Actions

Difference between revisions of "Turbine 4.11 - Release notes"

From Zenitel Wiki

(Known Issues)
(MTN-1073 Group call fails if system previously configured with ZAP)
Line 70: Line 70:
 
If system was configured with ZAP (VS-IMT Pulse SDK project) and then switched to XML configuration by deleting data.lua file, it is possible that Group Calls shall not work. A workaround is that (1) data.lua file is deleted from all stations including Pulse server - this will reboot stations, and (2) after reboot go to Server configuration -> Save + Apply - this will again reboot all stations
 
If system was configured with ZAP (VS-IMT Pulse SDK project) and then switched to XML configuration by deleting data.lua file, it is possible that Group Calls shall not work. A workaround is that (1) data.lua file is deleted from all stations including Pulse server - this will reboot stations, and (2) after reboot go to Server configuration -> Save + Apply - this will again reboot all stations
  
 
+
===MTN-598 IP station fails to register if Hebrew name is too long===
 +
More than 12 characters entered causes registration problems
  
  
 
[[Category: Release notes]]
 
[[Category: Release notes]]

Revision as of 15:24, 9 January 2019

Release info

Name: VSF-Turbine
Description: VSF-Turbine is a firmware archive for all Turbine Family Intercom stations including devices: TCIS-x, TKIS-2, TCIV-x, TMIS-x, TFIE-x, TKIE-x, TFIX-x, ECPIR-3P, ENA-2060AC (only in SIP mode), Exigo IP speakers and Exigo Network Amplifiers (AlphaCom mode only).
Version: The firmware is delivered in two different ZIP archives:

  • vsft-4.11.2.x - Used for standard in-field upgrades
  • vsft-prod-4.11.2.x - Used in production- and recovery upgrades.

Version: 4.11.2.5
Date: 15.01.2019
Status: Limited Availability

VSF-TURBINE 4.11.2.5

New Features - Turbine Intercom

SNOW-496 IP Station support for RFC3891 SIP "Replaces" Header

The IP Station (Turbine and INCA) now support Reinvite / INVITE with replaces, which is quite common function used in SIP environments. The needed function is described in RFC3891.

SNOW-818 Keep-alive for improved VoIP NAT traversal

NAT keep-alive is a feature that sends very tiny UDP data packets from a VoIP client to the router to show that the port is still in use. Turbine and INCA are now sending keep-alives every 25 seconds if have enabled "NAT Keep Alive" under Call Settings.

SNOW-330 IP Multicast audio support for Pulse Intercom

Turbine and INCA IP intercom stations now support IP multicast audio when configured in Pulse mode. Previously, only SIP mode was supported. Up to 10 multicast IP addresses can be configured.

SNOW-192 Chinese font on Turbine OLED display

Turbine now supports Chinese language characters with new font package. New vsf-chinese-font_x.x.x.x_armel.ipk package is made, which can be installed on the turbine (download can be found on our Wiki)

SNOW-871 TCIV-5 firmware support

Turbine firmware now supports a new TCIV-5 Turbine IP station model.

SNOW-1165 Image quality improvements for TCIV

Low-level optimizations were made for AEWB engine (Automatic Exposure and White Balancing) resulting in following image quality improvements: Better low-light performance, Better overall color accuracy and contrast, Smoother dynamic dark-light transitions.

SNOW-83 ONVIF Profile-S support on TCIV

TCIV now fully supports and is compliant with ONVIF Profile-S specification. As a standard in the industry, Profile-S can be used to integrate with a variety of VMS and NVR products.

SNOW-1166 RTSP support for TCIV video stream

RTSP is an industry standard network control protocol for establishing and controlling media streams. TCIV now comes with a full support for RTSP video streams.

SNOW-1169 Dual stream functionality on TCIV

TCIV now supports dual-streaming functionality where two independent video streams can be separately initiated and controlled. Streams can be configured with different protocols (SIP, RTSP, ONVIF, HTTP), different codec and resolution, and are both lip-synced if audio and video is being used - using the industry standard RTCP protocol.

SNOW-1167 RTSP audio stream support for all Turbine devices

RTSP is an industry standard network control protocol for establishing and controlling media streams. All Turbine intercom devices and kits now fully support RTSP for outgoing audio streams.

SNOW-1168 Lip-sync of Audio and Video on TCIV

Audio and Video streams initiated using ONVIF or RTSP protocols are lip-synced for both streaming and recording, implemented using the industry standard RTP Control Protocol (RTCP).

New Features - Technical Preview

SNOW-330 IP Multicast audio support for Pulse Intercom

Turbine and INCA IP intercom stations now support IP multicast audio when configured in Pulse mode. Previously, only SIP mode was supported. Up to 10 multicast IP addresses can be configured.

Bugfixes and Improvements

Known Issues

VSIS-878 Factory reset does not delete uploaded Script

All uploaded scripts should also be removed on Factory reset

SNOW-1124 TCIV H264 stream does not work in Honeywell Maxpro NVR

Managed to get MJPEG stream in Honeywell, H264 does not work for some reason

SNOW-1093 Hikvision CE-NVR issues with TCIV H264 stream

Video streaming on CE-NVR-16/32 showed image artifacts

SNOW-760 TCIV H264 stream does not work in Xtrails/Honeywell ADPRO iFT Series NVR

TCIV sends it’s H.264 I-Frames (IDR_SLICE) in multiple NAL units which causes incompatibitliy issues with Xtrails/Honeywell ADPRO iFT Series NVR

MTN-2220 Default SNMP settings issue with firmware downgrade to 4.9

When downgrading from VSFT 4.10+ to 4.9 a factory reset is necessary if user wants to use default SNMP configuration. For custom snmp.conf file, re-upload with a custom snmp.conf file will fix the problem.

MTN-1073 Group call fails if system previously configured with ZAP

If system was configured with ZAP (VS-IMT Pulse SDK project) and then switched to XML configuration by deleting data.lua file, it is possible that Group Calls shall not work. A workaround is that (1) data.lua file is deleted from all stations including Pulse server - this will reboot stations, and (2) after reboot go to Server configuration -> Save + Apply - this will again reboot all stations

MTN-598 IP station fails to register if Hebrew name is too long

More than 12 characters entered causes registration problems