Actions

Difference between revisions of "SNMP in IP Stations"

From Zenitel Wiki

m
 
(35 intermediate revisions by 5 users not shown)
Line 1: Line 1:
{{S}}
+
{{AEIPS}}
Stentofon IP devices ([[:Category:INCA Stations|INCA stations]], [[:Category:Turbine|Turbine stations]], [[:Category:Public Address - Network amplifiers|ENA Amplifiers]]) run a SNMP service and support SNMP polling and SNMP traps.   
+
Zenitel IP devices run a SNMP service and support SNMP polling and SNMP traps.   
  
  
Line 11: Line 11:
  
 
==SNMP Configuration==
 
==SNMP Configuration==
SNMP can be configured from the station web (Advanced Network > SNMP).   
+
SNMP is configured from the station web: '''Advanced Network''' > '''SNMP'''.   
  
For INCA stations, you need to set the station in SIP mode, enable SNMP, and set it back to AlphaCom mode. When INCA station operates in AlphaCom mode the SNMP service is still running, but only generic built in MIBs are supported.
+
[[File:SNMP1.png|thumb|left|700px|SNMP Configuration]]
 +
<br style="clear:both;" />
  
For ENA Amplifiers and Turbine Stations, after '''upgrade from 4.9 or older SW to 4.10 or newer SW''', '''SNMP configuration is retained''', but when downgrading from 4.10 or newer SW to lower SW version than 4.10, SNMP needs to be reconfigured (factory reset recommended).
+
'''SNMP Settings'''  
  
{{Note|Not all fields are available on INCA stations}}
+
*'''Access''': read or none are available, setting none will disable SNMP
 +
*'''SNMP v1/v2c''': selects SNMP version used, '''one or both need to be selected for SNMP to work'''
 +
*'''Community string''': string used as password for authentication. Use alphanumeric characters. As from firmware 8.1.3.0 also special characters ''':$#@_?!,-.*'''' are allowed.
 +
*'''Allowed Network''': this is used, together with the network mask, to determine the allowed network for reading the MIB on the station. The IP address is entered in regular dot notation, e.g. 10.5.2.100. For example with an allowed network 10.5.2.0 and a network mask of 24, any station with an IP address in the range 10.5.2.0 to 10.5.2.255 can access the MIB. Setting '''0.0.0.0/0''' will allow all
 +
*'''Name''': SNMP name string (sent as sysName OID in traps)
 +
*'''Location''': SNMP Location string
 +
*'''Contact''': SNMP Contact string
  
[[File:Snmp web conf.png]]
+
'''SNMP Trap and Informs Settings'''
 +
 
 +
*Traps/informs receiving server address can be set here
 +
*If left blank it will disable sending traps/informs
  
'''SNMP Settings'''
 
* access: read or none are available, setting none will disable SNMP
 
* SNMP v1/v2c: selects SNMP version used, '''one or both need to be selected for SNMP to work'''
 
* Community string: string used as password for authentication
 
* Allowed network: this is used, together with the network mask, to determine the allowed network for reading the MIB on the station. The IP address is entered in regular dot notation, e.g. 10.5.2.100. For example with an allowed network 10.5.2.0 and a network mask of 24, any station with an IP address in the range 10.5.2.0 to 10.5.2.255 can access the MIB. Setting '''0.0.0.0/0''' will allow all
 
* Name: SNMP name string (sent as sysName OID in traps)
 
* Location SNMP Location string
 
* Contact: SNMP Contact string
 
'''SNMP Trap and Informs Settings'''
 
* Traps/informs receiving server address can be set here
 
* If left blank it will disable sending traps/informs
 
 
'''SNMP Custom Configuration File'''
 
'''SNMP Custom Configuration File'''
* Custom '''snmpd.conf''' file can be uploaded and used on the device
+
 
* File is kept during device SW upgrades
+
*Custom '''snmpd.conf''' file can be uploaded and used on the device
* File syntax and content are not checked and if errors are present in the file it can render SNMP inoperative
+
*File is kept during device SW upgrades
* When custom file is uploaded SNMP Settings are unavailable
+
*File syntax and content are not checked and if errors are present in the file it can render SNMP inoperative
* File can be viewed or downloaded
+
*When custom file is uploaded SNMP Settings are unavailable
* New file can be uploaded at any time
+
*File can be viewed or downloaded
* When custom file is deleted device will revert back to configuration defined in web config
+
*New file can be uploaded at any time
 +
*When custom file is deleted, the device will revert back to configuration defined in web config
 +
 
 
'''Enable SNMP Traps'''
 
'''Enable SNMP Traps'''
* Available traps (notifications) depend on device type and mode
 
* If specific event occurs and corresponding SNMP Trap is enabled, notification (trap) will be generated and sent to trap/inform receiver IP address
 
* [[SNMP in IP Stations#Alarm/Fault Notifications (Traps)|Traps descriptions]]
 
  
=== Custom Faults ===
+
*Available traps (notifications) depend on device type and mode
Custom faults are available only on amplifiers in SIP/Pulse or Exigo (configurable through EMT) mode. When RCI is triggered device will send SNMP Trap with custom fault description and priority.
+
*If specific event occurs and corresponding SNMP Trap is enabled, notification (trap) will be generated and sent to trap/inform receiver IP address
 +
*[[SNMP in IP Stations#Alarm/Fault Notifications (Traps)|Traps descriptions]]
  
Configuration for faults is available in web Amplifier Settings -> RCO/RCI Config (or IO Monitoring). For custom faults to be sent traps have to be enabled in config (Advanced Network → SNMP → Enable SNMP Traps → Custom Fault){{Note|Available only on ENA amplifiers}}
+
===Custom Faults===
 +
Custom faults are available only on [[:category:Public Address - Network amplifiers|ENA amplifiers]] in Edge/SIP/Pulse or Exigo (configurable through EMT) mode. When RCI is triggered, the device will send SNMP Trap with custom fault description and priority.
 +
 
 +
Configuration for faults is available in web Amplifier Settings -> RCO/RCI Config (or IO Monitoring). For custom faults to be sent traps have to be enabled in config (Advanced Network → SNMP → Enable SNMP Traps → Custom Fault){{Note|Available only on [[:category:Public Address - Network amplifiers|ENA amplifiers]]}}
  
 
[[File:Custom faults.png]]
 
[[File:Custom faults.png]]
  
== Object Identifier (OID) Numbers ==
+
==Object Identifier (OID) Numbers==
 
Zenitel Norway AS OID is 26122 (stentofon) → 1.3.6.1.4.1.26122
 
Zenitel Norway AS OID is 26122 (stentofon) → 1.3.6.1.4.1.26122
  
=== Overview ===
+
===Overview===
 
{| class="wikitable"
 
{| class="wikitable"
 
!'''Name'''
 
!'''Name'''
Line 136: Line 138:
 
|}
 
|}
  
=== ipstation scalar and tabular objects ===
+
<br><br>
 +
 
 +
===ipstation scalar and tabular objects===
 
{| class="wikitable mw-collapsible"
 
{| class="wikitable mw-collapsible"
 
!'''Name'''
 
!'''Name'''
Line 269: Line 273:
 
|}
 
|}
  
=== vsDevice scalar and tabular objects ===
+
<br><br>
 +
 
 +
===vsDevice scalar and tabular objects===
 
{| class="wikitable mw-collapsible"
 
{| class="wikitable mw-collapsible"
 
!'''Name'''
 
!'''Name'''
Line 284: Line 290:
 
|1.3.6.1.4.1.26122.3.1.'''1'''
 
|1.3.6.1.4.1.26122.3.1.'''1'''
 
|DisplayString(SIZE(128))
 
|DisplayString(SIZE(128))
|"The device Package Version
+
|The device Package Version
 
|-
 
|-
 
|infoModelType
 
|infoModelType
Line 822: Line 828:
 
|}
 
|}
  
=== Notifications (traps) ===
+
<br><br>
  
==== Alarm Objects ====
+
===Notifications (traps)===
 +
 
 +
====Alarm Objects====
 
Each notification (trap) contains Alarm object with following fields
 
Each notification (trap) contains Alarm object with following fields
 
{| class="wikitable"
 
