Difference between revisions of "Turbine 4.11 - Release notes"
From Zenitel Wiki
(→New Features - Turbine Intercom) |
(→Bugfixes and Improvements - Turbine Intercom) |
||
Line 136: | Line 136: | ||
== Bugfixes and Improvements - Turbine Intercom == | == Bugfixes and Improvements - Turbine Intercom == | ||
+ | === MTN-1709 Fault led on all Turbine industrial stations, Turbine EX stations and Exigo Access panels can now be configured with custom behavior in Alphacom=== | ||
+ | |||
+ | === SNOW-319 TKIE-3 support in Turbine firmware=== | ||
+ | TKIE-3 is now supported in Turbine firmware | ||
+ | |||
+ | === SNOW-321 Implement Distributed AVC in SIP Mode=== | ||
+ | All "Turbine Devices" can be AVC Source (Ambient audio listener) or AVC destination. | ||
+ | |||
+ | === SNOW-328 Adjust volume using SIP OPTIONS with X-Header=== | ||
+ | It is now possible to adjust volume using SIP OPTIONS with x-header by adding x-volume-level-override. The function will override the configured station volume | ||
+ | |||
+ | === SNOW-552 Syslog support === | ||
+ | Turbine now supports logging to the syslog server. Up to 3 syslog server destinations are supported | ||
+ | |||
+ | === SNOW-592 AGC for line/mic in=== | ||
+ | Automatic Gain Control now works for Line/Mic in depending on configured input selection | ||
+ | |||
+ | === SNOW-1173 New call functions in SIP=== | ||
+ | It is now possible to put call on hold or defer a call using DAK configuration | ||
== Security fixes and improvements == | == Security fixes and improvements == |
Revision as of 09:52, 1 April 2019
Contents
- 1 Release info
- 2 VSF-TURBINE 4.11.2.5
- 2.1 New Features - Turbine Intercom
- 2.1.1 SNOW-496 IP Station support for RFC3891 SIP "Replaces" Header
- 2.1.2 SNOW-818 Keep-alive for improved VoIP NAT traversal
- 2.1.3 SNOW-330 IP Multicast audio support for Pulse Intercom
- 2.1.4 SNOW-192 Chinese font on Turbine OLED display
- 2.1.5 SNOW-871 TCIV-5 firmware support
- 2.1.6 SNOW-1165 Image quality improvements for TCIV
- 2.1.7 SNOW-83 ONVIF Profile-S support on TCIV
- 2.1.8 SNOW-1166 RTSP support for TCIV video stream
- 2.1.9 SNOW-1169 Dual stream functionality on TCIV
- 2.1.10 SNOW-1167 RTSP audio stream support for all Turbine devices
- 2.1.11 SNOW-1168 Lip-sync of Audio and Video on TCIV
- 2.2 New Features - Technical Preview
- 2.3 Bugfixes and Improvements - Turbine Intercom
- 2.3.1 MTN-1527 IP Multicast Audio audible interruptions
- 2.3.2 MTN-1930 TFIE-6 does not display AlphaCom status-messages in Idle
- 2.3.3 MTN-1498 Group call fails after Pulse Server reboots and takes ~ 5 min to work again
- 2.3.4 MTN-1974 Sound detection on Turbine is not triggered properly
- 2.3.5 MTN-2122 In HD Audio mode the station would report missing RTP
- 2.3.6 MTN-2086 AEC Performance Improvements - Reduced Echo Artifacts
- 2.3.7 MTN-2246 Need review h4. Suspend monitoring not always working for ENA in AlphaCom
- 2.3.8 MTN-2085 Far-End signal limiter on Turbine
- 2.3.9 MTN-2019 TCIV displays incorrect default image resolution for MJPEG HTTP
- 2.3.10 SNOW-313 RTSP support for TCIV H.264 stream (AlphaCom)
- 2.3.11 SNOW-1163 IP-LCM IO does not work properly in Pulse/SIP mode
