Actions

Difference between revisions of "Tamper and Vandal Proof Station - 1007063000"

From Zenitel Wiki
Line 1: Line 1:
 
[[Image:Tamper and Vandal Proof Station 100 7063 000.jpg|thumb|150px|100 7063 000 station]]
 
[[Image:Tamper and Vandal Proof Station 100 7063 000.jpg|thumb|150px|100 7063 000 station]]
  
−
== Features ==
+
== Highlights ==
 
* Analogue intercom station specially designed for prison and correctional facilities
 
* Analogue intercom station specially designed for prison and correctional facilities
 
* Advanced safety solution including scream, assault and tamper alarms
 
* Advanced safety solution including scream, assault and tamper alarms
Line 11: Line 11:
 
* Redundant backup for power and signaling
 
* Redundant backup for power and signaling
  
−
== Description ==
+
==Additional Documentation==
−
The Tamper and Vandal Proof station type 1007063000 is
+
For more documentation please see http://www.zenitel.com/product/product/tamper-and-vandal-proof-station
−
designed specially for prisons and correctional facilities with
 
−
safety and security for both guards and prisoners in mind.
 
−
 
 
−
The station is much more than a traditional intercom for prison
 
−
cells. The station comes with inbuilt scream alarm, assault
 
−
alarm, light signaling, external controls, entertainment functions
 
−
and cell light switch.
 
−
 
 
−
The front plate is in 2,5 mm stainless steel and equipped with 5
 
−
vandal proof sensor buttons. If the prisoner in some way should
 
−
manage to open the station, a tamper alarm will be triggered.
 
−
If the station is disconnected, or the wires to the station are
 
−
shorted, a request for action will be generated.
 
−
 
 
−
Call request form the cell, guard presence and alarm calls are
 
−
indicated on the guard’s intercom station as well as by signal
 
−
lamps outside the cell and in the guard room.
 
−
 
 
−
The station works in a dual redundant mode. If the link to the
 
−
intercom exchange fails, the lamp signaling will still work. If the
 
−
lamp signaling fails, all intercom signaling will remain intact.
 
−
 
 
−
The sensitivity of the vandal proof sensor buttons can be set to
 
−
‘normal’ or ‘high’, where the latter is intended for use by guards
 
−
wearing rubber gloves. In order to keep the sensitivity at the
 
−
correct level, the stations must be installed in a dry, indoor
 
−
location.
 
−
 
 
−
For cleaning purposes, the station is protected to IP65; fluid
 
−
will not harm the station, but operation is only optimal when the
 
−
surface is dry again.
 
−
 
 
−
== Specifications ==
 
−
{|
 
−
|width="150px"|Dimensions: (WxHxD)
 
−
|128 x 264 x 51 mm, 5.0 x 10.4 x 2.4 in
 
−
|-
 
−
|Weight || 950 g, 2.1 lb
 
−
|-
 
−
|Finish || 2.5 mm brushed stainless steel
 
−
|-
 
−
|Mounting || Flush in back box, 6 tamper proof screws
 
−
|-
 
−
|Button || Vandal proof sensor type
 
−
|-
 
−
|Gen. purp. I/O ports || 3 x input - contact closure, 2 x output - 24VDC/1A
 
−
|-
 
−
|Lamp outputs || Call - present - tamper - group
 
−
|-
 
−
|Lamp drivers || 24VDC/1A overload protected
 
−
|-
 
−
|Operating Voltage || 24 (11-27) VDC
 
−
|-
 
−
|Cable Requirements || 2 pair twisted cable, 0.5-0.6 mm / 24 AWG
 
−
|-
 
−
|Temperature || -40 C to +55 C
 
−
|-
 
−
|Relative humidity || 0% - 95%
 
−
|-
 
−
|Loudspeaker Output || 1 W RMS
 
−
|-
 
−
|Frequency Range || 200 - 10000 Hz
 
−
|-
 
−
|Back-box type || LBB 7076/76
 
−
|-
 
−
|}
 
  
 
== Installation ==
 
== Installation ==
−
[[image:Tamper and Vandal Proof Station 100 7063 000 Installation.jpg|thumb|left|250px|]]<br>
+
[[image:Tamper and Vandal Proof Station 100 7063 000 Installation.jpg|thumb|left|500px|]]
−
<br>
+
<br style="clear:both;" />
−
<br>
 
−
<br>
 
−
<br>
 
−
<br>
 
−
<br>
 
−
<br>
 
  
 
== Flush Mount Back Box With Anchors ==
 
== Flush Mount Back Box With Anchors ==
 
[[image:Tamper and Vandal Proof Station 100 7063 000 Flush mount back box.jpg|thumb|left|250px]]
 
[[image:Tamper and Vandal Proof Station 100 7063 000 Flush mount back box.jpg|thumb|left|250px]]
 
[[Image:890070737601.PNG|thumb|right|250px]]
 
[[Image:890070737601.PNG|thumb|right|250px]]
−
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  

Revision as of 12:06, 7 August 2015

100 7063 000 station

Highlights

  • Analogue intercom station specially designed for prison and correctional facilities
  • Advanced safety solution including scream, assault and tamper alarms
  • Vandal proof design with 2.5 mm steel front, sensor buttons, microphone/speaker protection and water resistant
  • Music distribution with volume control
  • Integrated light signaling system
  • Integrated cell light button and switch
  • Programmable I/O ports for controlling door status, lamps, TV sets, sensors and more
  • Redundant backup for power and signaling

Additional Documentation

For more documentation please see http://www.zenitel.com/product/product/tamper-and-vandal-proof-station

Installation

Tamper and Vandal Proof Station 100 7063 000 Installation.jpg


Flush Mount Back Box With Anchors

Tamper and Vandal Proof Station 100 7063 000 Flush mount back box.jpg
890070737601.PNG


Related Articles

Retrieved from "https://wiki.zenitel.com/w/index.php?title=Tamper_and_Vandal_Proof_Station_-_1007063000&oldid=36348"