{| class="wikitable"
Line 868: Line 876:
 
|}
 
|}
  
==== Alarm/Fault Notifications (Traps) ====
+
====Alarm/Fault Notifications (Traps)====
Availability dependent on device mode (Sip, Pulse, Alphacom...) and device type and model
+
Availability dependent on device mode (ICX/AlphaCom, Edge, SIP, Pulse...) and device type and model
 
{| class="wikitable mw-collapsible"
 
{| class="wikitable mw-collapsible"
 
!'''Name'''
 
!'''Name'''
Line 877: Line 885:
 
!'''alarmNotifications'''
 
!'''alarmNotifications'''
 
!1.3.6.1.4.1.26122.2.'''5'''
 
!1.3.6.1.4.1.26122.2.'''5'''
!NOTE: Available only in SIP/Pulse mode
+
!NOTE: Available only in Edge/SIP/Pulse mode
 
|-
 
|-
 
|ipsStarted
 
|ipsStarted
Line 997: Line 1,005:
 
|dcPowerFault
 
|dcPowerFault
 
|1.3.6.1.4.1.26122.2.8.'''13'''
 
|1.3.6.1.4.1.26122.2.8.'''13'''
|Reported only if DC Power monitoring enabled. AC power disconnected
+
|Reported only if DC Power monitoring enabled. DC power disconnected
 
|-
 
|-
 
|acPowerFault
 
|acPowerFault
Line 1,028: Line 1,036:
 
|}
 
|}
  
=== Compliance and groups ===
+
====Some example trap descriptions====
 +
{| class="wikitable"
 +
|+
 +
!'''Name'''
 +
!'''Trap description'''
 +
|-
 +
|ethPortDisconnected
 +
|''community=public, enterprise=1.3.6.1.4.1.26122.2.8.15, uptime=7770, agent_ip=10.9.6.223, version=Ver2, 1.3.6.1.4.1.26122.2.4.1.0="Stentofon IPStation", 1.3.6.1.4.1.26122.2.4.2.0=zenitel0c0c2a, sysName=Amplifier, 1.3.6.1.4.1.26122.2.4.3.0=1, 1.3.6.1.4.1.26122.2.4.4.0="Mon Oct 11 12.22.22 2021''
 +
''", 1.3.6.1.4.1.26122.2.4.5.0="Ethernet Port 2 disconnected"''
 +
|-
 +
|tempFault
 +
|''community=public, enterprise=1.3.6.1.4.1.26122.2.8.19, uptime=122149, agent_ip=10.9.6.120, version=Ver2, 1.3.6.1.4.1.26122.2.4.1.0="Stentofon IPStation", 1.3.6.1.4.1.26122.2.4.2.0=zenitel0c0c2b, sysName=Amplifier, 1.3.6.1.4.1.26122.2.4.3.0=4, 1.3.6.1.4.1.26122.2.4.4.0="Thu Sep  9 07.38.24 2021''
 +
''", 1.3.6.1.4.1.26122.2.4.5.0="Temp Sensor Main board, Warning High, measured 65.5C, limit 65.0C"''
 +
|-
 +
|psuVoltageFault
 +
|''community=public, enterprise=1.3.6.1.4.1.26122.2.8.3, uptime=2199, agent_ip=10.9.6.223, version=Ver2, 1.3.6.1.4.1.26122.2.4.1.0="Stentofon IPStation", 1.3.6.1.4.1.26122.2.4.2.0=zenitel0c0c2a, sysName=Amplifier, 1.3.6.1.4.1.26122.2.4.3.0=2, 1.3.6.1.4.1.26122.2.4.4.0="Tue Oct 12 06.59.52 2021''
 +
''", 1.3.6.1.4.1.26122.2.4.5.0="Internal Power 50.00  too low_alert, measured 39.80V, limit 45.00V"''
 +
|}
 +
 
 +
===Compliance and groups===
  
==== Compliance ====
+
====Compliance====
 
{| class="wikitable"
 
{| class="wikitable"
 
!'''Name'''
 
!'''Name'''
Line 1,042: Line 1,069:
 
|'''Mandatory Groups'''
 
|'''Mandatory Groups'''
 
|
 
|
|alarmObjectsGroup
+
|alarmObjectsGroup, sipNotificationsGroup, faultNotificationsGroup, deviceInfoGroup, sipGeneralGroup
sipNotificationsGroup
 
 
 
faultNotificationsGroup
 
 
 
deviceInfoGroup
 
 
 
sipGeneralGroup
 
 
|-
 
|-
 
|'''Optional Groups'''
 
|'''Optional Groups'''
 
|
 
|
|sipRegistrationGroup
+
|sipRegistrationGroup, sipCallGroup, deviceStatusGroup, audioInputsGroup, controlIOGroup, ethernetGroup, amplifierGroup, letsGroup
sipCallGroup
 
 
 
deviceStatusGroup
 
 
 
audioInputsGroup
 
 
 
controlIOGroup
 
 
 
ethernetGroup
 
 
 
amplifierGroup
 
 
 
letsGroup
 
 
|}
 
|}
  
==== Groups ====
+
====Groups====
 
{| class="wikitable mw-collapsible"
 
{| class="wikitable mw-collapsible"
 
!'''Name'''
 
!'''Name'''
Line 1,083: Line 1,090:
 
|sipRegistrationGroup
 
|sipRegistrationGroup
 
|1.3.6.1.4.1.26122.4.2.'''1'''
 
|1.3.6.1.4.1.26122.4.2.'''1'''
|serverType
+
|serverType, serverAddress, isRegistered, lastRegistration
serverAddress
+
|A collection of registration related objects, available only when device is in Edge/SIP/Pulse mode"
 
 
isRegistered
 
 
 
lastRegistration
 
|A collection of registration related objects, available only when device is in SIP/Pulse mode"
 
 
|-
 
|-
 
|sipCallGroup
 
|sipCallGroup
 
|1.3.6.1.4.1.26122.4.2.'''2'''
 
|1.3.6.1.4.1.26122.4.2.'''2'''
|callState
+
|callState, callRemoteId, incomingCallAttempts, incomingCallsSuccess, incomingCallsFailed, outgoingCallAttempts, outgoingCallsSuccess, outgoingCallsFailed
callRemoteId
+
|A collection of call state related objects, available only when device is in Edge/SIP/Pulse mode
 
 
incomingCallAttempts
 
 
 
incomingCallsSuccess
 
 
 
incomingCallsFailed
 
 
 
outgoingCallAttempts
 
 
 
outgoingCallsSuccess
 
 
 
outgoingCallsFailed
 
|A collection of call state related objects, available only when device is in SIP/Pulse mode
 
 
|-
 
|-
 
|sipGeneralGroup
 
|sipGeneralGroup
 
|1.3.6.1.4.1.26122.4.2.'''3'''
 
|1.3.6.1.4.1.26122.4.2.'''3'''
|softwareVersion
+
|softwareVersion, buttonHangingStatus, buttonHangingCounter, soundTestLastResult, soundTestFailedCounter, soundTestErrorCounter, soundTestSuccessCounter
buttonHangingStatus
+
|A collection of general device info objects available only when device is in Edge/SIP/Pulse mode
 
 
buttonHangingCounter
 
 
 
soundTestLastResult
 
 
 
soundTestFailedCounter
 
 
 
soundTestErrorCounter
 
 
 
soundTestSuccessCounter
 
|A collection of general device info objects available only when device is in SIP/Pulse mode
 
 
|-
 
|-
 
|alarmObjectsGroup
 
|alarmObjectsGroup
 
|1.3.6.1.4.1.26122.4.2.'''4'''
 
|1.3.6.1.4.1.26122.4.2.'''4'''
|managedObjectClass
+
|managedObjectClass, managedObjectInstance, severity, time, description
managedObjectInstance
 
