Difference between revisions of "1-3c. IP Stations – SoftClient (solution)"
From Zenitel Wiki
(→Related articles) |
|||
| (20 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | [[File:1-3c config.PNG|left|thumb| | + | [[File:1-3c config.PNG|left|thumb|450px|System configuration]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | + | __NOTOC__ | |
| − | |||
| + | === Install and configure the SoftClient === | ||
| + | * Download the file '''SoftClientSetup.msi''' from e.g. [[Downloads|Wiki download page]] or from Partnernet, and install it on the PC | ||
| + | * If not already done, change the IP address of the PC to 10.1.10.90, and subnet mask 255.255.0.0 | ||
| + | * Start the SoftClient, and select '''File''' -> '''Preferences''', and set these parameters: | ||
| + | [[File:1-3c solution1.PNG|thumb|left|250px|SoftClient: File -> Preferences window]] | ||
| + | <br style="clear:both;" /> | ||
| + | * '''Save Settings''' | ||
| + | * Select '''Configure Audio Device''' to adjust speaker and microphone levels | ||
| + | ===Configure the AlphaCom XE=== | ||
| + | *In AlphaPro go to '''Users & Stations''', and select physical number 40; 140 Station 40 | ||
| + | *Use the section on the right and change the configuration as follows: | ||
| + | [[File:1-3c solution2.PNG|thumb|left|400px|AlphaPro: Users & Stations window]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
| + | * Send the changes to the AlphaCom XE | ||
| + | [[File:SendChg.PNG|400px]] | ||
| + | |||
| + | === Troubleshooting === | ||
| + | * If the SoftClient does not register, check the following: | ||
| + | ** In AlphaWeb, System Configuration -> Filters, verify that port for '''IP Stations''' and '''VoIP Audio''' is enabled | ||
| + | ** In AlphaWeb, System Configuration -> Licenses, verify that there are licenses installed for the SoftClient | ||
<br><br><br><br> | <br><br><br><br> | ||
| Line 11: | Line 31: | ||
===Related articles === | ===Related articles === | ||
* [[1-3c. IP Stations – SoftClient (practice)]] | * [[1-3c. IP Stations – SoftClient (practice)]] | ||
| + | |||
| + | [[Category: AlphaCom practice]] | ||
Latest revision as of 10:04, 30 June 2022
Install and configure the SoftClient
- Download the file SoftClientSetup.msi from e.g. Wiki download page or from Partnernet, and install it on the PC
- If not already done, change the IP address of the PC to 10.1.10.90, and subnet mask 255.255.0.0
- Start the SoftClient, and select File -> Preferences, and set these parameters:
- Save Settings
- Select Configure Audio Device to adjust speaker and microphone levels
Configure the AlphaCom XE
- In AlphaPro go to Users & Stations, and select physical number 40; 140 Station 40
- Use the section on the right and change the configuration as follows:
- Send the changes to the AlphaCom XE
Troubleshooting
- If the SoftClient does not register, check the following:
- In AlphaWeb, System Configuration -> Filters, verify that port for IP Stations and VoIP Audio is enabled
- In AlphaWeb, System Configuration -> Licenses, verify that there are licenses installed for the SoftClient