- 2.3.12 SNOW-1170 TCIV limitations for image resolution
- 2.3.13 SNOW-887 Video setup mode "Cisco" removed
- 2.3.14 SNOW-1030 Video preview interrupted after answering the call
- 2.4 Security fixes and improvements
- 2.5 Known Issues
- 2.5.1 VSIS-878 Factory reset does not delete uploaded Script
- 2.5.2 SNOW-1124 TCIV H264 stream does not work in Honeywell Maxpro NVR
- 2.5.3 SNOW-1093 Hikvision CE-NVR issues with TCIV H264 stream
- 2.5.4 SNOW-760 TCIV H264 stream does not work in Xtrails/Honeywell ADPRO iFT Series NVR
- 2.5.5 MTN-2220 Default SNMP settings issue with firmware downgrade to 4.9
- 2.5.6 MTN-1073 Group call fails if system previously configured with ZAP
- 2.5.7 MTN-598 IP station fails to register if Hebrew name is too long
- 2.1 New Features - Turbine Intercom
- 3 VSF-TURBINE 4.10.3.0
- 3.1 New Features - Turbine Intercom
- 3.2 New Features - Exigo Amplifiers
- 3.3 Bugfixes and Improvements - Turbine Intercom
- 3.3.1 MTN-1709 Fault led on all Turbine industrial stations, Turbine EX stations and Exigo Access panels can now be configured with custom behavior in Alphacom
- 3.3.2 SNOW-319 TKIE-3 support in Turbine firmware
- 3.3.3 SNOW-321 Implement Distributed AVC in SIP Mode
- 3.3.4 SNOW-328 Adjust volume using SIP OPTIONS with X-Header
- 3.3.5 SNOW-552 Syslog support
- 3.3.6 SNOW-592 AGC for line/mic in
- 3.3.7 SNOW-1173 New call functions in SIP
- 3.4 Security fixes and improvements
- 3.5 Known Issues
Release info
Name: VSF-Turbine
Description: VSF-Turbine is a firmware archive for all Turbine Family Intercom stations including devices:
TCIS-x, TKIS-2, TCIV-x, TMIS-x, TFIE-x, TKIE-x, TFIX-x, ECPIR-3P, ENA-2060AC (only in SIP mode), Exigo IP speakers and Exigo Network Amplifiers (AlphaCom mode only).
Version: The firmware is delivered in two different ZIP archives:
- vsft-4.11.2.x - Used for standard in-field upgrades
- vsft-prod-4.11.2.x - Used in production- and recovery upgrades.
Version: 4.11.2.5
Date: 15.01.2019
Status: Limited Availability
VSF-TURBINE 4.11.2.5
New Features - Turbine Intercom
SNOW-496 IP Station support for RFC3891 SIP "Replaces" Header
The IP Station (Turbine and INCA) now support Reinvite / INVITE with replaces, which is quite common function used in SIP environments. The needed function is described in RFC3891.
SNOW-818 Keep-alive for improved VoIP NAT traversal
NAT keep-alive is a feature that sends very tiny UDP data packets from a VoIP client to the router to show that the port is still in use. Turbine and INCA are now sending keep-alives every 25 seconds if have enabled "NAT Keep Alive" under Call Settings.
SNOW-330 IP Multicast audio support for Pulse Intercom
Turbine and INCA IP intercom stations now support IP multicast audio when configured in Pulse mode. Previously, only SIP mode was supported. Up to 10 multicast IP addresses can be configured.
SNOW-192 Chinese font on Turbine OLED display
Turbine now supports Chinese language characters with new font package. New vsf-chinese-font_x.x.x.x_armel.ipk package is made, which can be installed on the turbine (download can be found on our Wiki)
SNOW-871 TCIV-5 firmware support
Turbine firmware now supports a new TCIV-5 Turbine IP station model.