 
 
severity
 
 
 
time
 
 
 
description
 
 
|A collection of objects included in all notifications
 
|A collection of objects included in all notifications
 
|-
 
|-
 
|sipNotificationsGroup
 
|sipNotificationsGroup
 
|1.3.6.1.4.1.26122.4.2.'''5'''
 
|1.3.6.1.4.1.26122.4.2.'''5'''
|ipsStarted
+
|ipsStarted, ipsShutdown, sipRegistered, sipUnregistered, sipRegisterFailed, callConnect, callConnectFailed, callDisconnect, callAbnormalDisconnect, soundTestSuccess, soundTestFailed, soundTestError, buttonHanging, buttonPressed, buttonReleased, relayActivated, relayDeactivated, dakPressed, dakReleased
ipsShutdown
+
|A collection of notifications available only when device is in Edge/SIP/Pulse mode and dependent on device type and model
 
 
sipRegistered
 
 
 
sipUnregistered
 
 
 
sipRegisterFailed
 
 
 
callConnect
 
 
 
callConnectFailed
 
 
 
callDisconnect
 
 
 
callAbnormalDisconnect
 
 
 
soundTestSuccess
 
 
 
soundTestFailed
 
 
 
soundTestError
 
 
 
buttonHanging
 
 
 
buttonPressed
 
 
 
buttonReleased
 
 
 
relayActivated
 
 
 
relayDeactivated
 
 
 
dakPressed
 
 
 
dakReleased
 
|A collection of notifications available only when device is in SIP/Pulse mode and dependent on device type and model
 
 
|-
 
|-
 
|faultNotificationsGroup
 
|faultNotificationsGroup
 
|1.3.6.1.4.1.26122.4.2.'''6'''
 
|1.3.6.1.4.1.26122.4.2.'''6'''
|coolingFanFault
+
|coolingFanFault, missingAmpModule, psuVoltageFault, lineVoltageFault, letFault, ampShutdown, slmFault, fuseBroken, ampDisabled, lineInFault, rcoFault, rciFault, dcPowerFault, acPowerFault, ethPortDisconnected, micFault, missingEmbdr, swFault, tempFault, customFault
missingAmpModule
 
 
 
psuVoltageFault
 
 
 
lineVoltageFault
 
 
 
letFault
 
 
 
ampShutdown
 
 
 
slmFault
 
 
 
fuseBroken
 
 
 
ampDisabled
 
 
 
lineInFault
 
 
 
rcoFault
 
 
 
rciFault
 
 
 
dcPowerFault
 
 
 
acPowerFault
 
 
 
ethPortDisconnected
 
 
 
micFault
 
 
 
missingEmbdr
 
 
 
swFault
 
 
 
tempFault
 
 
 
customFault
 
 
|A collection of fault monitoring related notifications, availability based on device type and model
 
|A collection of fault monitoring related notifications, availability based on device type and model
 
|-
 
|-
 
|deviceInfoGroup
 
|deviceInfoGroup
 
|1.3.6.1.4.1.26122.4.2.'''7'''
 
|1.3.6.1.4.1.26122.4.2.'''7'''
|infoPackageVersion
+
|infoPackageVersion, infoModelType, infoModelNumber, infoAmplifierType, infoKernelVersion, infoDeviceTreeVersion, infoDisablement
 
 
infoModelType
 
 
 
infoModelNumber
 
 
 
infoAmplifierType
 
 
 
infoKernelVersion
 
 
 
infoDeviceTreeVersion
 
 
 
infoDisablement
 
 
|A collection of device info objects, some fields not available on all device  types
 
|A collection of device info objects, some fields not available on all device  types
 
|-
 
|-
 
|deviceStatusGroup
 
|deviceStatusGroup
 
|1.3.6.1.4.1.26122.4.2.'''8'''
 
|1.3.6.1.4.1.26122.4.2.'''8'''
|tempTableCount
+
|tempTableCount, tempSensorName, tempCurrentString, tempCurrentValue, tempPeakString, tempPeakValue, tempAverageString, tempAverageValue, fanTableCount, fanString, fanValue, voltageTableCount, voltageString, voltageValue, powerType, powerString, powerMonitoring, powerStatus
 
 
tempSensorName
 
 
 
tempCurrentString
 
 
 
tempCurrentValue
 
 
 
tempPeakString
 
 
 
tempPeakValue
 
 
 
tempAverageString
 
 
 
tempAverageValue
 
 
 
fanTableCount
 
 
 
fanString
 
 
 
fanValue
 
 
 
voltageTableCount
 
 
 
voltageString
 
 
 
voltageValue
 
 
 
powerType
 
 
 
powerString
 
 
 
powerMonitoring
 
 
 
powerStatus
 
 
|A collection of device temperature, fan speed, internal voltages and power  status objects, available on amplifier devices
 
|A collection of device temperature, fan speed, internal voltages and power  status objects, available on amplifier devices
 
|-
 
|-
 
|audioInputsGroup
 
|audioInputsGroup
 
|1.3.6.1.4.1.26122.4.2.'''9'''
 
|1.3.6.1.4.1.26122.4.2.'''9'''
|lineInMonitoringState
+
|lineInMonitoringState, lineInType, lineInString, lineInStatus
 
 
lineInType
 
 
 
lineInString
 
 
 
lineInStatus
 
 
|A collection of audio inputs device objects, available only on devices with microphone or line in monitoring
 
|A collection of audio inputs device objects, available only on devices with microphone or line in monitoring
 
|-
 
|-
 
|controlIOGroup
 
|controlIOGroup
 
|1.3.6.1.4.1.26122.4.2.'''10'''
 
|1.3.6.1.4.1.26122.4.2.'''10'''
|controlInputCount
+
|controlInputCount, controlInputString, controlInputStatus, controlInputMonitored, controlOutputCount, controlOutputString, controlOutputStatus, relayString, relayIdleMode, relayDelay, relayState
 
 
controlInputString
 
 
 
controlInputStatus
 
 
 
controlInputMonitored
 
 
 
controlOutputCount
 
 
 
controlOutputString
 
 
 
controlOutputStatus
 
 
 
relayString
 
 
 
relayIdleMode
 
 
 
relayDelay
 
 
 
relayState
 
 
|A collection of control input and control output (CIO) device objects, available only on devices with CIO monitoring
 
|A collection of control input and control output (CIO) device objects, available only on devices with CIO monitoring
 
|-
 
|-
 
|ethernetGroup
 
|ethernetGroup
 
|1.3.6.1.4.1.26122.4.2.'''11'''
 
|1.3.6.1.4.1.26122.4.2.'''11'''
|ethMonitoringString
+
|ethMonitoringString, ethMonitoringState
 
 
ethMonitoringState
 
 
|A collection of Ethernet switch monitoring objects, available on devices with Ethernet switch
 
|A collection of Ethernet switch monitoring objects, available on devices with Ethernet switch
 
|-
 
|-
 
|amplifierGroup
 
|amplifierGroup
 
|1.3.6.1.4.1.26122.4.2.'''12'''
 
|1.3.6.1.4.1.26122.4.2.'''12'''
|ampChannelCount
+
|ampChannelCount, ampType, ampChannelString, ampChannelStatus, ampChannelMonitorStatus
 
 
ampType
 
 
 
ampChannelString
 
 
 
ampChannelStatus
 
 
 
