View source for Vipedia And V2000 Update Manager Tool

The Update Manager software enables you to update the software on your Vipedia-12, V2000 and LSZDC cards. (These steps can also be followed with the Integra unit, as it contains the same components). 

The Update Manager is found in the tools folder of the software bundle which can be downloaded via the [https://repo.zenitel.com/index.php?title=Special:UserLogin&returnto=Main+Page&returntoquery= downloads page] on the Zenitel Wiki 


This article has also been written on the basis that there is sufficient understanding when modifying laptop Ethernet adapters.

==Before You Start - Important Notes==

{{Warn|Failure To Follow These Notes Could Lead To The Device Software Becoming Corrupted }}

* It is recommended that the Engineering Terminal/Laptop being used for the software update is connected via ethernet to ETH1 or ETH2 on either the Vipedia or Integra ROUTER
* It is recommended that the [[Vipedia-NET NetworkCardManager|Vipedia-NET NetworkCardManager.exe]] GUI is populated before running the UpdateManagere.exe tool so that it can be run during the Update Manager process.  
* Do not use the Update Manager (MPS Image) to update MPS microphones, please refer to: MPS Firmware Update Manual - U-0664-1005_Type_AB_FW_Update_01.pdf
* The update process may fail and cause corruption if you are connected to ETH3 or ETH4 on the Vipedia-NET card due to unintended Vipedia-NET card reboots. 
*Although the update manager shows "Update Complete" on the V2000s, the update to the LSZDCs is not complete until the SCT configuration is loaded into the system. DO NOT POWERCYCLE THE V2000 until you have loaded the Static Configuration using the SCT tool.

=Step by Step Instructions From Top To Bottom=

==Installing/Starting the Tools==

Navigate to the "Tools" folder within the software bundle 

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM TOOLS FILE STEP1.1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Opening The Tools Folder</td>
</tr>
</table>

Double-click UpdateManager.exe to open the Update Manager Tool

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM UPDATEMANAGERexe1.1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Opening UpdateManager.exe</td>
</tr>
</table>

Press the FTT button and navigate to the FTT which should have been installed beforehand. [[File Transfer Tool Instructions|(Please click here for File Transfer Tool install instructions)]] The path should be  C:\Users\YourWindowsUsername\ASL\FTT_VXX

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM FTT SELECT1.1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Selecting Firmware Transfer Tool File Path</td>
</tr>
</table>

==Setting Up the UpdateManager GUI==

Select Firmware_Transfer_Tool.exe and select "Open". The FTT box should now be populated with the path to the FTT.

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM FTT STEP1.1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Selecting Firmware Transfer Tool</td>
</tr>
</table>

Press the "SCT Config" button and navigate to the SCT configuration containing the Vipedia(s) and V2000(s) you wish to update and select open.

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM SCT SELECT1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Selecting System Configuration Tool File Path</td>
</tr>
</table>

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM SCT STEP1.1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Selecting System Configuration Config</td>
</tr>
</table>


You should now see the devices configured in the static configuration, listed as target devices within the Update Manager.

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDA UM DEVICE PRESCENCE1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Target Devices Shown In Blue</td>
</tr>
</table>

Ensure that all the devices you wish to update have their "Update" boxes ticked, within the device window.

Leave the "clear Config" options as default.

==Selecting Files for the Vipedia==

Press the “HCP” button and navigate to the following folder in the software bundle: \ASL_VIPEDIA-12_Vx.x.x\Software\01-VIPEDIA-12_&_INTEGRA\HCP\yourpreferredlanguage

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDA UM HCP SELECT1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Selecting Host Control Protocol File Path</td>
</tr>
</table>

Select the HCP file, followed by "Open" and the HCP box should populate with the required HCP software.