SNOW-1165 Image quality improvements for TCIV
Low-level optimizations were made for AEWB engine (Automatic Exposure and White Balancing) resulting in following image quality improvements: Better low-light performance, Better overall color accuracy and contrast, Smoother dynamic dark-light transitions.
SNOW-83 ONVIF Profile-S support on TCIV
TCIV now fully supports and is compliant with ONVIF Profile-S specification. As a standard in the industry, Profile-S can be used to integrate with a variety of VMS and NVR products.
SNOW-1166 RTSP support for TCIV video stream
RTSP is an industry standard network control protocol for establishing and controlling media streams. TCIV now comes with a full support for RTSP video streams.
SNOW-1169 Dual stream functionality on TCIV
TCIV now supports dual-streaming functionality where two independent video streams can be separately initiated and controlled. Streams can be configured with different protocols (SIP, RTSP, ONVIF, HTTP), different codec and resolution, and are both lip-synced if audio and video is being used - using the industry standard RTCP protocol.
SNOW-1167 RTSP audio stream support for all Turbine devices
RTSP is an industry standard network control protocol for establishing and controlling media streams. All Turbine intercom devices and kits now fully support RTSP for outgoing audio streams.
SNOW-1168 Lip-sync of Audio and Video on TCIV
Audio and Video streams initiated using ONVIF or RTSP protocols are lip-synced for both streaming and recording, implemented using the industry standard RTP Control Protocol (RTCP).
New Features - Technical Preview
SNOW-330 IP Multicast audio support for Pulse Intercom
Turbine and INCA IP intercom stations now support IP multicast audio when configured in Pulse mode. Previously, only SIP mode was supported. Up to 10 multicast IP addresses can be configured.
Bugfixes and Improvements - Turbine Intercom
MTN-1527 IP Multicast Audio audible interruptions
It is possible to hear audible effects during IP Multicast audio playback, and with a relatively high interval rate.
MTN-1930 TFIE-6 does not display AlphaCom status-messages in Idle
AlphaCom status messages did not work correctly on TFIE-6. For example, it was not possible to see if a TFIE-6 is forwarded(71,72) or marked absent(77x).
MTN-1498 Group call fails after Pulse Server reboots and takes ~ 5 min to work again
The registration information is now properly stored in the Pulse server and Group call shall work immediately after server restart.
MTN-1974 Sound detection on Turbine is not triggered properly
Sound Detection is never triggered on, but "DAK off" is reported. Fixed
MTN-2122 In HD Audio mode the station would report missing RTP
In HD Audio mode the station would incorrectly report missing RTP when it is meant to only send audio. This has been fixed.
MTN-2086 AEC Performance Improvements - Reduced Echo Artifacts
By tuning the Acoustic Echo Cancellation algorithm options we have reduced the level of produced Echo artifacts on Turbine stations at high-level speaker outputs.
MTN-2246 Need review h4. Suspend monitoring not always working for ENA in AlphaCom
Certain directory number configurations could previously stop suspend monitoring from working when using Exigo network amplifiers (ENA) in AlphaCom mode. This has been fixed.
MTN-2085 Far-End signal limiter on Turbine
Far-End signal Limiter filter is designed to avoid powerful Far-End signal bringing the station to PoE shutdown as well as try to avoid Far-End Signal clipping and distortions.
MTN-2019 TCIV displays incorrect default image resolution for MJPEG HTTP
When opening HTTP MJPEG video stream in a web browser (http://IP-Address:8090) the video is displayed in smaller resolution then a defined default of 480p.
SNOW-313 RTSP support for TCIV H.264 stream (AlphaCom)
Added RTSP H.264 support on ITSV-1 to initiate video stream from TCIV in AlphaCom mode
SNOW-1163 IP-LCM IO does not work properly in Pulse/SIP mode
Some outputs/inputs on the IP-LCM are mapped wrongly in Pulse/SIP mode and does not work as expected when configured in the web.