ampChannelMonitorStatus
 
 
|A collection of amplifier info objects
 
|A collection of amplifier info objects
 
|-
 
|-
 
|letsGroup
 
|letsGroup
 
|1.3.6.1.4.1.26122.4.2.'''13'''
 
|1.3.6.1.4.1.26122.4.2.'''13'''
|letChannel1Count
+
|letChannel1Count, letChannel1Description, letChannel1OperativeStatus, letChannel1SoftwareVersion, letChannel1HardwareVersion, letChannel1Voltage, letChannel2Count, letChannel2Description, letChannel2OperativeStatus, letChannel2SoftwareVersion, letChannel2HardwareVersion, letChannel2Voltage
 
 
letChannel1Description
 
 
 
letChannel1OperativeStatus
 
 
 
letChannel1SoftwareVersion
 
 
 
letChannel1HardwareVersion
 
 
 
letChannel1Voltage
 
 
 
letChannel2Count
 
 
 
letChannel2Description
 
 
 
letChannel2OperativeStatus
 
 
 
letChannel2SoftwareVersion
 
 
 
letChannel2HardwareVersion
 
 
 
letChannel2Voltage
 
 
|A collection of line end transponder (LET) objects, available only on devices that support LET connections
 
|A collection of line end transponder (LET) objects, available only on devices that support LET connections
 
|}
 
|}
 +
 
[[Category:Turbine Technical Articles]]
 
[[Category:Turbine Technical Articles]]
 
[[Category:INCA Technical Articles]]
 
[[Category:INCA Technical Articles]]
 
[[Category:Logging]]
 
[[Category:Logging]]
 +
[[Category: IC-EDGE Configuration]]
 +
[[Category: Pulse - Configuration]]
 +
[[Category: SIP intercom - Configuration]]

Latest revision as of 12:41, 12 January 2024

AEIPS.png

Zenitel IP devices run a SNMP service and support SNMP polling and SNMP traps.


Stentofon OID numbers

Zenitel Norway AS has assigned a Private Enterprise Number OID 26122 and the IP-stations use sub OIDs 2,3 and 4.

All Zenitel OIDs definitions can be found in VS-DEVICE-MIB. MIB overview and all OID descriptions are also available at the end of this document.

In addtion to VS-DEVICE-MIB following built in MIBs are also available (not all available for INCA stations): SNMPv2-MIB, IF-MIB, IP-MIB, TCP-MIB, UDP-MIB, HOST-RESOURCES-MIB, NOTIFICATION-LOG-MIB, DISMAN-EVENT-MIB, DISMAN-SCHEDULE-MIB, UCD-SNMP-MIB, UCD-DEMO-MIB, SNMP-TARGET-MIB, NET-SNMP-AGENT-MIB, HOST-RESOURCES-TYPES, NET-SNMP-PASS-MIB, NET-SNMP-EXTEND-MIB, UCD-DLMOD-MIB, SNMP-MPD-MIB, SNMP-USER-BASED-SM-MIB, SNMP-FRAMEWORK-MIB, SNMP-VIEW-BASED-ACM-MIB, SNMP-COMMUNITY-MIB, IP-FORWARD-MIB, SNMP-NOTIFICATION-MIB, SNMPv2-TM, NET-SNMP-VACM-MIB

SNMP Configuration

SNMP is configured from the station web: Advanced Network > SNMP.

SNMP Configuration


SNMP Settings

  • Access: read or none are available, setting none will disable SNMP
  • SNMP v1/v2c: selects SNMP version used, one or both need to be selected for SNMP to work
  • Community string: string used as password for authentication. Use alphanumeric characters. As from firmware 8.1.3.0 also special characters :$#@_?!,-.*' are allowed.
  • Allowed Network: this is used, together with the network mask, to determine the allowed network for reading the MIB on the station. The IP address is entered in regular dot notation, e.g. 10.5.2.100. For example with an allowed network 10.5.2.0 and a network mask of 24, any station with an IP address in the range 10.5.2.0 to 10.5.2.255 can access the MIB. Setting 0.0.0.0/0 will allow all
  • Name: SNMP name string (sent as sysName OID in traps)
  • Location: SNMP Location string
  • Contact: SNMP Contact string

SNMP Trap and Informs Settings

  • Traps/informs receiving server address can be set here
  • If left blank it will disable sending traps/informs

SNMP Custom Configuration File

  • Custom snmpd.conf file can be uploaded and used on the device
  • File is kept during device SW upgrades
  • File syntax and content are not checked and if errors are present in the file it can render SNMP inoperative
  • When custom file is uploaded SNMP Settings are unavailable
  • File can be viewed or downloaded
  • New file can be uploaded at any time
  • When custom file is deleted, the device will revert back to configuration defined in web config

Enable SNMP Traps

  • Available traps (notifications) depend on device type and mode
  • If specific event occurs and corresponding SNMP Trap is enabled, notification (trap) will be generated and sent to trap/inform receiver IP address
  • Traps descriptions

Custom Faults

Custom faults are available only on ENA amplifiers in Edge/SIP/Pulse or Exigo (configurable through EMT) mode. When RCI is triggered, the device will send SNMP Trap with custom fault description and priority.

Configuration for faults is available in web Amplifier Settings -> RCO/RCI Config (or IO Monitoring). For custom faults to be sent traps have to be enabled in config (Advanced Network → SNMP → Enable SNMP Traps → Custom Fault)

Note icon Available only on ENA amplifiers


Custom faults.png

Object Identifier (OID) Numbers

Zenitel Norway AS OID is 26122 (stentofon) → 1.3.6.1.4.1.26122

Overview

Name OID
ipstation 1.3.6.1.4.1.26122.2
     general 1.3.6.1.4.1.26122.2.1
     registration 1.3.6.1.4.1.26122.2.2
     call 1.3.6.1.4.1.26122.2.3
     alarmObjects 1.3.6.1.4.1.26122.2.4
     alarmNotifications 1.3.6.1.4.1.26122.2.5
     faultNotifications 1.3.6.1.4.1.26122.2.8
vsDevice 1.3.6.1.4.1.26122.3
     info 1.3.6.1.4.1.26122.3.1
     temp 1.3.6.1.4.1.26122.3.2
     fan 1.3.6.1.4.1.26122.3.3
     voltage 1.3.6.1.4.1.26122.3.4
     power 1.3.6.1.4.1.26122.3.5
     lineIn 1.3.6.1.4.1.26122.3.6
     ampChannel 1.3.6.1.4.1.26122.3.7
     letStatus 1.3.6.1.4.1.26122.3.8
          letChannel1 1.3.6.1.4.1.26122.3.8.1
          letChannel2 1.3.6.1.4.1.26122.3.8.2
     controlInput 1.3.6.1.4.1.26122.3.9
     controlOutput 1.3.6.1.4.1.26122.3.10
     eth 1.3.6.1.4.1.26122.3.11
     relay 1.3.6.1.4.1.26122.3.12
stentofonMIBConformance 1.3.6.1.4.1.26122.4
     stentofonMIBCompliances 1.3.6.1.4.1.26122.4.1
     stentofonMIBGroups 1.3.6.1.4.1.26122.4.2