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM HCP FILE STAGE1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Host Control Protocol File Path</td>
</tr>
</table>

Follow the same procedure for the DSP and FPGA files. These can be found in the following locations:

DSP: \ASL_VIPEDIA-12_Vx.x.x\Software\01-VIPEDIA-12_&_INTEGRA\DSP 

FPGA: \ASL_VIPEDIA-12_Vx.x.x\Software\01-VIPEDIA-12_&_INTEGRA\FPGA 

==Selecting Files for the V2000 and LSZDC Cards==

Next, the software module for the V2000 frame and LSZDC files can be selected using the same process. The frame and LSZDC software can be found in the following locations:

Frame: \ASL_VIPEDIA-12_Vx.x.x\Software\02-V2000_&_INTEGRA\V2000\Frame_Controller 

{{Note| 
 
* If you have an R2 V2000 please select the alternative "V2000-R2" file as shown below  '' }}

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM V2000 FILE1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>V2000+LSZDC Software File Path</td>
</tr>
</table>

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM R2 FILE1png.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>V2000-R2 Software File Path</td>
</tr>
</table>

LSZDC Combined: \ASL_VIPEDIA-12_Vx.x.x\Software\02-V2000_&_INTEGRA\V2000\LSZDC\Combined 

LSZDC Bootloader: \ASL_VIPEDIA-12_Vx.x.x\Software\02-V2000_&_INTEGRA\V2000\LSZDC\Bootloader 

LSZDC Application: \ASL_VIPEDIA-12_Vx.x.x\Software\02-V2000_&_INTEGRA\V2000\LSZDC\Application 

NOTE: Once you have populated all fields you can use CTRL+S to save these parameters as a asl-tmp-pkg file. Any saved sessions can be loaded into the Update Manager using CTRL+L and selecting your saved .asl-tmp-pkg file. (Please note: This does not work for windows 11, Only windows 10.)

==Testing Node Reachability==

For peace of mind. to confirm visibility of all nodes, you can ping each IP address and ensure that you receive a response:

a. Type CMD in the Windows start box

b. In the command prompt terminal, type: ping xxx.xxx.xxx.xxx (where x = IP address of device)(I have used 192.168.1.2 as an example)

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM PING EXAMPLE1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Determining Node Reachability Example Using Ping</td>
</tr>
</table>



<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM ACTUALUPDATE1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Target Devices Updating</td>
</tr>
</table>

Once the Vipedia and V2000 update has started, you can also start the Vipedia-NET NET-VIPA update using the [[Vipedia-NET NetworkCardManager|NetworkCardManager.exe Tool]](For instructions on how to use this tool). Ensure that "Current Progress" is >1% prior to commencing Network Card Manager Update.

NOTE The Vipedia(s) will reboot when the update process starts. During the update process, you may see some elements retry multiple times in the debug window. This is normal while the Vipedia is rebooting. Once the Update Manager is finished you should see the following:

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM FINISHED UPDATE1.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Target Devices Updated</td>
</tr>
</table>

==Writing The Static System Config To The Devices==

Open the SCT configuration and complete the following:
 
1. Click the File Transfer Tool shortcut, which is represented as an F icon

2. Write the configuration to the system. Ensure that all slots populated with LSZDCs are included in the V2000 section of the SCT configuration file, as failure to do so will result in them not updating.


<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM SCT WRITE2-.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Writing the Static Configuration to the Nodes</td>
</tr>
</table>

Once loaded, you should see the "SELECT" LED on the amplifier in the configured slot, with functional LSZDC card fast flashing. This is to indicate that this LSZDC is being updated. Each LSZDC will update one by one starting on the configured slot and finishing on the final configured slot. 

If there are no slots currently in use, the LED's on the front panel of the V2000 will pulse continuously (The LED's on the front of the Electronics Module will flash on the Integra) and they will stop once the LSZDC update is complete.

To verify that the LSZDCs have updated, you can connect to the V2000 frame using the Amplifier Dynamic Tool (ADT). Please follow these steps within the SCT:

1. Click the Amplifer Dynamic Tool shortcut, represented as an A icon.

2. Ensuring you have the correct V2000 frame selected, press Connect.

3. By default, you will be on the "Settings and Information" tab when clicking between slots and this tab can be used to verify that the Firmware and Bootloader match the versions you have uploaded. 

4. You can also check the bottom of the ADT to verify the Frame Controller Version.

*Please Note: You may need to disconnect / reconnect to allow the ADT to update LSZDC card readings if you are checking the version updates while it is in progress.

<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
<tr style="rowspan:2;">
<td style="display: block; vertical-align: bottom;">[[Image:VIPEDIA UM CONNECTING TO ADT3.png|700px]]</td>
</tr>
<tr>
<td style='background-color:#efefef;'>Connecting to ADT</td>
</tr>
</table>

[[Category: Zenitel PAVA]]