Actions

Philips M100

From Zenitel Wiki

Revision as of 11:09, 16 March 2012 by Roarl (talk) (→‎Setting system parameters)

Software Requirements

AlphaCom

The AMC-IP board must have software version 10.20 or higher. Latest software version is always recommended. The latest version for AlphaCom can be downloaded here.
The AMC-IP software includes the following software routines:

  • The software daemon (M100d) which is running the M100 format with the AlphaCom XE main software.
  • The software daemon AMCd which is running the AlphaCom XE Main Software
  • The embedded web server which is used to configure AMCd and M100d (AlphaWeb).

M100

The software type and version is not critical as long as it supports 6-digit dialling.
Supported SW: 

6U Computer Card LBB 7103/07: SW LBB 7216/83
3U Computer Card LBB 7103/06: SW LBB 7216/83
FC Card LBB 7110/13:          SW LBB 7202/28

Programming Tools

AlphaCom

The programming tool for AlphaCom is AlphaPro software version 10.28 or higher.
Download the latest version here.
AlphaPro is used to identify M100 modules as nodes in the AlphaNet and to configure the AGA audio routing.

M100

The programming tool for M100 is SysMain software version 3.0. It is available on request from alphasupport@zenitel.com.

Audio Link Interface

M100Int 1.PNG
The Audio Link Interface Unit is powered from the M100 module. Solder a 3-wire power cable to the three solder studs labeled +5V, 0V (GND), and -5V on the M100 backplane. Connect the other free end of the cable to a 3-way plug-in screw terminal that connects to the receptor labeled -5V GND +5V at the back of the Audio Link Interface Unit.
M100Int 2.PNG

Data Connection

AlphaCom

Use a crossed RS232 cable with female 9-pin D-sub connectors at each end to connect the AlphaCom XE7 serial Port 0 to the Audio Link Interface connector labeled AlphaCom RS232.

M100

The M100 system communicates via optical fiber cables. The opto cable (LBB 7103/61) connects from the M100 Computer Card (LBB 7103/05) to the Audio Link Interface Unit. On the Computer Card, connect the opto cable to the connector labeled Module 1 (assuming that the M100 is a single-module system). The other end of the opto cable connects to the receptors labeled M100 Serial - Opto at the back of the Audio Link Interface Unit.
M100Int 3.PNG

Audio Connection

AlphaCom

M100Int 6.PNG

Group Call & 8 Audio Channels

Table 1

To connect 8-channel Group Call audio for AlphaCom:

  • Cut off one connector on three 8-pair flat cables.
  • Connect the free ends to nine 4-way plug-in screw terminals according to table 1.
  • Connect the plugs to the corresponding connectors at the back of the AlphaCom XE7 Audio Server according to table 1.
  • Connect the other end of the cables to the connectors at the back of the Audio Link Interface labeled AlphaCom Audio 1 to 3.

M100Int 4.PNG

Group Call & 16 Audio Channels

Table 2

To connect 16-channel Group Call audio for AlphaCom:

  • Cut off one connector on six 8-pair flat cables.
  • Connect the free ends to seventeen 4-way plug-in screw terminals according to tables 1 and 2.
  • Connect the plugs to the corresponding connectors at the back of the AlphaCom XE7 Audio Server according to tables 1 and 2.
  • Connect the other end of the cables to the connectors at the back of the Audio Link Interface labeled AlphaCom Audio 1 to 6.

M100Int 5.PNG

M100

Group Call

To connect Group Call audio for M100:

  • Connect a 20-core ribbon cable to the free connector labeled PGM at the back of the M100 module.
    • Only the Group Call channel is transmitted and not the Program Distribution channels.
  • Connect the other end to the connector at the back of the Audio Link Interface labeled M100 Group Call.

8 audio channels - 1 LUS board

To connect 8-channel audio for M100:

  • Connect a 32-core ribbon cable to the free connector labeled LU8-9 at the back of the M100 module.
  • Connect the other end to the connector at the back of the Audio Link Interface labeled M100 LU9 & LU8.

16 audio channels - 2 LUS boards

To connect 16-channel audio for M100:

  • Connect a 16-core ribbon cable to the free connector labeled LUS/LU9 at the back of the M100 module.
  • Connect the other end to the connector at the back of the Audio Link Interface labeled M100 LU9.

M100Int 7.PNG

Programming in SysMain (M100)

Installation

Install and start SysMain on your PC.

Getting Started for New M100 System

  • Select File -> New
    • A setup wizard will start
  • Click Next

M100Int 10.PNG

  • Select S-72 Stand-alone Exchange and click Next

M100Int 11.PNG

  • Select the type of system of your choice. In this example Hospital System is selected.
  • Click Next

M100Int 12.PNG

  • Select Use default tables and click OK

Setting system parameters

After setup is completed, the Update system information window automatically opens:
M100Int 13.PNG

  • Set No. of modules to 2.
  • Select the number of LUS cards installed.
  • Click OK

Updating the exchange

In the menu, click Exchange and select Send data to the exchange M100Int 14.PNG

  • Select Module 0
  • Enable Number list and System parameters
  • Click Send

Adding new module to existing M100 exchange

When there is an existing M100 exchange with modules that are already defined, a new module has to be added before connecting to the Audio Link Interface. In the Update system information window in SysMain, activate a new module by increasing the number of existing modules by one: M100Int 15.PNG
The opto cable connects to the first available output. If no outputs are available, an ACIA card (LBB 7103/56) has to be installed. The ACIA card requires that the exchange is already fitted with the Computer Card (LBB 7103/05).
See M100 documentation for further details.

Retrieved from "https://wiki.zenitel.com/w/index.php?title=Philips_M100&oldid=115195"