ipstation scalar and tabular objects

Name OID Syntax Description
general 1.3.6.1.4.1.26122.2.1
softwareVersion 1.3.6.1.4.1.26122.2.1.1 DisplayString (SIZE (0..255)) The software version
buttonHangingStatus 1.3.6.1.4.1.26122.2.1.2 Integer32 Status of the inputs and DAK buttons, the returned number is bitmap where each bit represents hanging status of one input or DAK button in ascending order
buttonHangingCounter 1.3.6.1.4.1.26122.2.1.3 Counter32 The number of input or buttons hanging since reboot
soundTestLastResult 1.3.6.1.4.1.26122.2.1.4 INTEGER { unused(0), error(1), failed(2), success(3) } Last status of the sound test
soundTestFailedCounter 1.3.6.1.4.1.26122.2.1.5 Counter32 The number of sound tests that failed since reboot
soundTestErrorCounter 1.3.6.1.4.1.26122.2.1.6 Counter32 The number of attempts to automatically set the sound pressure level since reboot
soundTestSuccessCounter 1.3.6.1.4.1.26122.2.1.7 Counter32 The number of sound tests that were successful since reboot
registration 1.3.6.1.4.1.26122.2.2
registrationTable 1.3.6.1.4.1.26122.2.2.1 SEQUENCE OF RegistrationEntry Table of SIP registrations.
registrationEntry 1.3.6.1.4.1.26122.2.2.1.1 RegistrationEntry SIP registration Entry
regIndex 1.3.6.1.4.1.26122.2.2.1.1.1 Unsigned32 The SIP registration table index
serverType 1.3.6.1.4.1.26122.2.2.1.1.2 INTEGER { primary(0), backup(1), backup2(2) } Priority of the SIP server
serverAddress 1.3.6.1.4.1.26122.2.2.1.1.3 DisplayString (SIZE (0..255)) The address of the SIP server
isRegistered 1.3.6.1.4.1.26122.2.2.1.1.4 INTEGER { notregistered(0), registered(1) } SIP registration state of the device towards this SIP server
lastRegistration 1.3.6.1.4.1.26122.2.2.1.1.5 DisplayString (SIZE (0..255)) The time of the last successful registration with this SIP server
call 1.3.6.1.4.1.26122.2.3
callState 1.3.6.1.4.1.26122.2.3.1 INTEGER { idle(0), inprogress(1), incoming(2), outgoing(3), incancel(4) } Call state of the device.
callRemoteId 1.3.6.1.4.1.26122.2.3.2 DisplayString (SIZE (0..255)) The SIP-id of the remote party (empty unless device is in a call)
incomingCallAttempts 1.3.6.1.4.1.26122.2.3.3 Counter32 The number of incoming call attempts since reboot
incomingCallsSuccess 1.3.6.1.4.1.26122.2.3.4 Counter32 The number of successful incoming calls since reboot
incomingCallsFailed 1.3.6.1.4.1.26122.2.3.5 Counter32 The number of incoming calls that has failed since reboot (unanswered calls are not considered failed)
outgoingCallAttempts 1.3.6.1.4.1.26122.2.3.6 Counter32 The number of outgoing call attempts since reboot
outgoingCallsSuccess 1.3.6.1.4.1.26122.2.3.7 Counter32 The number of successful outgoing calls since reboot
outgoingCallsFailed 1.3.6.1.4.1.26122.2.3.8 Counter32 The number of outgoing calls that failed since reboot (unanswered calls are not considered failed)



