Difference between revisions of "INCA Station Software upgrade"

Revision as of 10:12, 6 September 2017

This article describes how to upgrade the software in the INCA family of IP Stations via the web interface of the station.

Recommended:
It is possible to upgrade the software using the VS-IMT tool, see the article VS-IMT Upgrade Stations. 
The VS-IMT tool allows mass upgrade of stations.

Note that there is a separate Upgrade procedure for Turbine stations.

There is also a possiblity to upgrade via the web interface of the AlphaCom Server (AlphaCom mode) or to define Automatic Updates (SIP mode).

Upgrade via the web interface of the station

Upgrade of a single IP station

To upgrade the software from the web page of the IP Station:

Download the software package A100G80200.02_05_3_4.zip, unzip the file and store the files on a folder on your PC
Start the TFTP server and browse to the folder were the software files are located
Log on to the IP Station Web Server
Select Station Administration > Manual upgrade
Enter the IP address of the TFTP server (normally your PC)
Enter the name of the software Image file (include bin file extension)
Enter the CRC checksum (found in the text file from the downloaded software package)
Click Save settings to store this information.

Upgrade IP station software

The station will now try to contact the TFTP server. If the connection cannot be established or the file tftp_test.txt is missing from the folder, the message TFTP_CONN_ERROR is displayed. If the response is TFTP_CONN_OK the settings are saved, and the Upgrade button will appear.

Click on the Upgrade button to upgrade the software of the IP Station. The procedure takes about 3 minutes.
The transfer process can be monitored by selecting the Log viewer tab in the TFTP server program.

Upgrade via the web interface of the AlphaCom server

Note: This option is only available when the station is used in AlphaCom mode.

Upgrade multiple stations in one operation

Start the TFTP server and browse to the folder were the software file is located.
Log on to the AlphaCom XE Web Server AlphaWeb:

Select System Upgrade -> IP Stations Upgrade
Enter the IP address of the TFTP server, the filename of the software Image file and its CRC checksum. Click Save.
Select which IP Stations to upgrade (or all) and click Update Station List.
Click Start Upgrade Process.

IP station information list

The AlphaCom XE will tell each IP Station to contact the TFTP server, download the software image file and carry out the upgrade.
A short status description of the process will be displayed in the Upgrade status column. The message IPST:ERROR indicates that there is no connection to the TFTP server, or that the tftp_test.txt file is missing from the folder. The transfer process can be monitored by selecting the Log viewer tab in the TFTP server program.

Additional Information

Downloading and unzipping the software

Download the IP Station software file from the download page

Unzip the files to a folder on your PC, e.g. C:\software\IP station\
The zip file contains three files, one bin file and two txt files. Example files:

A100G80200.02_05_3_4.bin: The actual software image file
A100G80200.02_05_3_4.txt: You must open this file and make a note of (or copy to the clipboard) the CRC-checksum
tftp_test.txt: Used by the upgrade process to check the communication between the IP Station and the TFTP server

About the file name of the software package

Windows Explorer might be set to hide known file extensions, so the file might appear as A100G80200.02_05_3_4 in Windows Explorer, although the full file name is A100G80200.02_05_3_4.bin
The name of the software image file has to be entered with the extension .bin.

Upgrade in VLAN environment

During an upgrade, the IP station switch will not be VLAN aware. Make sure the IP station can reach the TFTP server from the native VLAN.

Upgrade in 802.1x environment

During an upgrade of the IP station, 802.1X will not be running. Thus if 802.1X reauthentication is enabled and is performed during the upgrade, the IP station will lose contact with the TFTP server (depending on the configuration when 802.1X authentication fails). If the IP station loses contact with the TFTP server, it will not be upgraded.

Installing a TFTP server on your PC

Settings for tftpd32. "Software" is set as base directory

Download the TFTP Server program tftpd32 standard edition (installer) from http://tftpd32.jounin.net/tftpd32_download.html.
For 64 bit computers download tftpd64 standard edition (installer)
Unzip the tftpdxx.yyy.zip file. (e.g. to C: \tftpdxx\)
Run the tftpdxx.exe file. The program is run by selecting the extracted .exe file, no installation is needed.
Select the base directory (e.g. C:\Software) by selecting the Settings button, then Browse
Turn off every thing except "TFTP Server" under Global Settings. Escpecially important to turn off "DHCP Server", as this server part of the tftpxx application may interfere with other DHCP servers in the network
The TFTP Server program must be running during the software upgrade process

Troubleshooting

In the case the upgrade is not successful it may be due to a windows setting.

For Windows XP: http://www.sysprobs.com/enable-ping-in-xp

For Windows7: http://www.sysprobs.com/enable-ping-reply-windows-7

For Windows10: http://www.sysprobs.com/enable-ping-reply-and-ftp-traffic-in-windows-10-and-server

@@ Line 9: / Line 9: @@
 There is also a possiblity to upgrade via the web interface of the AlphaCom Server (AlphaCom mode) or to define Automatic Updates (SIP mode).
-== Upgrade using the VS-IMT tool ==
-Procedure: <br>
-* Download and install the [[Downloads#VS-IMT_-_Intercom_management_Tool|VS-IMT tool]]
-* Download the software package [[Downloads#IP_Stations_and_IP-ARIO|A100G80200.02_05_3_4.zip]]. Don't unzip the file.
-* Start the VS-IMT tool
-* Select '''Create project''' or open an existing project, and start the wizard that takes you through the discovery and upgrade process, by selecting '''File''' > '''Launch Station Wizard'''
-* Press '''Next''' to go to Station Discovery. Enter the range of IP addresses (From - To) to search for, and press '''Search'''
-* When the discovery process is finished, select all stations in the list by checking the '''Select All''' flag
-[[File:IMT SelectAll.PNG|thumb|left|500px|Station Discovery window]]
-<br style="clear:both;" />
-* Press '''Next''' two times. You've now come to the "Upgrade Stations" window:
-[[File:IMT UpgradeWin.PNG|thumb|left|500px|The Upgrade Stations window]]
-<br style="clear:both;" />
-* Import the software package into the VS-IMT tool, and start the upgrade:
-** Select '''Import image...''', and browse to the '''A100G80200.02_05_3_4.zip''' file, and select '''Open'''
-** Select the "INCA Image" = '''A100G80200.02_05_3_4'''
-** In the list box, select the stations to upgrade. Use '''Ctrl + click''' to select multiple stations.
-[[File:IMT INCA upgrade 2530.PNG|thumb|left|500px|INCA image and stations selected, ready to start the upgrade]]
-<br style="clear:both;" />
-:* Press the '''Upgrade''' button to start the upgrade process. The status is shown on the screen. The Status will become '''''Success''''' when the station is up and running after the upgrade.
 == Upgrade via the web interface of the station ==