SNOW-1170 TCIV limitations for image resolution
Image resolution for both H264 and MJPEG is now limited to max 480p which increased product stability and overall robustness. Many low-level optimizations were made for AEWB engine (Automatic Exposure and White Balancing) resulting in much better color accuracy, low-light performance and contrast
SNOW-887 Video setup mode "Cisco" removed
Due to the fixes in video stream FPS stability the "Cisco" video setup mode was made obsolete and therefore removed from StationWeb options
SNOW-1030 Video preview interrupted after answering the call
A video preview stream is initially started when ITSV-1 is ringing, but once the call is answered stream will be stopped and new one will be started, and in this case video is lost for 4-5 seconds. This is now fixed
Security fixes and improvements
VSIS-1272 Basic MJPEG HTTP authentication should be enabled by default
Now the option to Enable basic HTTP authentication for HTTP MJPEG is enabled by default
Known Issues
VSIS-878 Factory reset does not delete uploaded Script
All uploaded scripts should also be removed on Factory reset
SNOW-1124 TCIV H264 stream does not work in Honeywell Maxpro NVR
Managed to get MJPEG stream in Honeywell, H264 does not work for some reason
SNOW-1093 Hikvision CE-NVR issues with TCIV H264 stream
Video streaming on CE-NVR-16/32 showed image artifacts
SNOW-760 TCIV H264 stream does not work in Xtrails/Honeywell ADPRO iFT Series NVR
TCIV sends it’s H.264 I-Frames (IDR_SLICE) in multiple NAL units which causes incompatibitliy issues with Xtrails/Honeywell ADPRO iFT Series NVR
MTN-2220 Default SNMP settings issue with firmware downgrade to 4.9
When downgrading from VSFT 4.10+ to 4.9 a factory reset is necessary if user wants to use default SNMP configuration. For custom snmp.conf file, re-upload with a custom snmp.conf file will fix the problem.
MTN-1073 Group call fails if system previously configured with ZAP
If system was configured with ZAP (VS-IMT Pulse SDK project) and then switched to XML configuration by deleting data.lua file, it is possible that Group Calls shall not work. A workaround is that (1) data.lua file is deleted from all stations including Pulse server - this will reboot stations, and (2) after reboot go to Server configuration -> Save + Apply - this will again reboot all stations
MTN-598 IP station fails to register if Hebrew name is too long
More than 12 characters entered causes registration problems
VSF-TURBINE 4.10.3.0
New Features - Turbine Intercom
SNOW-421 Advanced GPO configuration for Pulse and SIP
Turbine now has option to use standard Relay configuration or use the new and more Advanced GPO (output) configuration.
SNOW-1011 IP-LCM support in SIP, Pulse and Alphacom
IP-LCM is now supported in SIP, Pulse and Alphacom systems. This device has:
- 8 robust high power relays
- 8 robust inputs
- Powered via the TKIS-2 kit with PoE, PoE inject or external power supply
- All connections and features from the TKIS-2 kit available
New Features - Exigo Amplifiers
Bugfixes and Improvements - Turbine Intercom
MTN-1709 Fault led on all Turbine industrial stations, Turbine EX stations and Exigo Access panels can now be configured with custom behavior in Alphacom
SNOW-319 TKIE-3 support in Turbine firmware
TKIE-3 is now supported in Turbine firmware
SNOW-321 Implement Distributed AVC in SIP Mode
All "Turbine Devices" can be AVC Source (Ambient audio listener) or AVC destination.
SNOW-328 Adjust volume using SIP OPTIONS with X-Header
It is now possible to adjust volume using SIP OPTIONS with x-header by adding x-volume-level-override. The function will override the configured station volume
SNOW-552 Syslog support
Turbine now supports logging to the syslog server. Up to 3 syslog server destinations are supported
SNOW-592 AGC for line/mic in
Automatic Gain Control now works for Line/Mic in depending on configured input selection
SNOW-1173 New call functions in SIP
It is now possible to put call on hold or defer a call using DAK configuration