vsDevice scalar and tabular objects

Name OID Syntax Description
info 1.3.6.1.4.1.26122.3.1
infoPackageVersion 1.3.6.1.4.1.26122.3.1.1 DisplayString(SIZE(128)) The device Package Version
infoModelType 1.3.6.1.4.1.26122.3.1.2 DisplayString(SIZE(128)) The device Model Type.
infoModelNumber 1.3.6.1.4.1.26122.3.1.3 Integer32 (0..9999) The device Model Number.
infoAmplifierType 1.3.6.1.4.1.26122.3.1.4 DisplayString(SIZE(128)) The device Amplifier Type (only for amplifier devices).
infoKernelVersion 1.3.6.1.4.1.26122.3.1.5 DisplayString(SIZE(128)) The device Linux Kernel Version
infoDeviceTreeVersion 1.3.6.1.4.1.26122.3.1.6 DisplayString(SIZE(128)) The device Device Tree Version.
infoDisablement 1.3.6.1.4.1.26122.3.1.7 INTEGER { offline(1), online(2) } The device Disablement status.
temp 1.3.6.1.4.1.26122.3.2
tempTableCount 1.3.6.1.4.1.26122.3.2.1 Integer32 (0..5) Number of Temperature entries in tempTable
tempTable 1.3.6.1.4.1.26122.3.2.2 SEQUENCE OF TempEntry Table of temperature sensors and their values.
tempEntry 1.3.6.1.4.1.26122.3.2.2.1 TempEntry An entry containing a device and its statistics.
tempIndex 1.3.6.1.4.1.26122.3.2.2.1.1 Integer32 (1..5) Reference index for each temperature item
tempSensorName 1.3.6.1.4.1.26122.3.2.2.1.2 DisplayString(SIZE(128)) The name of the temperature sensor we are reading.
tempCurrentString 1.3.6.1.4.1.26122.3.2.2.1.3 DisplayString(SIZE(128)) The current temperature.
tempCurrentValue 1.3.6.1.4.1.26122.3.2.2.1.4 Gauge32 The current temperature of this sensor in the device.
tempPeakString 1.3.6.1.4.1.26122.3.2.2.1.5 DisplayString(SIZE(128)) The peak temperature.
tempPeakValue 1.3.6.1.4.1.26122.3.2.2.1.6 Gauge32 The peak temperature of this sensor in the device.
tempAverageString 1.3.6.1.4.1.26122.3.2.2.1.7 DisplayString(SIZE(128)) The average temperature.
tempAverageValue 1.3.6.1.4.1.26122.3.2.2.1.8 Gauge32 The average temperature of this sensor in the device.
fan 1.3.6.1.4.1.26122.3.3
fanTableCount 1.3.6.1.4.1.26122.3.3.1 Integer32 (0..2) Number of Fan entries in fanTable.
fanTable 1.3.6.1.4.1.26122.3.3.2 SEQUENCE OF FanEntry Table of fans and their RPM status.
fanEntry 1.3.6.1.4.1.26122.3.3.2.1 FanEntry An entry containing a device and its statistics.
fanIndex 1.3.6.1.4.1.26122.3.3.2.1.1 Integer32 (1..2) Reference index for each observed device.
fanString 1.3.6.1.4.1.26122.3.3.2.1.2 DisplayString The name of the fan sensor we are reading.
fanValue 1.3.6.1.4.1.26122.3.3.2.1.3 Gauge32 The rotation speed of the fan in RPM.
voltage 1.3.6.1.4.1.26122.3.4
voltageTableCount 1.3.6.1.4.1.26122.3.4.1 Integer32 (0..20) Number of Voltage entries in voltageTable.
voltageTable 1.3.6.1.4.1.26122.3.4.2 SEQUENCE OF VoltageEntry Table of Voltage sensors and their values.
voltageEntry 1.3.6.1.4.1.26122.3.4.2.1 VoltageEntry An entry containing a device and its Voltage statistics.
voltageIndex 1.3.6.1.4.1.26122.3.4.2.1.1 Integer32 (1..20) Reference index for each observed device.
voltageString 1.3.6.1.4.1.26122.3.4.2.1.2 DisplayString(SIZE(128)) The name of the device we are reading.
voltageValue 1.3.6.1.4.1.26122.3.4.2.1.3 Gauge32 The voltage in mV.
power 1.3.6.1.4.1.26122.3.5
powerTable 1.3.6.1.4.1.26122.3.5.1 SEQUENCE OF PowerEntry Table of Power sources and their status.
powerEntry 1.3.6.1.4.1.26122.3.5.1.1 PowerEntry An entry containing Power source status.
powerIndex 1.3.6.1.4.1.26122.3.5.1.1.1 Integer32 (1..2) Reference index for each observed Power source.
powerType 1.3.6.1.4.1.26122.3.5.1.1.2 INTEGER { unknown(1), acPower(2), dcPower(3), poePower(4) } The type of the Power source we are reading.
powerString 1.3.6.1.4.1.26122.3.5.1.1.3 DisplayString(SIZE(128)) The name of the Power source we are reading.
powerMonitoring 1.3.6.1.4.1.26122.3.5.1.1.4 INTEGER { unknown(1), notMonitored(2), monitored(3) } The Monitoring state of the Power source.
powerStatus 1.3.6.1.4.1.26122.3.5.1.1.5 INTEGER { unknown(1), notConnected(2), connected(3) } The Power source status.
lineIn 1.3.6.1.4.1.26122.3.6
lineInTable 1.3.6.1.4.1.26122.3.6.1 SEQUENCE OF LineInEntry Table of Line In & Microphone and their status.
lineInEntry 1.3.6.1.4.1.26122.3.6.1.1 LineInEntry An entry containing a device and its voltage statistics.
lineInIndex 1.3.6.1.4.1.26122.3.6.1.1.1 Integer32 (1..2) Reference index for each Line In.
lineInMonitoringState 1.3.6.1.4.1.26122.3.6.1.1.2 INTEGER { unknown(1), notMonitored(2), monitored(3) } The monitoring state of the Line In or Microphone.
lineInType 1.3.6.1.4.1.26122.3.6.1.1.3 INTEGER { unknown(1), lineIn1(2), lineIn2(3), microphoneExtern(4), microphoneIntern(5) } The type of the Line In we are reading, either Line In or Microphone.
lineInString 1.3.6.1.4.1.26122.3.6.1.1.4 DisplayString(SIZE(128)) The name of the Line In or Microphone we are reading.
lineInStatus 1.3.6.1.4.1.26122.3.6.1.1.5 INTEGER { unknown(1), lineInOk(2), lineInFail(3), microphoneUnknown(4), microphoneConnected(5), microphoneDisconnected(6), microphoneShorted(7) } The Line In or Microphone status
ampChannel 1.3.6.1.4.1.26122.3.7
ampChannelCount 1.3.6.1.4.1.26122.3.7.1 Integer32 (0..2) The total number of Amplifier channels.
ampType 1.3.6.1.4.1.26122.3.7.2 INTEGER { unknown(1), turbine(2), ena2200(3), ena2400(4), ena2060(5), ena2100(6) } Type of Amplifier.
ampChannelTable 1.3.6.1.4.1.26122.3.7.3 SEQUENCE OF AmpChannelEntry Table of Amplifier channels.
ampChannelEntry 1.3.6.1.4.1.26122.3.7.3.1 AmpChannelEntry An entry containing a Amplifier channel.
ampChannelIndex 1.3.6.1.4.1.26122.3.7.3.1.1 Integer32 (1..2) Index into Amplifier channel table.
ampChannelString 1.3.6.1.4.1.26122.3.7.3.1.2 DisplayString(SIZE(128)) The name of the Amplifier channel.
ampChannelStatus 1.3.6.1.4.1.26122.3.7.3.1.3 INTEGER { unknown(1), notOperative(2), channelOk(3), channelFail(4), channelShutdown(5), channelGracefulDegradation(6) } The Amplifier Channel status.
ampChannelMonitorStatus 1.3.6.1.4.1.26122.3.7.3.1.4 INTEGER { unknown(1), channelOk(2), channelShorted(3), channelOpen(4), channelLoadChange(5), channelGroundFault(6), channelRefreshing(7), channelShutdown(8), channelVoltageLow(9), channelIndecisive(10), channelInterrupted(11), channelTimeoutFail(12), channelMonitoringReceiveError(13), channelMonitoringSuspended(14), channelLineFault(15) } The Amplifier Channel status.
letStatus 1.3.6.1.4.1.26122.3.8
letChannel1 1.3.6.1.4.1.26122.3.8.1
letChannel1Count 1.3.6.1.4.1.26122.3.8.1.1 Integer32 (0..10) The total number of configuration enabled LETs in channel 1.
letChannel1Table 1.3.6.1.4.1.26122.3.8.1.2 SEQUENCE OF LetChannel1Entry Table of LETs and their status.
letChannel1Entry 1.3.6.1.4.1.26122.3.8.1.2.1 LetChannel1Entry An entry containing a LET and status.
letChannel1Index 1.3.6.1.4.1.26122.3.8.1.2.1.1 Integer32 (1..10) The index into this selection of LET data.
letChannel1Description 1.3.6.1.4.1.26122.3.8.1.2.1.2 DisplayString(SIZE(128)) Descriptive text about the LET we are reading.
letChannel1OperativeStatus 1.3.6.1.4.1.26122.3.8.1.2.1.3 INTEGER { unknown(1), notEnabled(2), failed(3), ok(4) } The LET status.
letChannel1SoftwareVersion 1.3.6.1.4.1.26122.3.8.1.2.1.4 DisplayString(SIZE(20)) Software Version of the LET.
letChannel1HardwareVersion 1.3.6.1.4.1.26122.3.8.1.2.1.5 DisplayString(SIZE(20)) Hardware Version of the LET.
letChannel1Voltage 1.3.6.1.4.1.26122.3.8.1.2.1.6 Gauge32 (0..39999) Voltage in mV at LET.
letChannel2 1.3.6.1.4.1.26122.3.8.2
letChannel2Count 1.3.6.1.4.1.26122.3.8.2.1 Integer32 (0..10) The total number of configuration enabled LETs in channel 2
letChannel2Table 1.3.6.1.4.1.26122.3.8.2.2 SEQUENCE OF LetChannel1Entry Table of LETs and their status.
letChannel2Entry 1.3.6.1.4.1.26122.3.8.2.2.1 LetChannel1Entry An entry containing a LET and status.
letChannel2Index 1.3.6.1.4.1.26122.3.8.2.2.1.1 Integer32 (1..10) The index into this selection of LET data.
letChannel2Description 1.3.6.1.4.1.26122.3.8.2.2.1.2 DisplayString(SIZE(128)) Descriptive text about the LET we are reading.
letChannel2OperativeStatus 1.3.6.1.4.1.26122.3.8.2.2.1.3 INTEGER { unknown(1), notEnabled(2), failed(3), ok(4) } The LET status.
letChannel2SoftwareVersion 1.3.6.1.4.1.26122.3.8.2.2.1.4 DisplayString(SIZE(20)) Software Version of the LET.
letChannel2HardwareVersion 1.3.6.1.4.1.26122.3.8.2.2.1.5 DisplayString(SIZE(20)) Hardware Version of the LET.
letChannel2Voltage 1.3.6.1.4.1.26122.3.8.2.2.1.6 Gauge32 (0..39999) Voltage in mV at LET.
controlInput 1.3.6.1.4.1.26122.3.9
controlInputCount 1.3.6.1.4.1.26122.3.9.1 Integer32 (1..6) Number of Control Input entries in controlInputTable.
controlInputTable 1.3.6.1.4.1.26122.3.9.2 SEQUENCE OF ControlInputEntry Table of Control Input sensors and their values.
controlInputEntry 1.3.6.1.4.1.26122.3.9.2.1 ControlInputEntry An entry containing a Control Input and its status.
controlInputIndex 1.3.6.1.4.1.26122.3.9.2.1.1 Integer32 (1..6) Reference index for each Control Input.
controlInputString 1.3.6.1.4.1.26122.3.9.2.1.2 DisplayString(SIZE(128)) The name of the Control Input.
controlInputStatus 1.3.6.1.4.1.26122.3.9.2.1.3 INTEGER { unknown(1), open(2), closed(3), failShorted(4), failOpen(5) } The Control Input status.
controlInputMonitored 1.3.6.1.4.1.26122.3.9.2.1.4 INTEGER { notMonitored(1), monitored(2) } The Control Input Monitored status.
controlOutput 1.3.6.1.4.1.26122.3.10
controlOutputCount 1.3.6.1.4.1.26122.3.10.1 Integer32 (1..6) Number of Control Output entries in controlOutputTable.
controlOutputTable 1.3.6.1.4.1.26122.3.10.2 SEQUENCE OF ControlOutputEntry Table of Control Output sensors and their values.
controlOutputEntry 1.3.6.1.4.1.26122.3.10.2.1 ControlOutputEntry An entry containing a Control Output and its status.
controlOutputIndex 1.3.6.1.4.1.26122.3.10.2.1.1 Integer32 (1..6) Reference index for each Control Output.
controlOutputString 1.3.6.1.4.1.26122.3.10.2.1.2 DisplayString(SIZE(128)) The name of the Control Output.
controlOutputStatus 1.3.6.1.4.1.26122.3.10.2.1.3 INTEGER { unknown(1), notActive(2), active(3), failNotActive(4), failActive(5) } The Control Output status.
eth 1.3.6.1.4.1.26122.3.11
ethMonitoringTable 1.3.6.1.4.1.26122.3.11.1 SEQUENCE OF EthMonitoringEntry Table of Eth Switch Monitoring state.
ethMonitoringEntry 1.3.6.1.4.1.26122.3.11.1.1 EthMonitoringEntry An entry containing an Eth Switch and its Monitoring state.
ethMonitoringIndex 1.3.6.1.4.1.26122.3.11.1.1.1 Integer32 (1..2) Reference index for each Eth Switch Monitored.
ethMonitoringString 1.3.6.1.4.1.26122.3.11.1.1.2 DisplayString(SIZE(128)) The name of the monitored Eth Switch.
ethMonitoringState 1.3.6.1.4.1.26122.3.11.1.1.3 INTEGER { unknown(1), notMonitored(2), monitored(3) } The Eth Switch Monitoring state.
relay 1.3.6.1.4.1.26122.3.12
relayTable 1.3.6.1.4.1.26122.3.12.1 SEQUENCE OF RelayEntry Table of Relay state.
relayEntry 1.3.6.1.4.1.26122.3.12.1.1 RelayEntry An entry containing a Relay and its state.
relayIndex 1.3.6.1.4.1.26122.3.12.1.1.1 Integer32 (1..4) Reference index for each Relay monitored.
relayString 1.3.6.1.4.1.26122.3.12.1.1.2 DisplayString(SIZE(128)) The name of the monitored Relay.
relayIdleMode 1.3.6.1.4.1.26122.3.12.1.1.3 INTEGER { unknown(1), normallyClosed(2), normallyOpen(3) } Relay idle mode state.
relayDelay 1.3.6.1.4.1.26122.3.12.1.1.4 Integer32 (0..30) Delay time (sec) before activation.
relayState 1.3.6.1.4.1.26122.3.12.1.1.5 INTEGER { unknown(1), notActive(2), active(3) } Relay state.



