Audio Server
 
  
 
'''No blinking:'''
 
'''No blinking:'''
  
 
Possible reasons:  
 
Possible reasons:  
* Station connected and registered to the AlphaCom XE Audio Server
+
* Station connected and registered to the ICX-AlphaCom
 
* Station not powered up (if no other LEDs are active)
 
* Station not powered up (if no other LEDs are active)
  
== Status LED ==
+
'''Blinking at 5 second intervals:'''<br/>
LED3 – Bicolor SMD LED on board component side.
+
{{Note| This LED behaviour only applies to INCA Desktop stations [[IP Flush Master - 1008031000|1008031000]] and [[IP OR Master Station - 1008015000|1008015000]] in ICX-AlphaCom mode}}
[[File:MasterStationKit Indications1.png|left|thumb|400px|Status LED]]
+
Station connected but NOT registered in the ICX-AlphaCom
<br style="clear:both;" />
 
'''Blinking 2 red + 1 green:'''<br>
 
* Station has no connection to the AlphaCom XE Audio Server.
 
  
'''Blinking 1 red + 2 green:'''<br>
 
* Station connected but NOT registered in the AlphaCom XE Audio Server.
 
 
'''Blinking 3 green:'''
 
* Station connected and registered in the AlphaCom XE Audio Server.
 
 
== Power LED ==
 
LED6 – Yellow SMD LED on board component side.
 
[[File:MasterStationKit Indications2.png|left|thumb|400px|Power LED]]
 
<br style="clear:both;" />
 
* Light:  13VDC board power OK.
 
* No light:  13VDC board power faulty if no other LEDs are lit.
 
 
 
Possible reasons:  
 
Possible reasons:  
* 24 VDC or PoE not connected
+
* Station has not been programmed in AlphaPro
* Faulty board
+
* Missing IP Station license in ICX-AlphaCom
 
 
== LAN LEDs ==
 
'''Left LED:'''<br>
 
[[File:IP Master Indications 4.PNG|left|thumb|200px|Left LED]]
 
<br style="clear:both;" />
 
* Steady light:  Ethernet connection OK
 
* Blinking:    Ethernet traffic
 
* No light:    No Ethernet connection
 
 
 
'''Right LED:'''<br>
 
[[File:IP Master Indications 5.PNG|left|thumb|200px|Right LED]]
 
<br style="clear:both;" />
 
* Light:    100 Mbit Ethernet connection
 
* No light:  10 Mbit Ethernet connection
 
  
[[Category:INCA Indication LEDs]]
+
[[Category:Station Indication LEDs]]

Latest revision as of 11:24, 20 November 2020

Station LED

Station LED


Blinking at 1 second intervals:
Station cannot register to the server/controller

Possible reasons:

  • Invalid network settings (IP address and network mask) in the device
  • Wrong or missing account settings (Server IP, directory number, password..)
  • Failing to register due to missing license in the server
  • The server is offline
  • Network or Server firewall is not blocking port 50001 (ICX-AlphaCom) or 5060 (Edge/SIP)

If the server is on a different subnet, check that

  • A valid Default gateway is defined

No blinking:

Possible reasons:

  • Station connected and registered to the ICX-AlphaCom
  • Station not powered up (if no other LEDs are active)

Blinking at 5 second intervals:

Note icon This LED behaviour only applies to INCA Desktop stations 1008031000 and 1008015000 in ICX-AlphaCom mode


Station connected but NOT registered in the ICX-AlphaCom

Possible reasons:

  • Station has not been programmed in AlphaPro
  • Missing IP Station license in ICX-AlphaCom