Actions

INCA Station Kit Restore Factory Defaults: Difference between revisions

From Zenitel Wiki
No edit summary
 
(20 intermediate revisions by 3 users not shown)
Line 1: Line 1:
Restore to Factory Default for IP Stations without Display and Key
{{APS}}
* IP Speaker - [[IP Ceiling Loudspeaker - 1401002100|1401002100]]/[[IP Horn Loudspeaker - 1401002500|1401002500]]
This procedure is applicable for:
* IP Heavy Duty - [[IP Heavy Duty Station - 1008072200|1008072200]]
* IP Substation Kit - [[IP Substation Kit - 1008090200|1008090200]]
* IP Substation Kit - [[IP Substation Kit - 1008090200|1008090200]]
The procedure can be used on the IP Substation Kit - 1008090200 an on the IP Master Station Kit - 1008093000.
* IP Master Station Kit [[IP Master Station Kit - 1008093000|100809300]]


The Factory Default can be either set to Static IP 169.254.1.100 or activate DHCP.
<div style="text-align:left;"> <youtube width="300" height="180">WP9m-DG0hMU</youtube>  </div>


Connect a push button ('''KEY1''') between pin 1 and 4 on the P4 connector.


[[File:Load Defaults without KEY.PNG|left]]
The unit can be set to use either '''Static IP''' or '''DHCP'''. On the rear side of the PCB there is a red status LED. Pay attention to this LED during the restore procedure:
<br style="clear:both;" />


--------
[[File:Load Defaults without KEY.PNG|right|thumb|800px|Connect a push button between pins 1 and 4]]


=== Restore with Static IP ===
== Procedure ==
# While pressing the button, power up the station kit.
# Connect a push button ('''KEY1''') between pin 1 and 4 on the P4 connector.
# When the station kit LED starts blinking, release the button '''after exactly 2 blinks'''.
# While pressing the button, power up the station kit and keep the button pressed.
# Let the LED blink for '''exactly 2 more times''', then press the button again.
# Release the button '''after exactly 2 flashes''' of the LED.
# Keep the button pressed until the LED '''blinks fast 2 times''' indicating a successful reset with static IP.
# Let the LED flash for '''exactly 2 more times''' (Static IP) or '''exactly 4 more times''' (DHCP), then press the button again.
# Release the button and the station kit will restart with the factory default settings.
# Keep the button pressed until the LED '''flashes fast 2 times''' (Static IP) or '''flashes fast 4 times''' (DHCP) indicating a successful reset.
# Release the button and the station will restart with the factory default settings.


<u>'''Factory default values:'''</u>
* Station IP address: '''169.254.1.100'''
* AlphaCom IP address: '''169.254.1.5'''
* Username: '''admin''' (Software 01.06 and earlier: '''ADMIN''')
* Password: '''alphaadmin''' (Software 01.06 and earlier: '''alphacom''')


------
== Factory default values ==
*Station Mode: '''Pulse'''
*Station IP address: '''169.254.1.100''' or '''DHCP'''
*Username: '''admin'''
*Password: '''alphaadmin'''


=== Restore with Activated DHCP ===
The DHCP option is available from software version 01.07.
# While pressing the button, power up the station kit.
# When the station kit LED starts blinking, release the button '''after exactly 2 blinks'''.
# Let the LED blink for '''exactly 4 more times''', then press the button again.
# Keep the button pressed until the LED '''blinks fast 4 times''' indicating a successful reset with activated DHCP.
# Release the button and the station kit will restart with the factory default settings.
'''Factory default values:'''
* Station IP address: (determined by DHCP server)
* AlphaCom IP address: '''169.254.1.5'''
* Username: '''admin''' (Software 01.06 and earlier: '''ADMIN''')
* Password: '''alphaadmin''' (Software 01.06 and earlier: '''alphacom''')


[[Category: INCA - Restore Factory Defaults and Software Upgrade]]
[[Category: INCA - Restore Factory Defaults and Software Upgrade]]

Latest revision as of 13:25, 15 May 2018

APS.png

This procedure is applicable for:


The unit can be set to use either Static IP or DHCP. On the rear side of the PCB there is a red status LED. Pay attention to this LED during the restore procedure:

Connect a push button between pins 1 and 4

Procedure

  1. Connect a push button (KEY1) between pin 1 and 4 on the P4 connector.
  2. While pressing the button, power up the station kit and keep the button pressed.
  3. Release the button after exactly 2 flashes of the LED.
  4. Let the LED flash for exactly 2 more times (Static IP) or exactly 4 more times (DHCP), then press the button again.
  5. Keep the button pressed until the LED flashes fast 2 times (Static IP) or flashes fast 4 times (DHCP) indicating a successful reset.
  6. Release the button and the station will restart with the factory default settings.


Factory default values

  • Station Mode: Pulse
  • Station IP address: 169.254.1.100 or DHCP
  • Username: admin
  • Password: alphaadmin
Retrieved from "https://wiki.zenitel.com/w/index.php?title=INCA_Station_Kit_Restore_Factory_Defaults&oldid=185998"
MediaWiki spam blocked by CleanTalk.