Notifications (traps)

Alarm Objects

Each notification (trap) contains Alarm object with following fields

Name OID Syntax Description
alarmObjects 1.3.6.1.4.1.26122.2.4
managedObjectClass 1.3.6.1.4.1.26122.2.4.1 DisplayString (SIZE (0..255)) This object identifies the class of network to which the subject alarm is related: Stentofon IPStation
managedObjectInstance 1.3.6.1.4.1.26122.2.4.2 DisplayString (SIZE (0..255)) This object identifies the instance (of a class) of network resource to which the subject alarm is related: device hostname
severity 1.3.6.1.4.1.26122.2.4.3 INTEGER { indeterminate(0), critical(1), major(2), minor(3), warning(4), info(5), cleared(6) } The severity of the alarm according to X.733.
time 1.3.6.1.4.1.26122.2.4.4 DisplayString (SIZE(0..255)) The timestamp of the alarm as a string: 'Week day MM DD HH.mm.ss YYYY' eg. Tue Jan 15 19.34.57 2019
description 1.3.6.1.4.1.26122.2.4.5 DisplayString (SIZE(0..255)) Specific problem description.
sysname 1.3.6.1.2.1.1.5 DisplayString (SIZE(0..255)) An administratively-assigned name for this device. NOTE: Not sent when custom snmpd.conf file is used

Alarm/Fault Notifications (Traps)

Availability dependent on device mode (ICX/AlphaCom, Edge, SIP, Pulse...) and device type and model

Name OID Description
alarmNotifications 1.3.6.1.4.1.26122.2.5 NOTE: Available only in Edge/SIP/Pulse mode
ipsStarted 1.3.6.1.4.1.26122.2.5.1 Device has started.
sipRegistered 1.3.6.1.4.1.26122.2.5.3 Device has successfully registered with a SIP server
sipRegisterFailed 1.3.6.1.4.1.26122.2.5.5 Device failed to register with a SIP server
callConnect 1.3.6.1.4.1.26122.2.5.6 Call has connected successfully
callConnectFailed 1.3.6.1.4.1.26122.2.5.7 Call has failed to connect
callDisconnect 1.3.6.1.4.1.26122.2.5.8 Call has disconnected
soundTestSuccess 1.3.6.1.4.1.26122.2.5.10 Sound test was successful
soundTestFailed 1.3.6.1.4.1.26122.2.5.11 Sound test has failed
soundTestError 1.3.6.1.4.1.26122.2.5.12 Automatically setting sound pressure level failed
buttonHanging 1.3.6.1.4.1.26122.2.5.13 Button was pushed for more than 10 seconds without being released
buttonPressed 1.3.6.1.4.1.26122.2.5.14 Input button was pressed. Trap description will provide more info about input number
buttonReleased 1.3.6.1.4.1.26122.2.5.15 Input button was released. Trap description will provide more info about input number
relayActivated 1.3.6.1.4.1.26122.2.5.16 Relay was activated. Trap description will provide more info about relay number
relayDeactivated 1.3.6.1.4.1.26122.2.5.17 Relay was deactivated. Trap description will provide more info about relay number
dakPressed 1.3.6.1.4.1.26122.2.5.18 DAK was pressed. Trap description will provide more info about DAK number
dakReleased 1.3.6.1.4.1.26122.2.5.19 DAK was released. Trap description will provide more info about DAK number
faultNotifications 1.3.6.1.4.1.26122.2.8 NOTE: Available depending on device type and model, eg. amplifier, kit, device has ETH switch...
coolingFanFault 1.3.6.1.4.1.26122.2.8.1 There is a cooling fan fault eg. low speed, not running. Trap description will provide RPM and fan details
missingAmpModule 1.3.6.1.4.1.26122.2.8.2 Amplifier module is missing
psuVoltageFault 1.3.6.1.4.1.26122.2.8.3 Power supply voltage is not within operational range. Trap description will provide more information about voltage values
lineVoltageFault 1.3.6.1.4.1.26122.2.8.4 Selected speaker line voltage is not applied.
letFault 1.3.6.1.4.1.26122.2.8.5 Reported only if Line End Transponder (LET) monitoring enabled and configured. LET has failed. Trap description will provide let channel and number
ampShutdown 1.3.6.1.4.1.26122.2.8.6 Amplifier audio channel is shut down. Trap description will provide details about affected channel
slmFault 1.3.6.1.4.1.26122.2.8.7 Speaker Line Monitoring (SLM) related fault has occurred. Trap description will provide fault details and affected channel
fuseBroken 1.3.6.1.4.1.26122.2.8.8 Fuse is broken. Trap description will provide information about affected fuse
ampDisabled 1.3.6.1.4.1.26122.2.8.9 Amplifier audio channel is disabled. Trap description will provide details about affected channel
lineInFault 1.3.6.1.4.1.26122.2.8.10 Reported only if Line In monitoring enabled. Line in is disconnected
rcoFault 1.3.6.1.4.1.26122.2.8.11 Reported only if RCO monitoring enabled. Control output is not set or cleared. Trap description will provide more info about affected output and fault details
rciFault 1.3.6.1.4.1.26122.2.8.12 Reported only if RCI monitoring enabled. Control input shorted or not connected. Trap description will provide more info about affected input and fault details
dcPowerFault 1.3.6.1.4.1.26122.2.8.13 Reported only if DC Power monitoring enabled. DC power disconnected
acPowerFault 1.3.6.1.4.1.26122.2.8.14 Reported only if AC Power monitoring enabled. AC power disconnected
ethPortDisconnected 1.3.6.1.4.1.26122.2.8.15 Reported only if ETH port monitoring enabled. Ethernet port is disconnected. Trap description will provide more info about affected port number
micFault 1.3.6.1.4.1.26122.2.8.16 Reported only if mic monitoring is enabled. Microphone is not connected or shorted. Trap description will provide fault details
missingEmbdr 1.3.6.1.4.1.26122.2.8.17 Panel device is missing EMBDR expansion modules
swFault 1.3.6.1.4.1.26122.2.8.18 Software daemon has stopped working. Trap description will provide more info about affected daemon
tempFault 1.3.6.1.4.1.26122.2.8.19 High temperature is detected. Trap description will provide more info about value and affected sensor.
customFault 1.3.6.1.4.1.26122.2.8.20 Report External Custom Faults. Trap description will provide more info about fault

Some example trap descriptions

Name Trap description
ethPortDisconnected community=public, enterprise=1.3.6.1.4.1.26122.2.8.15, uptime=7770, agent_ip=10.9.6.223, version=Ver2, 1.3.6.1.4.1.26122.2.4.1.0="Stentofon IPStation", 1.3.6.1.4.1.26122.2.4.2.0=zenitel0c0c2a, sysName=Amplifier, 1.3.6.1.4.1.26122.2.4.3.0=1, 1.3.6.1.4.1.26122.2.4.4.0="Mon Oct 11 12.22.22 2021

", 1.3.6.1.4.1.26122.2.4.5.0="Ethernet Port 2 disconnected"

tempFault community=public, enterprise=1.3.6.1.4.1.26122.2.8.19, uptime=122149, agent_ip=10.9.6.120, version=Ver2, 1.3.6.1.4.1.26122.2.4.1.0="Stentofon IPStation", 1.3.6.1.4.1.26122.2.4.2.0=zenitel0c0c2b, sysName=Amplifier, 1.3.6.1.4.1.26122.2.4.3.0=4, 1.3.6.1.4.1.26122.2.4.4.0="Thu Sep  9 07.38.24 2021

", 1.3.6.1.4.1.26122.2.4.5.0="Temp Sensor Main board, Warning High, measured 65.5C, limit 65.0C"

psuVoltageFault community=public, enterprise=1.3.6.1.4.1.26122.2.8.3, uptime=2199, agent_ip=10.9.6.223, version=Ver2, 1.3.6.1.4.1.26122.2.4.1.0="Stentofon IPStation", 1.3.6.1.4.1.26122.2.4.2.0=zenitel0c0c2a, sysName=Amplifier, 1.3.6.1.4.1.26122.2.4.3.0=2, 1.3.6.1.4.1.26122.2.4.4.0="Tue Oct 12 06.59.52 2021

", 1.3.6.1.4.1.26122.2.4.5.0="Internal Power 50.00  too low_alert, measured 39.80V, limit 45.00V"

Compliance and groups

Compliance

Name OID Content
stentofonMIBCompliances 1.3.6.1.4.1.26122.4.1
Mandatory Groups alarmObjectsGroup, sipNotificationsGroup, faultNotificationsGroup, deviceInfoGroup, sipGeneralGroup
Optional Groups sipRegistrationGroup, sipCallGroup, deviceStatusGroup, audioInputsGroup, controlIOGroup, ethernetGroup, amplifierGroup, letsGroup

Groups

Name OID Content Description
stentofonMIBGroups 1.3.6.1.4.1.26122.4.2
sipRegistrationGroup 1.3.6.1.4.1.26122.4.2.1 serverType, serverAddress, isRegistered, lastRegistration A collection of registration related objects, available only when device is in Edge/SIP/Pulse mode"
sipCallGroup 1.3.6.1.4.1.26122.4.2.2 callState, callRemoteId, incomingCallAttempts, incomingCallsSuccess, incomingCallsFailed, outgoingCallAttempts, outgoingCallsSuccess, outgoingCallsFailed A collection of call state related objects, available only when device is in Edge/SIP/Pulse mode
sipGeneralGroup 1.3.6.1.4.1.26122.4.2.3 softwareVersion, buttonHangingStatus, buttonHangingCounter, soundTestLastResult, soundTestFailedCounter, soundTestErrorCounter, soundTestSuccessCounter A collection of general device info objects available only when device is in Edge/SIP/Pulse mode
alarmObjectsGroup 1.3.6.1.4.1.26122.4.2.4 managedObjectClass, managedObjectInstance, severity, time, description A collection of objects included in all notifications
sipNotificationsGroup 1.3.6.1.4.1.26122.4.2.5 ipsStarted, ipsShutdown, sipRegistered, sipUnregistered, sipRegisterFailed, callConnect, callConnectFailed, callDisconnect, callAbnormalDisconnect, soundTestSuccess, soundTestFailed, soundTestError, buttonHanging, buttonPressed, buttonReleased, relayActivated, relayDeactivated, dakPressed, dakReleased A collection of notifications available only when device is in Edge/SIP/Pulse mode and dependent on device type and model
faultNotificationsGroup 1.3.6.1.4.1.26122.4.2.6 coolingFanFault, missingAmpModule, psuVoltageFault, lineVoltageFault, letFault, ampShutdown, slmFault, fuseBroken, ampDisabled, lineInFault, rcoFault, rciFault, dcPowerFault, acPowerFault, ethPortDisconnected, micFault, missingEmbdr, swFault, tempFault, customFault A collection of fault monitoring related notifications, availability based on device type and model
deviceInfoGroup 1.3.6.1.4.1.26122.4.2.7 infoPackageVersion, infoModelType, infoModelNumber, infoAmplifierType, infoKernelVersion, infoDeviceTreeVersion, infoDisablement A collection of device info objects, some fields not available on all device types
deviceStatusGroup 1.3.6.1.4.1.26122.4.2.8 tempTableCount, tempSensorName, tempCurrentString, tempCurrentValue, tempPeakString, tempPeakValue, tempAverageString, tempAverageValue, fanTableCount, fanString, fanValue, voltageTableCount, voltageString, voltageValue, powerType, powerString, powerMonitoring, powerStatus A collection of device temperature, fan speed, internal voltages and power status objects, available on amplifier devices
audioInputsGroup 1.3.6.1.4.1.26122.4.2.9 lineInMonitoringState, lineInType, lineInString, lineInStatus A collection of audio inputs device objects, available only on devices with microphone or line in monitoring
controlIOGroup 1.3.6.1.4.1.26122.4.2.10 controlInputCount, controlInputString, controlInputStatus, controlInputMonitored, controlOutputCount, controlOutputString, controlOutputStatus, relayString, relayIdleMode, relayDelay, relayState A collection of control input and control output (CIO) device objects, available only on devices with CIO monitoring
ethernetGroup 1.3.6.1.4.1.26122.4.2.11 ethMonitoringString, ethMonitoringState A collection of Ethernet switch monitoring objects, available on devices with Ethernet switch
amplifierGroup 1.3.6.1.4.1.26122.4.2.12 ampChannelCount, ampType, ampChannelString, ampChannelStatus, ampChannelMonitorStatus A collection of amplifier info objects
letsGroup 1.3.6.1.4.1.26122.4.2.13 letChannel1Count, letChannel1Description, letChannel1OperativeStatus, letChannel1SoftwareVersion, letChannel1HardwareVersion, letChannel1Voltage, letChannel2Count, letChannel2Description, letChannel2OperativeStatus, letChannel2SoftwareVersion, letChannel2HardwareVersion, letChannel2Voltage A collection of line end transponder (LET) objects, available only on devices that support LET connections